用于高硬度模具钢SKD11的铣刀几何角度优化及试验

在切削淬硬模具钢SKD11中,为开发和选用与生产条件相匹配的具备优化几何角度的高性能铣刀,对专用于高硬度模具钢SKD11铣刀的几何角度进行了优化及试验分析.设计了4类不同几何结构的TiAlN复合涂层铣刀.从切削力、切削振动、切削变形、铣刀耐用度以及铣刀磨损机理等方面对这4类铣刀高速铣削SKD11过程进行了研究,综合评价其铣削性能,确定了在常用的高速加工生产条件下的优化铣刀.所选择的优化槽形铣刀具的寿命比之其他刀具延长3倍,在切削力和切削振动方面,该刀具具有最稳定的表现,而且大小较其他刀具下降70%.     

型腔尖角的轨迹优化

在铣削型腔尖角加工过程中,当环切法加工的行间距离比较大时,型腔尖角处将会出现加工残余.由于刀具与工件的接触线增加,使得尖角处铣削力增大.因此,采用了双圆弧过渡来处理型腔中的尖角,该方法能保证以尽可能大的行距走刀,缩短了加工时问,提高了加工效率,同时还可以清除尖角处的残余留量.尖角处刀具轨迹进行合理优化后,刀具沿着改进的轨迹快速运行,满足了高速铣削型腔的加工要求.最后,实验验证了该方法的有效性.     

硬质合金刀具高速铣削航空铝合金时的磨损形态及磨损机理

对硬质合金整体立铣刀高速铣削加工航空铝合金时的刀具磨损形态及其磨损机理进行了观察和分析.结果表明:在高速切削条件下,硬质合金整体立铣刀的磨损形态主要表现为涂层破坏、月牙洼磨损、微崩刃、剥落和破损等.磨损机理主要是粘结磨损、扩散磨损以及疲劳磨损.与常速铣削磨损机理的不同之处在于高速旋转形成的热、力耦合的应力场对硬质合金刀具的作用与冲击影响占主导地位.     

Experimental investigation of rotary sinking electrochemical discharge milling with high-conductivity salt solution and non-pulsed direct current

Electrochemical milling is a modified technique of traditional electrochemical machining (ECM) that can be used to manufacture some helicopter transmission system parts. The use of rotary tools and an inner-jet electrolyte supply pattern can greatly improve the material removal rate (MRR) in a single pass. However, the feed speed is generally limited to minimize the tool wear. To increase the MRR, electrical discharge machining (EDM) is introduced into the electrochemical milling process. The tool rotation is employed to interrupt the discharge and the high-conductivity salt solution and non-pulsed direct current power supply are also adopted to increase ECM, eventually, a new machining method is proposed, which can be called rotary sinking electrochemical discharge milling (RSECD milling). The mechanism of it is explored in this study by analyzing the machined current, MRR, surface morphology, and tool wear at different applied voltages and feed speeds. Besides, the RSECD milling using the tool with a larger diameter is also conducted to further verify the effectiveness. In particular, the MRR can be increased by 742.5% when using the tool with a diameter of 20 mm at the applied voltage of 20 V.     

刀具织构轮廓对碳纤维增强复合材料面下损伤影响的切削仿真研究

为减小碳纤维增强复合材料（CFRP）加工时的面下损伤深度,创建了基于二维Hashin准则的宏观连续动态切削CFRP有限元模型,分析了切削力和面下损伤深度与纤维方向角之间的变化趋势,通过引入织构刀具来降低切削力及面下损伤深度,比较了沟槽形织构刀具、圆形织构刀具、三角形织构刀具切削CFRP的切削力和面下损伤。结果表明,不同织构刀具的切削力和面下损伤深度随纤维方向角变化趋势一致,均在0°时最小,90°达到最大值;织构刀具相对传统无织构刀具切削CFRP时均降低了切削力和面下损伤深度,其中圆形织构刀具降低程度最大;仿真模型经实验验证准确有效。     

Cutting tool temperature prediction method using analytical model for end milling

Dramatic tool temperature variation in end milling can cause excessive tool wear and shorten its life, especially in machining of difficult-to-machine materials. In this study, a new analyt-ical model-based method for the prediction of cutting tool temperature in end milling is presented. The cutting cycle is divided into temperature increase and decrease phases. For the temperature increase phase, a temperature prediction model considering real friction state between the chip and tool is proposed, and the heat flux and tool-chip contact length are then obtained through finite element simulation. In the temperature decrease phase, a temperature decrease model based on the one-dimension plate heat convection is proposed. A single wire thermocouple is employed to mea-sure the tool temperature in the conducted milling experiments. Both of the theoretical and experi-mental results are obtained with cutting conditions of the cutting speed ranging from 60 m/min to 100 m/min, feed per tooth from 0.12 mm/z to 0.20 mm/z, and the radial and axial depth of cut respec-tively being 4 mm and 0.5 mm. The comparison results show high agreement between the physical cutting experiments and the proposed cutting tool temperature prediction method.     

整体叶盘盘铣加工切削力及刀具磨损实验研究

本文对整体叶盘开槽粗加工时从切削速度、进给量、径向切深等切削参数对切削力的影响进行研究。选用正交实验的方法进行盘铣切削实验,得到切削参数对切削力的影响变化规律,并对刀具在切削过程中的磨损进行分析,进一步验证优化的切削参数,为整体叶盘的盘铣加工参数的合理制定与加工工艺的优化提供参考。     

低温微量润滑技术喷嘴方位正交试验研究

低温微量润滑切削技术作为一种理想的绿色冷却润滑方式,已经成为机械加工领域研究的热点之一.选择外部微量润滑与低温冷风的集成作为低温微量润滑系统的实现方式,给出了确定系统喷嘴方位的3个参数:喷射方向与进给方向夹角β、喷嘴仰角α和喷嘴距切削区的距离d,并分别构建了其几何模型.针对β角,给出了最优β角与切宽半径比(B/R)的曲线.通过正交试验研究了喷嘴方位的3个参数(β、α、d)对低温微量润滑切削性能影响的重要程度.结果表明,距离d对切削性能的影响最大;其次是β角;α角的影响最小,可根据实际工况选择α在30°～60°即可.     

镍基高温合金铣削加工的残余应力研究

对硬质合金与陶瓷两类不同刀具分别以低速湿式铣削和高速干铣削方式加工镍基高温合金GH4169时的已加工表面残余应力进行研究.采用X射线衍射法测量铣削后的工件表面残余应力.采用涂层硬质合金刀具在较低铣削速度30～90m/min并浇注切削液的条件下铣削GH4169时,可在工件表面形成残余压应力或相对较小的残余拉应力,对残余应力数据进行统计分析.结果表明,刀具和铣削速度对表面残余应力均有显著影响,而且表面残余应力总体上随着每齿进给量的增加而呈现拉应力增加的趋势.采用涂层Al2O3-SiCw和Sialon陶瓷刀具以较高铣削速度300～1100m/min干铣削GH4169时,工件表面都将形成很大的残余拉应力.镍基高温合金GH4169的精加工更适合采用硬质合金涂层刀具并浇注切削液充分冷却,而陶瓷刀具干铣削则更适合于GH4169的粗加工.     

星图匹配制导中的关键技术

为了提高新一代弹道导弹的快速、机动反击能力和射击精度，采用星光，惯性组合制导足最佳的选择。本论文给出了基于双星敏感器的、星图匹配制导系统的关键技术。提出了根据弹道设计导航星表．极大地简化了弹载星表；提出了一种适用于星光制导的凸多边形箅法，合理地减少了匹配的星对角距数目。这两项技术保证了星图匹配制导技术的实用性。提出了一种分离初始定位、定向误差及平台漂移误差方法。采用凸多边形的星图识别算法可同时获得多颗星的瞬时位置，结合恒星在像平面的位置可解算导弹在赤道惯性系和发射点惯性系的三轴姿态，最后，给出了导弹初始定位、定向误差的数学表达式。仿真结果表明了该方法的有效性。