考虑滑流影响的埋入式进气道气动特性分析与流动控制研究

研究滑流对埋入式进气道性能的影响机理对于发动机的稳定性具有重要意义。针对某型涡桨发动机 滑油散热器进排气道系统,基于 CFD技术建立系统的螺旋桨滑流与滑油散热器内流一体化数值模拟方法,进 行考虑滑流影响的滑油散热系统埋入式进气道气动设计仿真分析;针对埋入式进气道由于吸入边界层低能气 流导致通过散热器流量低的问题,设计4组涡流发生器进行主动流动控制。结果表明:滑流使得进气道中的气 流偏离,难以形成稳定漩涡,容易发生流动分离;而合理设计的涡流发生器可以有效改善埋入式进气道内流场 特性,并使通过散热器的流量提高12%。     

Numerical Simulation of Rotor Flow Field Based on Overset Grids and Several Spatial and Temporal Discretization Schemes

A numerical method based on solutions of Euler/Navier-Stokes (N-S) equations is developed for calculating the flow field over a rotor in hover. Jameson central scheme, van Leer flux-vector splitting scheme, advection upwind splitting method (AUSM) scheme, upwind AUSM/van Leer scheme, AUSM+ scheme and AUSMDV scheme are implemented for spatial discretization, and van Albada limiter is also applied. For temporal discretization, both explicit Runge-Kutta method and implicit lower-upper symmetric Gauss-Seidel (LU-SGS) method are attempted. Simultaneously, overset grid technique is adopted. In detail, hole-map method is utilized to identify intergrid boundary points (IGBPs). Furthermore, aimed at identification issue of donor elements, inverse-map method is implemented. Eventually, blade surface pressure distributions derived from numerical simulation are validated compared with experimental data, showing that all the schemes mentioned above have the capability to predict the rotor flow field accurately. At the same time, vorticity contours are illustrated for analysis, and other characteristics are also analyzed.     

卫星用两种单相流体回路方案对比研究

单相流体回路系统是航天器主动热控技术中的一种重要方式。文章概述了流体回路的工作原理及理论基础，总结了单相流体回路的设计思路，结合某卫星型号，设计了两种流体回路方案，在SINDA／FLUINT中建立数值仿真模型进行分析计算，并比较了两种方案的应用性能。结果显示，将单相流体回路系统应用于卫星，可取得较好的控温效果。     

低速高湍流度90°弯管流动数值模拟

分析了曲率对弯曲管道流动的影响 ,给出了曲率修正的双层 k-ε湍流模型 ,并数值模拟了非均匀来流低速高湍流度 90°弯管内流动。文中比较了曲率修正双层 k- ε湍流模型的计算结果与实验结果 ,以及双层 k- ε湍流模型和逆压力梯度修正双层 k- ε湍流模型的计算结果。通过比较 ,发现经过曲率修正后的双层 k- ε湍流模型更好地模拟了非均匀来流低速高湍流度 90°弯管内流动。同时比较了壁面参数的插值方法 ,发现在弯曲管道流动模拟中对壁面参数进行一阶插值比零阶插值能更好地模拟真实流场     

可压缩流动激波装配在格心型有限体积法中的应用

发展了一种基于格心型有限体积方法(FVM)的激波装配算法。通过定义网格节点属性可以灵活调用激波装配和激波捕捉计算方法。在使用激波装配方法时,激波节点运动速度和下游运动速度通过Rankine-Hugoniot(R-H)关系式获得,同时采用非结构动网格技术描述激波的运动以及调整其他网格节点的位置。流过激波面元的通量为上游单元的基本通量,物理概念更加清晰,通量计算也更为准确。在计算过程中,网格节点属性可以发生变化,以此实现对带有拓扑变化流场的描述。数值试验表明:本文提出的计算方法不但具有较高的计算精度,同时能有效地避免由于捕捉激波而出现的数值问题。     

大型水陆两栖飞机侧风起降的滑流影响分析

大型水陆两栖飞机AG600的动力装置为安装在机翼上的4台同向旋转涡轮螺旋桨发动机，针对1：15缩比模型带动力风洞试验显示的螺旋桨滑流对侧风起降状态的偏航力矩不稳定影响，对全机带动力风洞试验模型进行了大规模并行非定常数值计算，再现了风洞试验现象，通过流动机理分析明确其产生原因主要是左侧滑时右外翼分离和垂尾背鳍涡破裂，这些原因和数值模拟的准确性也为后期的风洞试验所证实。考虑到模型风洞试验中尺度限制造成的低雷诺数和高螺旋桨转速，为保证飞行安全，继续采用该非定常方法对全尺寸飞机真实侧风起降状态进行了详细数值分析和偏航稳定性评估。研究结果显示，在飞行雷诺数和螺旋桨转速下，相同侧风范围内风洞试验显示的流动不稳定因素基本消失，偏航稳定性允许的侧风范围明显增加。本研究实现了四发螺旋桨飞机起降状态横向气动特性的滑流影响非定常数值分析，建立了基于计算流体力学的风洞与飞行雷诺数效应的相互关系，进行了偏航稳定性的虚拟试飞评估，研究成果也为AG600飞机的首飞和飞行试验所验证。     

激光功率与底面状态对选区激光熔化球化的影响

为研究激光功率与底面状态对选区激光熔化熔池流动的影响，基于离散单元法建立了选区激光熔化铺粉模型，采用粒径分布与实验相符的马氏体时效钢粉末分别铺展到平坦底面和增材底面上，将计算获得的粉末分布导入到基于有限体积法建立的选区激光熔化熔池计算流体力学模型中，研究激光功率和基板底面粗糙度对熔池流动和熔道表面形貌的影响。采用激光单道扫描实验验证铺粉模型和选区激光熔化模型。结果表明：随着激光功率的降低，单位长度的球化数量增加；由于增材底面使熔池润湿性变差，同时又对熔池流动行为产生扰动，使得增材粗糙底面上熔道的球化数量增加。选区激光熔化铺粉模拟及激光单道扫描模拟结果与实验结果吻合较好。本研究可为选区激光熔化工艺中工艺参数的选择提供理论指导。     

Numerical prediction and wind tunnel experiment for a pitching unmanned combat air vehicle

The low-speed flowfield for a generic unmanned combat air vehicle (UCAV) is investigated both experimentally and numerically. A wind tunnel experiment was conducted with the Boeing 1301 UCAV at a variety of angles of attack up to 70 degrees, both statically and with various frequencies of pitch oscillation (0.5, 1.0, and 2.0 Hz). In addition, pitching was performed about three longitudinal locations on the configuration (the nose, 35% MAC, and the tail). Solutions to the unsteady, laminar, compressible Navier–Stokes equations were obtained on an unstructured mesh to match results from the static and dynamic experiments. The computational results are compared with experimental results for both static and pitching cases. Details about the flowfield, including vortex formation and interaction, are shown and discussed, including the non-linear aerodynamic characteristics of the vehicle.     

基于图剖分的多块结构网格负载平衡方法

负载平衡是影响并行计算性能的重要因素。针对多块结构网格,给出了一种改进的多层次图剖分负载平衡方法。该方法设计了新的网格剖分算法,采用改进的子块分裂方法与图剖分算法的循环调用实现结构对接网格剖分,并通过建立不同物体重叠网格间的连接关系,实现了结构重叠网格的负载平衡。采用2个典型算例对方法进行了对比验证,数值结果表明,子块分裂方法对剖分结果具有重要影响,采用循环调用算法及改进的子块分裂方法能有效地实现计算负载均衡及通信量优化,同时显著减少了网格块数及因虚网格导致的内存需求,有利于提高并行效率。该负载平衡方法与网格拓扑无关,适用于多块结构对接网格及重叠网格,且整体型剖分方式对于多块结构重叠网格具有更好的剖分效果。     

Development process of muzzle flows including a gun-launched missile

Numerical investigations on the launch process of a gun-launched missile from the muzzle of a cannon to the free-flight stage have been performed in this paper. The dynamic overlapped grids approach are applied to dealing with the problems of a moving gun-launched missile. The high-resolution upwind scheme(AUSMPW+) and the detailed reaction kinetics model are adopted to solve the chemical non-equilibrium Euler equations for dynamic grids. The development process and flow field structure of muzzle flows including a gun-launched missile are discussed in detail.This present numerical study confirms that complicated transient phenomena exist in the shortly launching stages when the gun-launched missile moves from the muzzle of a cannon to the freeflight stage. The propellant gas flows, the initial environmental ambient air flows and the moving missile mutually couple and interact. A complete structure of flow field is formed at the launching stages, including the blast wave, base shock, reflected shock, incident shock, shear layer, primary vortex ring and triple point.