轨姿控推进系统用电磁阀性能仿真研究

轨姿控推进系统采用电磁阀控制内部流体通路的开启与断流,从而实现其重复启动和脉冲工作.在轨姿控推进系统快速稳定工作问题的研究中,电磁阀的性能对推进系统至关重要.针对轨姿控推进系统用电磁阀,基于电磁学及运动学等基本原理,建立了电磁阀动态数学模型,利用Matlab Simulink软件进行了动态仿真,得到了电磁阀动态响应特性;采用CFD软件对阀门内部流场进行数值模拟仿真,获得了精确的静态流阻特性,直观展现了电磁阀动态流场,为电磁阀的性能优化和轨姿控推进系统的性能提高提供依据.     

基于多智能体强化学习的空间机械臂轨迹规划

针对某型六自由度（DOF）空间漂浮机械臂对运动目标捕捉场景,开展了基于深度强化学习的在线轨迹规划方法研究。首先给出了机械臂DH （Denavit-Hartenberg）模型,考虑组合体力学耦合特性建立了多刚体运动学和动力学模型。然后提出了一种改进深度确定性策略梯度算法,以各关节为决策智能体建立了多智能体自学习系统。而后建立了"线下集中学习,线上分布执行"的空间机械臂对匀速直线运动目标捕捉训练系统,构建以目标相对距离和总操作时间为参数的奖励函数。最后通过数学仿真验证,实现了机械臂对各向匀速运动目标的快速捕捉,平均完成耗时5.4 s。与传统基于随机采样的规划算法对比,本文提出的自主决策运动规划方法求解速度和鲁棒性更优。     

基于覆盖圆的太阳同步回归轨道卫星目标轨迹调整方法

遥感卫星星座在环境监测、地理测绘等领域运用中,需要考虑目标轨迹分布的优化问题.轨迹分布与星座的重访能力和进出站间隔保持等应用需求密切相关.目前对星下点轨迹分布的优化和调整还缺乏准确实用的方法,存在卫星数目增多带来的计算量增加问题和对多种需求综合考虑不够的问题.为了克服现有技术的不足,解决太阳同步回归轨道遥感卫星星座的目...     

Autonomous navigation to quasi-periodic orbits near translunar libration points

Libration-point missions have been very useful and successful. Due to the unstable nat-ures of most of these orbits, the long-time stationkeeping demands frequent maneuvers and precise orbit determinat...     

太阳同步轨道卫星光学特性

为了分析太阳同步轨道卫星的光学特性,对FY-1卫星的可见光和红外波段光学信号进行了仿真计算和模拟试验验证.通过对外部辐射及内部热源的分析,计算了卫星的温度场,采用随机起伏表面算法模拟表面覆盖材料外表面,通过阴影遮挡判断及双向反射分布函数(BRDF, Bi-directional Reflectance Distribution Function)模型计算卫星对外部辐射的反射特性,编程计算得到在可见光0.4~1.0μm和红外8~14 μm,14~16 μm波段下卫星的光学特性.结果表明红外辐射亮度与表面温度相关,8~14 μm最大约90 W/(m²·sr)、14~16 μm最大约20 W/(m²·sr).空间可见光辐射强度具有明显的镜面反射效应,卫星主体峰值2 200 W/sr.通过地面模拟测量空间目标的温度和红外辐射验证了温度及红外辐射仿真计算模型,可见光辐射强度仿真计算结果与地面模型卫星测量结果误差在20%以内.     

椭圆轨道非线性相对运动模型的周期解与应用

在长期的航天器编队飞行中传统的基于线性相对运动模型设计编队保持轨道的方法会引起较多的燃料消耗.首先采用摄动法解析地求得了考虑二阶非线性项时椭圆轨道相对运动模型的周期性条件和周期解;然后以此周期解为参考轨道设计了基于Lyapunov稳定的PD保持控制律.仿真结果表明:基于椭圆轨道非线性相对运动模型的周期解较基于椭圆轨道线性相对运动模型的周期解,精度明显提高;以前者为参考轨道的保持控制与以后者为参考轨道的保持控制相比,燃耗明显降低.     

地球静止轨道卫星硅太阳电池在轨特性分析

空间辐照效应的影响,使太阳电池输出功率随其在轨时间的推移而逐渐衰减。文章以2颗在轨的地球静止轨道卫星为研究对象,对某类我国自主研发的硅太阳电池的在轨输出功率衰减率进行了分析。并针对所获得的相关遥测参数,通过数值统计与数学分析的方法,采用确定的计算公式得出太阳电池阵的总输出电流,用以表征其输出功率。文章提出了一种曲线平移...     

星载SAR椭圆轨道全零多普勒导引方法研究

多普勒中心频率在星载合成孔径雷达（SAR）成像中,直接影响方位向的模糊度及图像的定位精度。全零多普勒导引方法通过调整偏航角和俯仰角,使多普勒中心频率为零,但现有方法都导致残余多普勒中心频率较大。文章利用椭圆轨道下多普勒中心频率的表达式,将多普勒中心频率分为仅与俯仰角相关部分,以及与俯仰角和偏航角都相关的部分,令两部分分...     

静止轨道卫星在轨温度参数变化规律研究

分析了静止轨道在轨三轴稳定卫星各面上温度参数的变化规律,并通过理论计算得到卫星各面上光强的变化曲线,研究了温度参数变化与对应面上光强的关系,建立了温度参数与光线的线性模型,结果表明模型与实际数据能较好地吻合,对温度参数的预测以及故障的判断具有一定的参考价值.     

Feasibility of performing space surveillance tasks with a proposed space-based optical architecture

Under ESA contract an industrial consortium including Aboa Space Research Oy (ASRO), the Astronomical Institute of the University of Bern (AIUB), and the Dutch National Aerospace Laboratory (NLR), proposed the observation concept, developed a suitable sensor architecture, and assessed the performance of a space-based optical (SBO) telescope in 2005. The goal of the SBO study was to analyse how the existing knowledge gap in the space debris population in the millimetre and centimetre regime may be closed by means of a passive optical instrument. The SBO instrument was requested to provide statistical information on the space debris population in terms of number of objects and size distribution. The SBO instrument was considered to be a cost-efficient with 20 cm aperture and 6° field-of-view and having flexible integration requirements. It should be possible to integrate the SBO instrument easily as a secondary payload on satellites launched into low-Earth orbits (LEO), or into geostationary orbit (GEO). Thus the selected mission concept only allowed for fix-mounted telescopes, and the pointing direction could be requested freely. Since 2007 ESA focuses space surveillance and tracking activities in the Space Situational Awareness (SSA) preparatory program. Ground-based radars and optical telescopes are studied for the build-up and maintenance of a catalogue of objects. In this paper we analyse how the proposed SBO architecture could contribute to the space surveillance tasks survey and tracking. We assume that the SBO instrumentation is placed into a circular sun-synchronous orbit at 800 km altitude. We discuss the observation conditions of objects at higher altitude, and select an orbit close to the terminator plane. A pointing of the sensor orthogonal to the orbital plane with optimal elevation slightly in positive direction (0° and +5°) is found optimal for accessing the entire GEO regime within one day, implying a very good coverage of controlled objects in GEO, too. Simulations using ESA’s Program for Radar and Optical Observation Forecasting (PROOF) in the version 2005 and a GEO reference population extracted from DISCOS revealed that the proposed pointing scenario provides low phase angles together with low angular velocities of the objects crossing the field-of-view. Radiometric simulations show that the optimal exposure time is 1–2 s, and that spherical objects in GEO with a diameter of below 1 m can be detected. The GEO population can be covered under proper illumination nearly completely, but seasonal drops of the coverage are possible. Subsequent observations of objects are on average at least every 1.5 days, not exceeding 3 days at maximum. A single observation arc spans 3° to 5° on average. Using a simulation environment that connects PROOF to AIUB’s program system CelMech we verify the consistency of the initial orbit determination for five selected test objects on subsequent days as a function of realistic astrometric noise levels. The initial orbit determination is possible. We define requirements for a correlator process essential for catalogue build-up and maintenance. Each single observation should provide an astrometric accuracy of at least 1”–1.5” so that the initially determined orbits are consistent within a few hundred kilometres for the semi-major axis, 0.01 for the eccentricity, and 0.1° for the inclination.