火箭发动机橡胶件贮存寿命的蒙特卡罗仿真

应用蒙特卡罗（ Ｍ－ Ｃ） 随机抽样方法，对固体导弹的火箭发动机橡胶构件的老化特性进行了仿真计算，通过对其残余变形积累和贮存寿命的可靠性评估，作出了相应的关系曲线图。从计算结果和关系曲线可以看出，所得出的结论是符合实际情况的，表明文中方法的正确性和可行性。     

采样机械臂关节月表环境适应性设计

文章针对月球表面采样任务对机械臂关节防尘、耐高低温和轻量化的特殊要求,提出一种由永磁同步电机驱动、2K-H行星减速器+谐波减速器传动的关节设计方案。该方案采用电机的齿槽转矩提供关节制动力矩,并采用前馈力矩补偿控制的方法消除齿槽转矩引起的速度波动,节省了制动器的配置;通过控制减速器传动侧隙、电机定子与壳体的过盈量及密封垫片厚度,实现关节在-100~160℃高低温环境的热匹配和防尘。仿真分析和样机试验结果验证了关节设计方案可满足月表采样的月面特殊环境要求。     

栗实蛾幼虫空间格局及抽样技术研究

对7个板栗园栗实蛾幼虫空间格局进行了研究.结果表明,栗实蛾幼虫在板栗园中的分布是遵循负二项分布的聚集分布,其中Iwao的m~*-m回归模型为m~*=3.532 3+1.071 0 m,Taylor幂模型为lgv=0.591 3+1.130 4 lgm.对各聚集度指标的分析结果显示:在板栗园中的栗实蛾幼虫彼此之间互相吸引,分布的基本成分是个体群,个体群为聚集分布,且在任何密度下都是聚集的,聚集强度随着密度的升高而增大.导致栗实蛾幼虫在板栗园中呈聚集分布的原因是由该虫本身的习性和环境共同造成的.栗实蛾幼虫虫口密度调查的最适理论抽样数公式为n＝t~2/D~2(4.532 3/m+0.071 0).     

Analysis of Chang’e-5 lunar core drilling process

Chang’e-5 explorer successfully acquired lunar regolith core samples from depths of greater than 1 m of lunar surface. This study analyzed the lunar core drilling process based on the telemetry data, image information, and returned samples to optimize the sampling device design and enhance the understanding of the lunar regolith. In particular, a prediction method for the projected drilling path and local terrain fitting of drilling dip angle was proposed based on the flight events recorded during the core drilling process and the image information acquired before, during, and after sampling. The results revealed that the drilling dip angle of Chang’e-5 was approximately 2.3°, and the deviation of the drilling length and depth was less than 2 mm. For continuous drilling, a fusion method based on telemetry data and image information was applied to determine the demarcation point of drilling with and without the lunar soil. The position of the demarcation point implied that the drilling point remained at approximately 6 mm loose soil, thereby lagging the action of the force response. Additionally, a characteristic parameter comparison method was proposed for the lunar and ground drilling to analyze the status of the lunar soil. Furthermore, the analysis results revealed that the majority of the Chang’e-5 drilling samples were derived from 0–73.8 cm below the lunar surface and few samples were extracted below 73.8 cm, as the drilling encountered several rocky regions. Moreover, the drilling point exhibited two prominent stratification variations at ～28.7 cm and ～70 cm below the lunar surface. Ultimately, the preliminary relationship between sample dissected position in soft tube and drilling displacement was analyzed. The segmented estimation results can support research on subsurface lunar soil.     

模块化月球表层采样力学模型

因不受作业空间的限制，月球表层采样机具设计形式多样，为建模分析带来较大难度。为避免不同结构机具分析时重复建模，建立了一种模块化的月球表层采样力学模型。该模型将复杂的采样机具拆分成若干个基本面单元，基于朗肯土压力理论、最大抗剪强度理论和地基极限承载力理论对面单元在采样过程中的受力进行分析，组合各个面单元所受到的力获得复杂机具的力学模型。基于不同机具形式与贯入角度的模拟月壤贯入试验，对理论模型进行了试验验证，通过引入月壤密度沿深度的影响修正公式，将理论模型的误差率降低至8.2%。结果证明该力学模型和模块化理论可行，为后期月球表层采样机具的设计研发提供了参考。     

Influence of lunar regolith compressibility on sampling performance of thick wall spiral drills

A 2 m class robotic drill was sent to the Moon and successfully collected and returned regolith samples in late 2020 by China. It was a typical thick wall spiral drill (TWSD) with a hollow auger containing a complex coring system to retain subsurface regolith samples. Before the robotic drill was launched, a series of laboratory tests were carried out to investigate and predict the possible drilling loads it may encounter in the lunar environment. This work presents how the sampling performance of the TWSD is affected by the regolith compressibility. Experiments and analysis during the drilling and sampling process in a simulated lunar regolith environment were conducted. The compressibility of a typical lunar regolith simulant (LRS) was measured through uni-directional compression tests to study the relationship between its inner regolith stress and bulk density. A theoretical model was established to elucidate the cutting discharge behavior by auger flights based on the aforementioned relationship. Experiments were conducted with the LRS, and the results show that the sampling performance is greatly affected by the flux of the drilled cuttings into the spiral flight channels. This work helped in scheduling reasonable drilling parameters to promote the sampling performance of the robotic drill in the Chinese Chang'E 5 mission.     

基于多维数值积分的高阶确定采样型滤波方法

基于多维数值积分讨论了确定采样型滤波器,这一类滤波器的不同之处体现在对滤波器中均值和方差的计算,这一问题与数值积分密切相关.针对以往确定采样型滤波器在提高滤波精度的同时会增加计算量,通过分析高斯权值积分,采用完全对称积分公式,计算积分节点、节点个数及权重,相比高斯厄米特滤波减少了计算量,同时滤波精度可达到五阶以上.选取典型算例对新的滤波方法仿真分析,验证了该滤波方法的可行性和有效性.     

Pressure distribution feature-oriented sampling for statistical analysis of supercritical airfoil aerodynamics

In the field of supercritical wing design, various principles and rules have been summarized through theoretical and experimental analyses. Compared with black-box relationships between geometry parameters and performances, quantitative physical laws about pressure distributions and performances are clearer and more beneficial to designers. With the advancement of computational fluid dynamics and computational intelligence, discovering new rules through statistical analysis on computers has beco...     

基于B1c/B2a/B3I北斗三频实时 高采样率动态PPP分析

为了分析北斗三号新信号的三频实时动态PPP定位性能，首先推导了三频两两组合无电离层模型和三频非差非组合模型的观测方程。基于山东建筑大学CORS站观测得到的北斗三号B1c/B2a/B3I三频信号1s采样率数据，使用iGMAS提供的超快速精密星历预报部分，制定了基于B1cB3I-B2aB3I三频无电离层两两组合、B1cB2aB3I三频非差非组合以及用于对比分析的B1cB2a、B1IB3I两种双频无电离层共四种定位方案。然后利用Net_Diff软件进行实时动态PPP实验，对超快速精密轨道和钟差预报部分的精度和稳定度以及实验解算结果进行分析，对比不同定位方案的定位性能。实验分析表明，两种三频定位方案定位性能均优于B1cB2a双频定位方案，定位精度能达到0.462m和0.479m，收敛至分米所需时间能达到45.8min和62.8min；B1IB3I方案定位性能优于两种三频定位方案，定位精度和收敛速度能达到0.228m和6.6min。