风扇转子叶片周向积叠的三维气动优化设计

为了研究优化环境对优化结果的影响，利用商业软件NUMECA对某风扇第一级转子叶片进行了气动优化设计，并对比研究了第一级转子单排叶片的优化及其在整级环境中的优化结果。研究发现．单叶排优化后．虽然能提高整级风扇的效率，但是由于匹配的原因，整级风扇在整个流量范围内总压比都比优化前的有所减小；在级环境中优化后，该级风扇的效率和稳定工作范围都扩大了，且保证了级压比不变，其优化效果比单叶排的优化效果好。     

防静电白色热控涂层的耐空间环境及工艺性能

研究了防静电白色热控涂层（ACR-1）的耐空间环境性能及工艺性能。在模拟空间环境设施中研究了紫外辐照、电子辐照和质子辐照对涂层太阳吸收率（αs）的影响。结果表明ACR-1在地球静止轨道环境中具有较高的稳定性；经过3000当量太阳小时（ESH）的紫外光辐照后，△αs为0．02；质子辐照效应对涂层仅。的变化影响较大。另外，研究了涂层厚度对αs和其与基材结合力的影响，以及基材表面处理工艺对涂层在-196—150℃冷热交变循环试验中可靠性的影响。     

模拟地球同步轨道辐照环境对光学太阳反射镜性能的影响

研究了模拟地球同步轨道辐照环境对卫星用温控涂层-光学太阳反射镜(OSR)性能的影响。对所研制的两类OSR 片进行的辐照试验项目有,真空紫外辐照、低能电子和两种能量的质子辐照。此外还进行了等离子体环境条件下的表面充/放电效应试验。经过相当于安装在地球同步轨道卫星南北极位置处,在空间七年所受到的电子、质子和紫外辐照总剂量的辐照后,导电型OSR 的太阳光谱吸收率α_s 由0.068增加到0.078,法向发射率ε_n 由0.83降低到0.72;而非导电型OSR的α_s 由0.066增加到0.085,ε_n 由0.82降低到0.76。表面充/放电试验的结果表明:导电型OSR 的充电电位仅在15～40V 之间,而非导电型OSR 的充电电位则可高达13kV。因此导电型OSR能有效地控制表面的充/放电现象。     

微重力场中对流—辐射—传质系统的地面模拟技术

研究了微重力条件下对流－辐射－传质稳态系统的地面相似模拟技术，进一步发 温度－材料综合保护技术。通过采取补偿热流，调整壁面热流密度分布的方法，保持了原型与尺寸适当缩小后的模型的Ｎｕ数，Ｓｈ数，材料，温度，湿度不变，从而实现模型与原型流动，换热和传质相似。     

防静电白色热控涂层的空间环境性能试验

通过在氧化锌晶格中掺入重金属离子，得到具有防静电功能的白色颜料，再以丙烯酸树脂为粘合剂制备出空间飞行器外表面用的ACR－1防静电白色热控涂层；研究了空间环境效应（包括紫外辐照，电子和质子辐照）对该热控涂层太阳吸收率的影响并与有机硅白色热控涂层进行了比较，地面模拟空间环境试验研究结果证明，ACR－1防静电白色热控涂层具有良好的空间稳定性。     

微重力下管肋式空间辐射器的整体优化分析

建立了向一重力环境下管肋式空间辐射器传热过程的数学模型，并以单质量散热量最大和热载体驱动功率最小为优化目标，对管式空间辐射器进行了优化分析。     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

Numerical simulations of water spray on flame deflector during the four-engine rocket launching

This paper aims to study on the cooling effect with two types of water spray nozzle on the flame deflector during the four-engine launch vehicle take-off. To accurately simulate the two-phase flow of the rocket gas with multispecies and the water spray, the three-dimensional compressible Navier-Stokes equations, discrete ordinates methods and realizable k-Ɛ turbulence model are used to establish the rocket supersonic plumes impact model. The Eulerian dispersed phase (EDP) model was used to simulate the water spray into the exhaust gas. The accuracy and effectiveness of the gas-liquid flow model are verified by a good agreement between simulation results and experimental data. On this basis, a series of numerical simulation studies under different water injection position are performed. The results show that the high temperature regions, along the axis of engines on the deflector plate, have no significant temperature decreasing effect by water spray from the nozzles mounted on the apex of the deflector, and the high temperature converts a large quantity of water into vapor near the plume boundary, which would decrease the flow conductivity. With the cooling spray nozzle fixed directly to the deflector plate, the temperature decrease effect is obvious and the effect of thermal shock on deflector plate induced by exhaust plume is reduced, so that it can prevent the flame deflector from thermal ablation. The study results provide indepth information and engineering guidance for designing the water spray systems and increasing the safety of the launch process.     

火星表面热环境对航天器热控影响分析

火星大气对太阳辐射产生吸收和散射作用，同时还将与火星表面航天器发生对流换热。热设计时难以直接评估对流、辐射和导热三种换热对航天器的影响，从而确定主要的控温途径。在调研火星表面辐射、大气等热环境的基础上，从线性化传热系数和对流辐射比的角度对比分析了辐射、对流和导热对航天器的影响。器表辐射传热系数随光学属性和温度的变化范围为0.3～1.4W/(m2·℃)，对流传热系数随风速变化为0.2～1.5W/(m2·℃)，器内导热传热系数可控制在0.25W/(m2·℃)以下。结果表明，太阳辐射较火星表面和天空辐射而言是主要外热源，航天器表面的辐射和对流换热为两条并联换热途径，两者均可成为主要换热途径，器内导热传热是控制航天器内外隔热的主要可控因素。     

CFD软件自动化验证确认云平台设计与实现

针对大型计算流体力学(CFD)软件的验证与确认,为了减少人工成本,提高软件质量和开发效率,并适应于未来高性能计算发展的要求,基于云计算思想,提出了自动化测试云平台的解决方案。该方案采用模块化的浏览器/服务器(B/S)网络架构;利用LAMP(Linux+Apache+MySQL+PHP/Python)开发工具;建立了持续集成的专业数据库;构建了涵盖可靠集群监控、复杂作业调度及大规模并行计算功能的云端环境;实现了通过便捷的网络访问,自动加载测试算例、提交集群计算、监测实时进度、自动化后处理、输出分析结果,并提供丰富的实验对比图、误差分析报表和汇总报告等;完成了对大型CFD软件的自动化验证与确认。将该方案应用于某大规模并行计算的CFD软件,验证了该解决方案的可行性与实用性。