轴对称跨音速流中无激波超音速区的设计

本文直接从音速线出发计算了一个旋成体跨音速绕流超音速泡中的特征线网。提出了从音速线开拓到一条超音速线的方法,计算了无旋轴对称流的特征线网,发现其特点是不能跨越对称轴线,并对其原因作了初步的讨论。本文的计算结果可应用于物面修形。     

脉冲式转速表的设计,校验与应用

本文就航空发动机转速测量技术状态进行了简要分析,对适用于超轻型飞机的具有原理、结构简单,造价低等优点的“脉冲式转速表”的设计、校验等进行了详细的论述,并对该原理的推广应用进行了分析讨论。     

用非线性模型分析气动液阀的启动特性

对气动液阀的启动过程建立了非线性数学模型,分析了尺寸参数和推进剂进、出口压力对该阀的启动特性的影响。计算结果表明：在保证必要的工作寿命的前提下,适当地增大控制腔气孔的直径或增大靠近控制腔的活塞端面直径,降低推进剂进口和出口的压力有利于提高该阀的响应能力。     

导弹燃气流瞬态温度测量系统设计

介绍了采用蓝宝石黑体腔光纤作为传感器的导弹燃气流瞬态温度测量系统的测量原理、系统组成,阐述了其硬件功能模块设计,给出了软件设计算法及蓝宝石黑体腔光纤高温计的标定方法。     

多孔层板换热特性实验研究

本实验选取了一种典型结构的多孔层板作为研究对象 ,进行了换热特性实验研究。研究了改变冷热气流吹风比对该型层板冷却效果的影响。另外 ,对该型多孔层板的冷却效果沿中轴线顺气流方向的变化规律也作了深入的研究。并给出了层板局部 N ux 和冷却效果 E关于局部 Rex 及冷热气流吹风比 M的数学拟合表达式。     

三维瞬态导热温度场边界元计算及一阶数学奇异的处理

推导了三维瞬态导热温度场边界元解法的积分方程和离散代数方程，并编制了相应的计算机程序，采用坐标变换的解析消去法，处理边界元的一阶数学奇异点，从而提高了算法的数值精度。用本程序计算了正方体和圆柱环瞬态导热温度场，数值解与解析解的吻合程度令人满意。     

喷口辐射热泄漏对延伸段壁温分布的影响

引入喷口的热辐射泄漏损失，导出辐射冷却推力室壁温的计算方程。分析表明，考虑与不考虑喷口热损失二者相比较，前者壁温约下降７０℃。本结果可为喷管延伸段材料的选取提供更为科学的理论依据。     

含内热源球壳的复合传热特性及其表面温度均匀性研究

应用计算流体动力学方法,对带内热源的空腔球壳所涉及的含导热、自然对流和辐射换热的耦合传热问题进行了数值建模,得到了球壳空腔内、外侧流体的温度场、速度场。在数值模拟基础上,提出并试验验证了能有效提高球壳外表面温度均匀性的电加热绳方案。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

Study on the Microstructure and Dielectric Properties of Barium Strontium Titanate Thin Films Prepared by Sol-gel Method

Sr05Ba0.5-xBixTiO3 （BST） thin films were fabricated on a Pt/SiO2/Si substrate by the sol-gel method. Then follows an investigation of the influeoces of bismuth （Bi） on the microstructures and the dielectric properties of Sr0.5Ba0.5-xBixTiO3 （BST） thin films. The microstructures of the BST thin films were examined by the XRD and the TEM techniques. Tetragonal perovskite crystal grains were observed in BST thin films. Increasing Bi^3＋ doping ration in BST will lead to decrease of the grain size. It is found that Bi^3＋ doping decreases the dielectric loss and improves the frequency dispersion of the BST thin films. Not only is compressed the peak of temperature-dependence of dielectric constant of Bi^3＋-doped BST thin films but also moves into the low-temperature region. Moreover, the average Curie tem- perature decreases gradually with the Bi^3＋ contents increasing.