Latent heat flux and air temperature anomalies along an active fault zone associated with recent Iran earthquakes

Pre-earthquake physical and chemical interactions in the earth’s ground may cause anomalies in latent heat flux, air and surface temperature. Earthquakes occur when the energy accumulated in rocks releases. Sometimes, the movements of the ground cause ruptures in the earth’s surface and sometimes the two sides of an existing fault shift towards each other. In a structurally complex and inhomogeneous collision region such as the Iranian Plateau, seismicity is not the result of activity of a single fault but is due to energy discharge in fault zones hundreds of kilometers wide.     

复合材料机体结构选用树脂体系的探讨

由于复合材料的优点如此之多，复合材料的应用日益广泛，但在具体设计时应选用何种固化温度的树脂体系人们有不同的见解，本文将结合工程设计体会作些探讨。     

高温下直流电位法测量裂纹长度的应用

介绍了直流电位法测量疲劳裂纹长度方法的基本原理、实现方法、及所需配置的仪器,并对有关影响因素作了分析.该测量系统主要用于在高温下测量各种材料在恒幅载荷下的疲劳裂纹扩展和门槛值试验中的疲劳裂纹长度,可以提高测量疲劳裂纹长度的自动化水平.     

EUV Observations Above Polar Coronal Holes

We derive electron temperature and density as a function of height up to 0.2 R_⊙ above the limb in polar coronal holes, using five EUV data sets recorded by the SOHO Coronal Diagnostic Spectrometer between July 1997 and February 1998. Radial T and N distributions, averaged in a 2° to 10° range of position angles, are the same above the North and South coronal holes. They do not show any time variability over a period of seven months. Polar plumes are found to have lower electron temperature and higher density than the interplume lanes. The electron density slope suggests that the proton temperatures are twice as high as the electron temperatures. This revised version was published online in June 2006 with corrections to the Cover Date.     

建筑物温度场红外测试的研究

研究了采用红外热像图快速测试建筑物外表面温度场的方法，提出了一种基于信息融合的修正方法。     

9SiCr合金刃具钢在不同介质淬火后性能比较

通过对9SiCr合金刃具钢在清水、锭子油和高压气体等淬火介质中淬火对比实验,研究了9SiCr合金刃具钢在不同介质淬火工艺处理后的性能。研究结果表明,水淬火时试件表面与中心的温差较大,锭子油次之,高压气体较小;试件高压气体淬火时,温度梯度小,整个断面冷却比较均匀,可以预计,相应的热应力和热变形也比较小;应用适当压力的氮气能够实现淬透性比较好的9SiCr合金刃具钢的淬火处理。     

TiC和ZrC颗粒增强钨基复合材料

用粉末冶金热压法制备了ＴｉＣｐ／Ｗ和ＺｒＣｐ／Ｗ两种钨基复合材料，对其高温强度进行了研究，结果表明，随着温度提高，两种复合材料的抗弯强度开始时逐渐提高，当ＴｉＣｐ／Ｗ复合材料达到１０００℃时有最大值１１５５ＭＰａ，ＺｒＣｐ／Ｗ复合材料在８００℃时最大值８２９ＭＰａ，分别比各自的室温强度提高５７％和１７％。而后，随温度的进一步提高，复合材料的强度又下降，分析了复合材料高温增强的机理。     

温湿度闭环控制实验设备的开发与研制

本文介绍了自己开发的温湿度闭环控制实验设备的性能特点，并给出了组织结构，硬件线设计和程序框图。     

直升机批生产中的疲劳质量检验方法

本文论述了直升机关重件在批量生产中,疲劳质量控制所采用的抽检方法以及抽检原则。文中给出的大批量产品的抽样检验判断方法、小批量生产产品的抽样检验判断方法、最佳抽样检验法和改进的最佳抽样检验法均适用于直升机关重件的抽样检验。     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).