潜射导弹级间段密封圈动态密封性能模拟试验方法

根据潜射导弹级间段密封圈在出水过程中的动态变形参数设计了一套模拟试验件和加载、加水及测量装置,采用摆锤冲击加载方式和裂纹动态张开位移测量方法再现了密封圈在导弹出水过程中的使用条件,证明密封圈在规定的开缝宽度、开缝时间和弹体内外压差的使用环境下能够保证防水和密封效果。利用两自由度冲击响应模型分析了试验的动响应曲线,给出了试验系统模态参数的识别结果。     

金属板料的激光冲击变形分析及其实验研究

介绍了激光冲击变形机理和冲击波产生原因,并建立了激光冲击下的板料变形模型,且推导了板料变形量计算公式。根据爆轰波和爆炸气体动力学理论,建立了激光冲击成形中激光-能量转换体-靶材系统爆轰波压力的估算式,并根据冲击波压力估算式估算所需激光脉冲能量,从而探讨了板料变形与激光能量、冲击波压力之间的关系,并进行实验研究。实验结果表明,板料厚度对变形量的影响与变形理论模型的分析基本相同,其变形量随厚度的增加而呈指数曲线减小,其轮廓形状也由小圆锥形逐渐向小球冠状变化。     

扰流环对粉末发动机燃烧流动影响的数值模拟

为了提高粉末火箭发动机的燃烧效率,通过数值模拟方法研究了扰流环的有无、通径及位置对燃烧室燃烧流动特性的影响。结果表明:扰流环会增强Al颗粒和气相的掺混和换热程度,促进Al颗粒蒸发和燃烧,从而提高粉末火箭发动机的燃烧效率。当扰流环通径比在0.538~0.846范围内时,扰流环的通径越小,燃烧效率越高;当扰流环头部距离比在0.3~0.8范围内时,扰流环位置离头部越近,燃烧效率越高。设计扰流环时,应在距离燃烧室头部30%~40%的位置布置小通径的扰流环。      

TC2薄壁钣金异型环快速制造工艺

对某种柔性的薄壁TC2钛合金异型环,传统的制造工艺由下料、拼焊、成形、机械加工、表面处理等工序组成。针对该工艺流程繁复、制造成本高的问题,提出一种不用成形的快速制造方法。该方法利用异形环平直母线可精确展开的特征,对其不同半径的锥面逐步展开后合理叠加成精确的展开图形,依图形下料并对焊成环。此方法仅需下料和焊接,无需成形和机械加工,流程简单,为该类零件的低成本、快速制造提供了新途径。     

Effect of protrusion amount on gas ingestion of radial rim seal

In this paper, the effect of different amount of protrusion on various parameters in rotor–stator system was experimentally studied by measuring CO₂ concentration and pressure, in order to obtain the optimal protrusion amount. The parameters of different dimensionless sealing flow were measured under the condition that the annulus Reynolds number was 4.39 × 10⁵ and the rotating Reynolds number was 1.05 × 10⁶. The results show that the change of the amount of protrusions has little effect on the static pressure in the cavity, and the static pressure change near the sealing ring is almost negligible. But the total pressure and sealing efficiency increase first and then decrease with the increase of the amount of protrusion. The variation of power consumption is the same. A complex vortex structure will appear at the high radius region when the protrusion is installed. On the other hand, the protrusion can effectively reduce the minimum sealing flow of the rotor–stator cavity. Furthermore, considering the sealing efficiency and power consumption, the best range of the protrusion amount is about 36. The ratio near this range can optimally balance the alleviation of the gas ingestion and the reduction of the power consumption.     

拓扑优化方法在航空用钣金零件设计中的应用

为了满足航空产品高载重量及低耗油率的要求,采用拓扑优化技术对航空用钣金零件进行结构优化,实现了钣金零件强度高和重量轻的指标.案例分析表明,在航空用钣金零件初始设计阶段引入拓扑优化方法,会比设计过程中单纯使用结构尺寸优化和形状优化获得更大的经济效益.     

机载电子设备搭接技术研究

针对机载电子设备装机时的搭接环节,对机箱主要搭接技术进行了研究。根据设备搭接目的和性能要求,给出了相应的设备-托架、托架-安装支架之间的搭接方法,模块-机柜、机柜-安装支架之间的搭接方法,以及设备的备份搭接方法,并指出了各种搭接方式的特点、优点和不足,为设备的研制和机上安装提供搭接技术支持。     

300 MVA脉冲发电机组滑差方式起动过程研究

介绍了300 MVA脉冲发电机组的滑差装置。对机组采取滑差方式的起动过程进行了分析和等效建模。根据机组实际起动过程电气波形,利用非线性规划模型,建立了滑差装置液体电阻等效仿真模型,并代入机组参数对起动过程进行仿真,仿真结果和实际波形吻合,验证了模型的正确性。在此基础上,为了使机组的转速达到额定转速,提出在滑差装置液体电阻低位时并入两级固体金属电阻后短接的方案,给出了两级固体金属电阻的阻值等理论参数,并通过仿真验证了方案的可行性。建立的仿真模型可以作为研究不同参数、不同控制策略下的机组起动过程动态特性的重要工具。     

非线性能量阱对飞轮振动抑制效果的实验研究

利用薄片金属梁作为非线性刚度元件，构建一种非线性能量阱。为了验证非线性能量阱对飞轮振动特性的抑制效果，搭建地面飞轮测试系统。分别采用力锤敲击和飞轮以恒定转速运行的方法施加不同载荷，对安装非线性能量阱前后测试系统各典型位置的振动响应进行对比研究。利用实测数据，采用傅里叶变换方法将动态响应信息分别在时间域和频率域内展开。研究表明：力锤敲击产生的冲击载荷和飞轮以恒定转速运行产生的稳态载荷均可以激发非线性能量阱定向能量传输；受非线性能量阱的影响，柔性支架设备安装面和飞轮安装面振动响应得到有效抑制。但是，由于非线性能量阱阻尼和吸振子质量较小，不同程度削弱了其振动抑制效果。     

Flow mechanism between purge flow and mainstream in different turbine rim seal configurations

The rim seal is used to prevent mainstream ingestion to the gap between the vane of a turbine and its blade. In this article, the dolphin lip with a hook configuration and a large seal cavity with hook structures are designed based on the high-pressure turbine datum single shark lip rim seal configuration. The sealing effect and parameters of the flow field are measured by an experiment method and a numerical simulation is used to explain the mechanism. For three configurations, the effect of the leakage slot vortex on the efficiency of the seal and the influence of leakage vortex, generated by the interaction between purge flow and mainstream flow, are discussed in depth. The result shows that the reverse vortex formed by the dolphin lip rim seal with hook structure will increase the sealing efficiency. The seal configuration with a large cavity improves sealing efficiency to a greater extent than the datum structure. At different purge flow rates and with unequal seal structures, the purge flow produces three types of leakage vortices in the passage. Besides, the seal configuration with dolphin lip produces a Kelvin-Helmholtz instability at the interface of the purge and the mainstream flows at a low purge flow rate to induce new leakage vortex branches in the passage of the blade.