无刷直流电机霍尔传感器安装方法研究

针对有位置传感器的无刷直流电机需要位置传感器提供换相信号的问题, 提出了基于磁势确定霍尔传感器安装位置的方法。霍尔传感器通过检测转子磁势确定转 子位置,产生传感器信号控制定子绕组换相,使得定、转子磁势相位差在60°~120°之间 波动,从而使电机输出最大力矩。通过实验测得使用该方法进行霍尔传感器位置安装的 无刷直流电机的输出力矩波形与理论一致,从而验证了此方法正确可行。     

离子与霍尔电推进性能和质量的工程数据模型

为了提供航天工程任务设计时优选离子或霍尔电推进的通用对比分析方法,基于工程数据建立了包括推力器、电源处理单元、推力器选择单元、控制单元、推进剂气瓶、调压单元、流率单元、推力器支架、电缆、管路等产品的电推进的性能和质量经验模型。在此基础上通过推导建立了电推进系统干质量通用模型,模型变量参数包括推力器功率、推力器数量和推进...     

平板湍流摩阻系数的显式表达式

 湍流摩阻系数的计算是工程技术中经常遇到的问题。计算时所依据的公式多为半经验半理论的结果,如Karman公式,Van Driest公式和Prandtl公式等。这些公式是以隐函数给出的,给计算带来不便。但是不难发现,这类公式经过适当的变换,可以化为统一形式的超越代数方程,这种方程没有有限形式的解析解,本文给出了一种近似解析解。根据这种方法除了导出上述公式的显式表达式外,还对White公式作了修正。当然解超越代数方程最根本的方法是迭代法,本文对此也作了简单讨论。     

平板上钝缘舵在超声速绕流中的三维分离特性研究

对于平板上的直立钝缘舵在M_∞=1.79、2.04和2.50的条件下,研究了该平板干扰区中的三维分离特性。着重讨论了钝缘直径、舵面迎角和来流马赫数对主分离线位置和形状的影响。分析了该类三维分离在性态上更强地依赖于无粘流动特性。此外,还对分离区内的二次分离发展过程和形态进行了初步讨论。     

Multi-channel discharge characteristics cutting by ultra-fine wire-EDM

Compared with a copper wire electrode, molybdenum wire with a poor conductor is usually used as the electrode in high speed wire-cut electrical discharge machining(HSWEDM), so the resistance of an ultra-fine wire cannot be ignored. To study the differences of discharge characteristics between the ultra-fine wire and the conventional diameter wire, the continuous discharge waveform of two kinds of wire electrodes was compared. It was found that there was a multichannel discharge phenomenon in the...     

翼身融合运输机分布式电推进系统设计及油耗评估

针对翼身融合运输机开展了分布式电推进系统的总体设计与油耗评估。通过数值计算完成了70t载质量翼身融合飞机的气动设计与优化。在巡航马赫数为0.80和10km高度的设计点,最大升阻比达到了24。通过求解积分边界层方程组,完成了电推进系统的总体设计。电推进系统包含10个推进风扇,风扇直径为1.45m，压比为1.35，巡航功率为2.94MW。建立了考虑燃烧过程的发动机一维性能模型,对发动机油耗进行了评估,获得了不同发动机循环参数下燃油消耗。建模结果表明,基于翼身融合布局和分布式电推进技术,可使运输机的油耗较C-17节省近50%。      

Case study of inclined sporadic E layers in the Earth’s ionosphere observed by CHAMP/GPS radio occultations: Coupling between the tilted plasma layers and internal waves

We have used the radio occultation (RO) satellite data CHAMP/GPS (Challenging Minisatellite Payload/Global Positioning System) for studying the ionosphere of the Earth. A method for deriving the parameters of ionospheric structures is based upon an analysis of the RO signal variations in the phase path and intensity. This method allows one to estimate the spatial displacement of a plasma layer with respect to the ray perigee, and to determine the layer inclination and height correction values. In this paper, we focus on the case study of inclined sporadic E (E_s) layers in the high-latitude ionosphere based on available CHAMP RO data. Assuming that the internal gravity waves (IGWs) with the phase-fronts parallel to the ionization layer surfaces are responsible for the tilt angles of sporadic plasma layers, we have developed a new technique for determining the parameters of IGWs linked with the inclined E_s structures. A small-scale internal wave may be modulating initially horizontal E_s layer in height and causing a direction of the plasma density gradient to be rotated and aligned with that of the wave propagation vector k. The results of determination of the intrinsic wave frequency and period, vertical and horizontal wavelengths, intrinsic vertical and horizontal phase speeds, and other characteristics of IGWs under study are presented and discussed.     

展向离散抽吸法控制边界层转捩实验研究

通过实验成功发展了一种生成大振幅稳定条带的有效方法,即展向离散抽吸方法。在此基础上,开展条带控制边界层转捩的研究。实验在水洞中进行,以零压力梯度平板边界层为研究对象,利用氢气泡时间线法观测引入条带前后人工激发转捩边界层中扰动发展变化,分析条带对转捩的控制效果及参数影响。结果表明,展向离散抽吸方法生成的稳定条带最大振幅可达28.4%U（U为自由流速度）;实验中引入的宽度14和28mm的稳定条带都能起到抑制转捩的作用;条带振幅越大、宽度越窄,抑制效果越明显。研究结果为探索降低水/空气中航行器摩阻的新技术提供有价值的参考。     

Streamwise vortex generation by the rod

The technology development related to aerodynamics is leading to ever increasing loads of wings, airfoils and turbine and compressor blades. The increase in aerodynamic forces is often leading to flow separation and depreciation of the aerodynamic performance of flying objects or propulsion systems. Flow control methods are required to avoid these negative effects. In the recent two decades the flow control by means of air-jet vortex generators has been also intensively investigated. In this method a streamwise vortex is introduced by an oblique jet. The necessity to supply air by a pipe system may be considered a disadvantage. In order to eliminate this feature, it has been proposed to put out a rod instead of a jet. It has been shown that the application of a rod can introduce the same effect as a jet, as long as the streamwise vortex generation is concerned and appropriate dimensions are used. The present paper focuses on the influence of rod vortex generators on a flow pattern downstream. The results presented here concern experimental and numerical investigations and provide guidelines for the design of a new flow control method dedicated mainly to external flows.     

带轴对称台阶的圆锥高超声速边界层转捩试验

在Ma 6风洞内，通过高频脉动压力测试技术和基于纳米粒子示踪的平面激光散射(NPLS)技术，分别对带前向、后向轴对称台阶的圆锥高超声速边界层转捩进行了试验研究。采用功率谱密度分析和互相关计算等方法对脉动压力数据进行分析，得到了边界层中扰动波的发展规律，定量分析了第二模态波的相关参数。结果显示：两种模型中第二模态波在沿流向向下游发展的过程中，其幅值均先增大再衰减、特征频率均逐渐减小；特征频率和传播速度整体上均随雷诺数的增大而增加(后台阶模型中特征频率由100 kHz增至196 kHz，前台阶中则由 97 kHz 增至174 kHz)、波长变化规律则与之相反(后台阶中由6.35 mm降至4.54 mm，前台阶由7.35 mm降至 4.66 mm )；后台阶模型中第二模态波初次出现位置比前台阶中更靠近上游，边界层转捩位置较前台阶前移。将NPLS结果与高频脉动压力测试结果进行对比，两者吻合较好。