基于自适应代理模型的结构动力可靠度分析方法

结构动力可靠度分析对于衡量结构的安全状态和工作性能具有重要的指导意义。采用一种同时考虑 动态激励载荷和材料力学性能参数随机性的动力可靠度计算高效方法,通过建立不确定性材料力学性能参数 与条件动力可靠度之间的 Kriging代理模型,推导动力可靠度的解析表达式;提出一个新的学习函数来构建自 适应的 Kriging代理过程,通过复合材料飞行器蒙皮骨架结构在随机振动载荷和随机材料力学性能参数共同作 用下的动力可靠度分析对所提方法的准确性与高效性进行验证。结果表明:所提方法不仅能够避免使用代理 模型对动力可靠度求解时由于使用数值积分所引入的误差,同时能够使用尽可能少的计算成本获得准确的动 力可靠度结果。     

强光光学零件加工误差频谱分析与控制方法研究

本文利用功率谱密度分析磁流变抛光表面的敏感频率误差,发现走刀步距与中高频误差具有直接的关联性,通过小波算法确定其分布区域后,采用大束径的光顺抛光法对敏感频率误差进行控制,测试结果表明中高频误差得到了有效控制。本研究对强光光学零件加工误差的频谱分析、表征和控制具有指导意义。     

数据采集系统动态特性的总体评价

数据采集系统动态特性的辨识和评价，是其总体性能评价中至关重要的一个目标。本文通过选取几个相互比较独立的指标来总体描述数据采集系统的动态特性，然后通过几个特殊的模型化方法将其动态特性分别以动态有效位数、传递函数、阶跃响应曲线和幅频特性、相频特性的方式给出，从而解决了数据采集系统动态特性的总体评价问题。     

飞机机身近区电磁散射建模研究

采用物理光学法和一致性几何绕射理论，分析机身各 球面波照射下的近场电磁散射特性几何绕射并建立其雷达散射截面（ＲＣＳ）数学模型，同时对于复杂机身的前部，采用面元油、即采用双三次Ｂ样条技术对机外形进行拟合，然后再用一致性几何绕射理论进行计算。种方法具有一定的可信度。     

计算机辅助的低空风切变改出优化控制

介绍了动态系统的计算机辅助直接优化方法的原理及其在低空风切变改出飞行中的应用，利用较真实的风切变工程化模型，选择适当的控制函数模型，性能准则及其约束条件，通过计算机直接地，系统地和迭代地探寻最优条件，对飞机改出低空风切变控制进行了优化，获得了最佳改出性能飞行参数曲线，并与没有优化的改出引导策略结果作了比较，结果表明，通过优化，飞机改出低空风切变的性能获得了明显的改善。     

基于拉盖尔函数的卫星姿态预测控制方法

针对卫星在空间站中进行绕飞检测时的姿态控制问题，考虑卫星的姿态轴需要躲避禁飞区域并指向期望位置，提出了一种基于拉盖尔函数的模型预测控制方法，实现了对卫星姿态轴的控制。在模型预测控制方法的基础上，通过拉盖尔函数，将优化多个控制输入转换为优化少数的拉盖尔系数，建立了拉盖尔模型预测的控制策略，改善了传统的模型预测控制方法计算效率差的问题，减少了优化时间。采用卫星在空间站中绕飞的模型进行数值仿真验证，结果表明该方法能够使卫星的姿态轴躲避禁飞区并到达指定位置。与传统方法相比，这种基于拉盖尔函数的模型预测控制策略能够提高优化效率，减少计算时间。     

Aerodynamic optimization design for high pressure turbines based on the adjoint approach

A first study on the continuous adjoint formulation for aerodynamic optimization design of high pressure turbines based on S2surface governed by the Euler equations with source terms is presented.The objective function is defined as an integral function along the boundaries,and the adjoint equations and the boundary conditions are derived by introducing the adjoint variable vectors.The gradient expression of the objective function then includes only the terms related to physical shape variations.The numerical solution of the adjoint equation is conducted by a finitedifference method with the Jameson spatial scheme employing the first and the third order dissipative fluxes.A gradient-based aerodynamic optimization system is established by integrating the blade stagger angles,the stacking lines and the passage perturbation parameterization with the quasi-Newton method of Broyden–Fletcher–Goldfarb–Shanno(BFGS).The application of the continuous adjoint method is validated through a single stage high pressure turbine optimization case.The adiabatic efficiency increases from 0.8875 to 0.8931,whilst the mass flow rate and the pressure ratio remain almost unchanged.The optimization design is shown to reduce the passage vortex loss as well as the mixing loss due to the cooling air injection.     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Practical compensation for nonlinear dynamic thrust measurement system

The real dynamic thrust measurement system usually tends to be nonlinear due to the complex characteristics of the rig, pipes connection, etc. For a real dynamic measuring system,the nonlinearity must be eliminated by some adequate methods. In this paper, a nonlinear model of dynamic thrust measurement system is established by using radial basis function neural network(RBF-NN), where a novel multi-step force generator is designed to stimulate the nonlinearity of the system, and a practical compensation method for the measurement system using left inverse model is proposed. Left inverse model can be considered as a perfect dynamic compensation of the dynamic thrust measurement system, and in practice, it can be approximated by RBF-NN based on least mean square(LMS) algorithms. Different weights are set for producing the multi-step force, which is the ideal input signal of the nonlinear dynamic thrust measurement system. The validity of the compensation method depends on the engine’s performance and the tolerance error0.5%, which is commonly demanded in engineering. Results from simulations and experiments show that the practical compensation using left inverse model based on RBF-NN in dynamic thrust measuring system can yield high tracking accuracy than the conventional methods.     

高超声速飞行器动态神经网络反推自适应控制

针对高超声速飞行器纵向模型的高度非线性特点,在考虑模型不确定性的情况下,提出了高超声速飞行器动态神经网络调节函数反推自适应控制方法.对给定的速度指令,引入积分型Lyapunov函数设计跟踪控制器,取消了控制增益一阶导数上界的限制,且避免了控制器的奇异性;对给定的高度指令,引入调节函数技术,设计了反推控制器,避免了将模型化为严反馈形式;采用动态神经网络对未知系统动态进行自适应在线逼近.根据Lyapunov理论证明了设计的控制律保证了闭环系统的稳定性与指令跟踪的精确性.仿真结果验证了该方法的可行性及有效性.