基于深度神经网络的客机总体设计参数敏感性分析

飞机总体主要设计参数敏感性分析揭示了总体主要设计参数对飞机特性指标的影响,有助于总体设计方案的决策。针对宽体客机总体主要设计参数敏感性问题,根据其总体主要设计参数和特性指标的特点,以及多学科间的耦合关系,建立了深度神经网络模型。该深度神经网络模型以客机总体主要设计参数为输入,对特性指标进行预测。在深度神经网络模型中,设置了多个输入层、多个输出层以及多个分块的隐藏层,从而模拟客机总体主要设计参数对特性指标的影响以及不同特性指标之间的相互作用。测试结果表明,与传统代理模型相比,深度神经网络模型对客机特性指标的预测精度更高,多参数适应性更好。利用该深度神经网络模型对客机总体主要设计参数进行敏感性分析。分析结果表明,机翼1/4弦线后掠角在30°~31.5°时,有利于减少最大起飞重量和起飞平衡场长;发动机海平面最大静推力和机翼面积对客机直接使用成本、最大起飞重量等特性指标的影响最为显著。     

基于GMF方法的捕风一号风速反演分析

全球尺度高时空分辨率海面风场探测是当前全球气象研究及预报预测领域的关注热点之一,传统海面风场探测技术存在测量区域有限,且受天气环境限制明显等问题.基于全球导航卫星系统-反射(GNSS-R)测量技术风速反演原理,以捕风一号1级数据产品为输入,欧洲中期天气预报中心再分析风速数据为参考风速,采用地球物理模型函数(GMF)方法...     

基于正反问题耦合的压气机特性快速预测方法

提出一种基于正反问题耦合的压气机特性快速预测方法,根据压气机一维设计理论,通过对满足流量及压比设计指标的反问题求解快速得出压气机的气动布局方案,在此基础上结合非设计点损失和落后角模型通过正问题求解得出全工况压气机特性,再根据预测特性与目标的偏差调整气动布局方案,以此通过对正反问题的耦合求解实现对压气机特性的合理快速预测...     

纤维桥连对复合材料Ⅰ型层间断裂韧性的影响

 采用ASTM D 5528标准对T700/9916复合材料单向板进行了试验,研究了双悬臂梁(DCB)试验中桥连纤维对Ⅰ型层间断裂韧性的影响。根据试验观察,提出桥连区存在单(s区域)、双纤维桥连区域(d区域)的分析模型,其中d区域内一点上桥连纤维的数量是s区域的两倍;通过对桥连纤维和悬臂梁相互作用的分析,推导出呈指数形式递减的单根纤维桥连力-转角函数。由此得到整个悬臂梁的桥连力函数,并对DCB试验进行了分析,得到的模拟曲线与试验曲线吻合较好。研究结果表明本文提出的纤维桥连模型能够真实地反映桥连纤维在裂纹扩展过程中的作用方式。     

一种模块化航空有源滤波器的研究

 航空有源滤波器(AAPF)是解决飞机供电系统中电能质量问题的一种先进方案,而模块化设计对航空有源滤波器灵活性、可维护性和可靠性的提升作用巨大。首先提出并研究了一种新型模块化航空有源滤波器,分析了主电路数学模型及其混合载波PWM(CH-PWM)调制方式;其次基于损耗对比分析进行了主电路拓扑优化,推导了模块均压控制律并给出了系统控制策略;最后进行了仿真和实验验证。结果表明,模块化航空有源滤波器能够有效补偿航空电网中由典型非线性负载产生的谐波和无功电流分量,三相电网电流的总谐波畸变率(THD)均在5%以下,补偿效果显著。     

FGM板三维层合模型及热-噪声载荷下的动态响应研究

 为了有效地分析热-噪声联合载荷作用下的飞行器功能梯度壁板结构的非线性动态响应,提出了运用复合材料多层壳单元建立功能梯度材料(FGM)板的层合有限元建模新方法,研究了FGM板在热曲屈前、后状态下复杂的非线性时域动态响应特性,并探讨了梯度指数、热曲屈系数及声压级(SPL)等参数对FGM板非线性动态跳变响应的影响规律。FGM板三维层合建模新方法避免了采用常规有限元法(FEM)建模时需要在厚度方向划分大量单元的缺点;求解FGM板非线性动态响应时采用的隐式积分方案避免了模态叠加法对参与模态选择的经验性要求及模态截断造成的信息丢失等缺陷。仿真结果表明:FGM板层合有限元建模新方法合理可行、过程简便、计算精度高;研究发现:陶瓷-金属FGM板在热屈曲后的抗声振性能并不像热屈曲前那样介于金属板和陶瓷板之间,而是表现最差;热屈曲系数及声压级的组合形式是导致FGM板发生非线性跳变响应的主要影响因素。     

An adaptive turbo-shaft engine modeling method based on PS and MRR-LSSVR algorithms

In order to establish an adaptive turbo-shaft engine model with high accuracy, a new modeling method based on parameter selection (PS) algorithm and multi-input multi-output recursive reduced least square support vector regression (MRR-LSSVR) machine is proposed. Firstly, the PS algorithm is designed to choose the most reasonable inputs of the adaptive module. During this process, a wrapper criterion based on least square support vector regression (LSSVR) machine is adopted, which can not only reduce computational complexity but also enhance generalization performance. Secondly, with the input variables determined by the PS algorithm, a mapping model of engine parameter estimation is trained off-line using MRR-LSSVR, which has a satisfying accuracy within 5&. Finally, based on a numerical simulation platform of an integrated helicopter/ turbo-shaft engine system, an adaptive turbo-shaft engine model is developed and tested in a certain flight envelope. Under the condition of single or multiple engine components being degraded, many simulation experiments are carried out, and the simulation results show the effectiveness and validity of the proposed adaptive modeling method.     

Research on failure criterion of composite based on unified macro- and micro-mechanical model

A new unified macro- and micro-mechanics failure analysis method for composite structures was developed in order to take the effects of composite micro structure into consideration. In this method, the macro stress distribution of composite structure was calculated by commercial finite element analysis software. According to the macro stress distribution, the damage point was searched and the micro-stress distribution was calculated by reformulated finite-volume direct averaging micromechanics (FVDAM), which was a multi-scale finite element method for composite. The micro structure failure modes were estimated with the failure strength of constituents. A unidirectional composite plate with a circular hole in the center under two kinds of loads was analyzed with the traditional macro-mechanical failure analysis method and the unified macro- and micro-mechanics failure analysis method. The results obtained by the two methods are consistent, which show this new method’s accuracy and efficiency.     

A method of multi-objective reliability tolerance design for electronic circuits

Tolerance design plays an important role in reliability design for electronic circuits. The traditional method only focuses on the consistency of output response. It is not able to meet the needs of increasing development of electronic products. This paper researches the state of related fields and proposes a method of multi-objective reliability tolerance design. The characteristics of output response and operating stresses on critical components are both defined as design objectives. Critical components and their operating stresses are determined by failure mode and effect analysis (FMEA) and fault tree analysis (FTA). Sensitivity analysis is carried out to determine sensitive parameters that affect the design objectives significantly. Monte Carlo and worst-case analysis are utilized to explore the tolerance levels of sensitive parameters. Design of experiment and regression analysis are applied in this method. The optimal tolerance levels are selected in accord with a quality-cost model to improve consistency of output response and reduce failure rates of critical components synchronously. The application in light-emitting diode (LED) drivers indicates details and potential. It shows that the proposed method provides a more effective way to improve performance and reliability of electronic circuits.     

幂律型流体雾化SPH方法数值分析

幂律型流体的雾化过程存在复杂的界面运动,用传统网格法很难精确追踪运动界面.为研究幂律型流体的雾化特性,运用SPH方法对典型的双股幂律型流体撞击雾化问题进行三维数值分析.根据文献实验,采用SPH方法模拟获得与实验条件相应的数值结果,对比后表明,二者雾化角相当吻合,数值结果还成功捕捉到液膜向液丝的破碎过程及网状的液丝分布状态,验证了方法的有效性.分析了射流速度和撞击角度对雾化角的影响,得到雾化角随着射流速度和撞击角度的增加而增大;对雾化后的速度场进行数值分析后表明,撞击点附近,惯性力的作用使速度场变化剧烈;在流体远离撞击点的过程中,粘性耗散作用使速度场趋于稳定,但速度大小小于初始撞击速度.