微动工作台的研制及特性研究

介绍了一种根据仿生学原理设计而成的由电致伸缩微位移器为驱动元件的大范围高精度的微动工作台,该工作台采用电致伸缩微位移器直接驱动的柔性铰链机构,使其既可以在小范围内实现高精度的微动,又可以实现大范围的宏动。同时还对工作台的特性进行了测试实验和分析。     

Influence of fuel injection position and equivalent mixture ratio on chemical non-equilibrium effects of single expansion ramp nozzle

Chemical non-equilibrium flow was investigated for the scramjet single expansion ramp nozzle(SERN) with a strut-based liquid-kerosene-fueled combustor.Two-dimensional Reynolds-averaged Navier-Stokes(RANS) equations were solved with the species conservation equation for continuous phase and the renormalization group(RNG) k-ε turbulence model.Lagrangian discrete-phase model was analyzed for liquid-kerosene droplets behavior in the supersonic stream.Combustion was simulated by kerosene surrogate fuel's 10-species and 13-step reduced reaction kinetics mechanism with use of Arrhenius's laminar finite rate model.Parametric studies were carried out to estimate the influence of different fuel injection positions and equivalent mixture ratios on the SERN chemical non-equilibrium effects.Numerical calculation results show that the strut-based combustor enables convenient modeling of various SERN entry conditions,which is similar with many preceding investigations,by changing the injector strut position and controlling the mass flow rate of each injector.Chemical non-equilibrium effects function in the whole SERN,especially in the initial flow expansion region,leads to obviously higher SERN performance of the non-equilibrium flow than that of the frozen flow.Furthermore,the distributed fuel injection pattern plays a significant role in enhancing the combustion efficiency in combustor,but weakening the chemical non-equilibrium effects funciton in SERN.Additionally,while the equivalent mixture ratio increases,the SERN thrust coefficient and lift coefficient rise gradually,and the increment of non-equilibrium flow in relation to frozen flow becomes higher as well.To be specific,the equivalent mixture ratio is 0.6,the maximum increment of thrust coefficient and lift coefficient are 11.6% and 25% respectively.      

微型燃气轮机喷嘴射流和雾化特性研究

为在微型燃气轮机内营造低氧贫燃氛围以实现液体燃料的节能减排,利用可适性多普勒激光测速仪APV/LDV对改造喷嘴附近截面进行了测量和分析,用以考查近喷嘴处的气液混合夹带情况以及雾滴尺寸及分布。结果发现：增加外部涡旋气流后,喷孔附近雾滴的动量增大,雾锥内出现一小回流区,对应湍流度较大区域附近;燃烧时较大切向动量及湍流度利于空气与周围高温烟气迅速混合形成低氧环境,并和雾滴掺混进行热量和动量的传递;喷孔出口雾化角增大,使得雾滴更加分散,利于雾化、气液混合和传热传质;所有实验工况雾滴平均直径低于50μm,且为偏高斯分布。该研究为液体燃料喷嘴的设计提供了参考,可作为微型燃气轮机燃烧室热态反应物流场的参考依据。     

二次气射流角对涡轮叶问燃烧室的影响研究

为研究二次气射流角对涡轮叶间燃烧室的影响,设计了3种带有不同二次气射流角的涡轮叶间燃烧室模型,利用FLUENT软件的Realizablek-8湍流模型、PDF燃烧模型、D0辐射模型和离散相模型对燃烧室的流动和燃烧进行数值模拟。结果表明：涡轮叶间燃烧室具有高效率（99.2％）的特点,增大二次气射流角可使切向动量分量增加、油滴蒸发变慢、出口温度场分布不均匀、总压损失增加。     

冲压燃烧室内的燃料扩散性能研究

应用含组分守恒方程的质量平均Navier-Stokes方程和B-L代数湍流模型,本文数值模拟了带支板引射器的模型燃烧室内部的流场结构,对比研究了支板引射器数量以及燃料注入角度对燃料混合性能的影响.在计算过程中,对方程中的对流项采用了空间为二阶精度的TVD和AUSMPW格式,扩散项则采用了二阶中心差分离散.采用流体力学时间步内的当地积分法克服了非平衡源项的刚性问题,保持了LU-SSOR隐式算法的高效率.研究结果表明,燃料有角度注入及采用多支板构型可提高燃料的混合性能.     

某机第4级压气机转子叶片榫头折断故障分析

阐明了某机第4级压气机转子叶片在榫头部位断裂的故障特点。故障分析表明：经长期使用的叶片在修理厂大修时，为满足叶片摆动量要求在榫头底面涂尼龙胶，会使叶片自振频率有较大幅度下降；为排除3级叶片折断故障而提高的慢车转速又缩小了4级叶片的共振裕度，结果造成少数4级叶片落入慢车共振。共振发生时，不规则的尼龙胶和装配过程不规范引起的非正常接触容易导致微动磨损的加剧，从而大大降低了疲劳寿命，这是引起榫头断裂故障的主要原因。     

细观力学有限元法预测复合材料宏观有效弹性模量

基于能量等效原理提出了复合材料有效弹性模量的定义，并指出了该定义的基础及前提条件。为从理论上计算复合材料宏观有效弹性模量，建立了通过细观力学有限元法计算复合材料有效弹性模量的方法。复合材料宏观弹性模量，是通过对复合材料细观结构代表性体积元的力学响应的计算来得到，在该计算方法中，给出了施加简便的边界载荷以及恰当的边界变形约束条件的方法。数值计算结果与部分试验结果具有较好的一致性，表明所提出的方法能够较好地计算复合材料的宏观有效弹性模量。     

航空发动机电子控制器可测试性技术应用研究

基于边界扫描的测试思想,提出了1种航空发动机电子控制器可测试性设计方案。通过器件管脚的边界扫描单元,在板级甚至多个目标板组成的复杂系统间,构建了1条在集成电路边界绕行的移位寄存器链,可以实现复杂集成电路的嵌入式测试。该方案还可以实现故障注入,对航空发动机电子控制器机内自测试(B IT)能力进行验证。     

燃气二次喷射推力矢量控制系统启动过程非定常效应研究

采用数值模拟方法对燃气二次喷射推力矢量控制系统启动过程中非定常效应进行了研究.给出了详细的喷流瞬态干扰流场结构, 以及喷流瞬态干扰区随时间改变的流场细节特性,分析了流动参数和发动机内弹道性能的动态变化过程.研究表明,主/次流干扰流场内流动参数的分布及变化呈现复杂的多样性,启动过程中所呈现出的动态特性与系统稳定工作时有着明显的差异,侧向控制力、燃烧室平衡压强和发动机推力均有显著变化.在飞行器设计中,必须从安全控制的角度出发,考虑这一非定常效应的影响.     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.