全文获取类型
收费全文 | 1097篇 |
免费 | 295篇 |
国内免费 | 192篇 |
专业分类
航空 | 1113篇 |
航天技术 | 175篇 |
综合类 | 115篇 |
航天 | 181篇 |
出版年
2024年 | 3篇 |
2023年 | 17篇 |
2022年 | 60篇 |
2021年 | 71篇 |
2020年 | 78篇 |
2019年 | 71篇 |
2018年 | 71篇 |
2017年 | 106篇 |
2016年 | 82篇 |
2015年 | 83篇 |
2014年 | 92篇 |
2013年 | 96篇 |
2012年 | 91篇 |
2011年 | 105篇 |
2010年 | 64篇 |
2009年 | 73篇 |
2008年 | 56篇 |
2007年 | 71篇 |
2006年 | 44篇 |
2005年 | 34篇 |
2004年 | 36篇 |
2003年 | 29篇 |
2002年 | 23篇 |
2001年 | 16篇 |
2000年 | 15篇 |
1999年 | 11篇 |
1998年 | 8篇 |
1997年 | 9篇 |
1996年 | 7篇 |
1995年 | 11篇 |
1994年 | 12篇 |
1993年 | 5篇 |
1992年 | 10篇 |
1991年 | 6篇 |
1990年 | 9篇 |
1989年 | 5篇 |
1988年 | 1篇 |
1986年 | 3篇 |
排序方式: 共有1584条查询结果,搜索用时 15 毫秒
81.
A new type of aluminum lithium alloy (Al-Li alloy) Al-Li-S-4 was investigated by test in this paper. Alloy plate of 400 mm · 140 mm · 6 mm with single edge notch was made into samples bonded with Ti-6Al-4V alloy (Ti alloy) strap by FM 94 film adhesive after the surface was treated. Fatigue crack growth of samples was investigated under cyclic loading with stress ratio (R) of 0.1 and load amplitude constant. The results show that Al-Li alloy plate bonded with Ti alloy strap could retard fatigue crack propagation. Retardation effect is related with width and thickness of strap. Flaws have an observable effect on crack propagation direction. 相似文献
82.
分析了矩形截面管道气流中横向运动颗粒的运动轨迹及碰壁条件,研究表明颗粒飞出的临界速度随着颗粒直径的增大而减小,当颗粒直径较小时受来流密度、马赫数影响较大,总趋势是来流密度、马赫数越大,颗粒越不容易与上壁面碰撞。但随着颗粒直径的增大,来流条件对颗粒是否碰壁的影响逐渐减弱,决定因素是颗粒直径的大小和颗粒的喷射速度。 相似文献
83.
84.
85.
86.
二级轻气炮发射的氘冰弹丸的速度、质量和显示弹丸完整性的方法和所使用的仪器以及新开发的以波长编码、用光纤为传感器的弹丸进入位置的测量方法。 相似文献
87.
反推状态下大涵道比涡扇发动机气动稳定性预测与评估 总被引:3,自引:1,他引:3
为了预测与评估反推状态下,反推气流再吸入对大涵道比涡扇发动机气动稳定性的影响,采用反推气流扰流流场三维CFD数值模拟、发动机整机稳定性计算分析以及反推状态下发动机进气畸变台架试验相结合的方法,开展了反推气流对大涵道比涡扇发动机气动稳定性影响的研究。通过三维CFD数值模拟手段,捕获了反推状态下发动机进口流场的畸变程度。在此基础上,通过采用稳定性计算程序预测了发动机的气动稳定性,并进一步通过发动机台架试验,验证了预测结果。CFD计算结果表明,随着相对来流马赫数的减小,反推气流被发动机重新吸入的可能性不断增大,当相对来流马赫数减小到0.05时,外侧发动机进口的流场畸变情况变得最为严重。进气畸变情况下的整机稳定性计算分析以及发动机台架试验结果表明,在所考核的目标状态,若只存在因反推气流再吸入引起的进口流场畸变,是不会导致发动机失稳的。 相似文献
88.
89.
90.
Rotating experimental investigations were carried out to study the oil sealing capability of two different floating ring seals in cold/hot state for aero-engine. High-speed Floating Ring Seal(HFRS) is a seal with the inner diameter of 83.72 mm and maximum speed of 38000 r/min, and Low-speed Floating Ring Seal(LFRS) is another seal with the inner diameter of 40.01 mm and maximum speed of 18000 r/min. In hot state, sealing air with the temperature of 371 K and oil with the temperature of 343 K was employed to model the working conditions of an aero-engine. Comparisons between floating ring seal and labyrinth seal were done to inspect the leakage performance.More attention was paid to the critical pressure ratio where the oil leakage began. Results show that the critical pressure ratio in cold state is obviously larger than that in hot state for both seals. An underlying sealing mechanism for floating ring seal is clarified by the fluid film, which closely associates with the dimensionless parameter of clearance over rotating diameter(2 c/Dr). Another fantastic phenomenon is that the leakage coefficient in hot state, not the leakage magnitude, is unexpectedly larger than that in cold state. Overall, the leakage performance of the floating ring seal is better than the labyrinth seal. 相似文献