飞机机翼着陆滑跑动态性能分析

飞机着陆滑跑过程中,机翼结构将受到较大的冲击作用和振动激励。为预判结构局部危险部位,给结构强度设计提供参考,需对机翼着陆滑跑过程中的动态性能进行分析。创新性地考虑了飞机滑跑速度和气动力的变化,为有限元计算提供可靠的外载输入,并合理设置约束条件,建立半机体有限元模型,降低计算规模。最后提取机翼各站位处的载荷响应峰值,做出动响应包线,预判结构局部危险部位,如机翼根部,为结构强度设计提供参考。     

进气道内压缩比对固体燃料超燃冲压发动机性能的影响

为研究固体燃料超燃冲压发动机进气道与燃烧室的匹配特性,以飞行马赫数为6、飞行高度为25km为设计点对发动机各部件进行初步设计,采用数值模拟方法计算了一系列具有不同进气道内收缩比的发动机模型.结果表明:在保持燃烧室结构不变的条件下,发动机推力与比冲随进气道内压缩比增大开始显著下降,随后小幅上升;在保持燃烧室入口面积扩张比不变的条件下,发动机总体性能随进气道内收缩比的增大而提高.在满足进气道起动与燃烧室火焰稳定的前提下,发动机设计应采用尽可能大的进气道内收缩比与尽可能小的燃烧室入口面积扩张比.      

叶片反扭对跨声速大涵道比风扇性能的影响

使用基于流固耦合算法的叶片反扭程序,考虑了非定常气动力对叶片变形的非线性作用,研究了叶片反扭对跨声速大涵道比风扇性能的影响.以冷态叶型为起点,先计算离心力作用下的叶片变形,在此基础上使用流固耦合程序获得非定常气动力作用下的变形.考察了3个转速下叶片的动态变形对大涵道比风扇气动性能的影响.结果表明:在跨声速工况下,叶片表面激波位置的变化对叶片反扭角有很大作用,在考察的转速范围内,堵塞点使用设计叶型计算的流量大于动态叶型下的流量,数值达7%,将导致发动机起飞推力小于预测值.结果表明在大涵道比风扇设计阶段,预测气动性能使用准确叶型的重要性.      

多喷嘴构型的轴对称氢氧加热器设计与仿真

为了使氢氧燃烧加热器满足自由射流试验台工作需要并获得均匀的出口气流参数,采用同轴剪切式7个喷嘴轴对称构型喷注器,利用CFD仿真软件对其进行了三维反应流场计算,燃烧模型采用氢氧单步反应模型,获得了设计工况下的参数.计算结果表明:燃烧效率随着中心喷嘴与外围喷嘴距离L与喷注面板半径R之比(L/R)的增大先上升后下降;喷注面板的温度随着L/R的增大而降低,最终维持在600K左右;加热器出口的氧气摩尔分数以及总温的均匀性基本不随着L/R变化而变化;出口主流区的马赫数在6左右满足设计要求.在各个喷嘴的影响区域大致相等时,加热器综合性能良好.氢氧速度比越大,完全燃烧所需区域越短,喷注面板温度越高.与单喷嘴、19个喷嘴的加热器比较发现7个喷嘴的构型较为合理.      

后掠翼三维鼓包串激波控制参数的影响

针对跨声速后掠翼,三维鼓包串作为一种有效的减阻方式具有结构简单、高效及鲁棒性好等优点.利用全局优化算法探索了鼓包设计参数空间的整体特性,并对鼓包长度、三维鼓包展向设计参数对鼓包减阻效果的影响进行了研究,发现鼓包顶点位置和高度对阻力系数最敏感,三维鼓包的展向设计参数则对阻力系数不敏感,而鼓包长度和鼓包相对展长越长越有利于减阻.在此基础上开展了小后掠角自然层流机翼加3种不同类型鼓包串的优化研究,通过优化结果发现,增加优化后的三维鼓包串,可将小后掠角自然层流机翼阻力发散马赫数向后推移,并且鼓包平均长度和控制区越大,效果越好.三维鼓包串具有良好的局部控制特性,可用于局部较强激波的抑制.三维鼓包串对常规后掠翼波阻具有良好的控制效果,同时能够抑制激波诱导的机翼后缘气流分离.      

毫秒脉冲等离子体激励改善飞翼的气动性能实验

在来流速度为30m/s时,进行了毫秒脉冲介质阻挡放电等离子体激励改善飞翼气动性能的风洞实验.等离子体激励器布置在飞翼前缘,峰峰值电压为9.5kV时,放电的脉冲能量在0.1mJ/cm量级.通过六分量测力天平测力研究了脉冲激励频率和占空比对升/阻力系数、升阻比和俯仰力矩系数的作用效果.结果表明:等离子体激励可以有效改善飞翼大攻角气动特性;在最佳无量纲脉冲激励频率F+≈1时,临界失速迎角由14°提高到17°,最大升力系数提高10%;占空比对流动控制效果影响较大,减小占空比可以降低能耗,实验中最佳占空比为5%;俯仰力矩系数的变化表明施加等离子体激励改善了飞翼纵向静稳定性.      

Flapping wing micro-aerial-vehicle:Kinematics,membranes, and flapping mechanisms of ornithopter and insect flight

The application of biomimetics in the development of unmanned-aerial-vehicles (UAV) has advanced to an exceptionally small scale of nano-aerial-vehicles (NAV), which has surpassed its immediate predecessor of micro-aerial-vehicles (MAV), leaving a vast range of development possi-bilities that MAVs have to offer. Because of the prompt advancement into the NAV research devel-opment, the true potential and challenges presented by MAV development were never solved, understood, and truly uncovered, especially under the influence of transition and low Reynolds number flow characteristics. This paper reviews a part of previous MAV research developments which are deemed important of notification; kinematics, membranes, and flapping mechanisms ranges from small birds to big insects, which resides within the transition and low Reynolds number regimes. This paper also reviews the possibility of applying a piezoelectric transmission used to pro-duce NAV flapping wing motion and mounted on a MAV, replacing the conventional motorized flapping wing transmission. Findings suggest that limited work has been done for MAVs matching these criteria. The preferred research approach has seen bias towards numerical analysis as com-pared to experimental analysis.     

Streamwise-body-force-model for rapid simulation combining internal and external flow fields

A streamwise-body-force-model (SBFM) is developed and applied in the overall flow simulation for the distributed propulsion system, combining internal and external flow fields. In view of axial stage effects, fan or compressor effects could be simplified as body forces along the streamline. These body forces which are functions of local parameters could be added as source terms in Navier-Stokes equations to replace solid boundary conditions of blades and hubs. The val-idation of SBFM with uniform inlet and distortion inlet of compressors shows that pressure perfor-mance characteristics agree well with experimental data. A three-dimensional simulation of the integration configuration, via a blended wing body aircraft with a distributed propulsion system using the SBFM, has been completed. Lift coefficient and drag coefficient agree well with wind tun-nel test results. Results show that to reach the goal of rapid integrated simulation combining inter-nal and external flow fields, the computational fluid dynamics method based on SBFM is reasonable.     

Dynamic modeling and analysis of vortex filament motion using a novel curve-fitting method

Applications of a novel curve-fitting technique are presented to efficiently predict the motion of the vortex filament, which is trailed from a rigid body such as wings and rotors. The governing equations of the motion, when a Lagrangian approach with the present curve-fitting method is applied, can be transformed into an easily solvable form of the system of nonlinear ordinary differential equations. The applicability of Be′zier curves, B-spline, and Lagrange interpolating polynomials is investigated. Local Lagrange interpolating polynomials with a shift operator are proposed as the best selection for applications, since it provides superior system characteristics with minimum computing time, compared to other methods. In addition, the Gauss quadrature formula with local refinement strategy has been developed for an accurate prediction of the induced velocity computed with the line integration of the Biot–Savart law. Rotary-wing problems including a vortex ring problem are analyzed to show the efficiency, accuracy, and flexibility in the applications of the proposed method.     

Gust response analysis and wind tunnel test for a high-aspect ratio wing

A theoretical nonlinear aeroelastic response analysis for a flexible high-aspect ratio wing excited by harmonic gust load is presented along with a companion wind tunnel test. A multidisci-plinary coupled numerical calculation is developed to simulate the flexible model wing undergoing gust load in the time domain via discrete nonlinear finite element structural dynamic analysis and nonplanar unsteady vortex lattice aerodynamic computation. A dynamic perturbation analysis about a nonlinear static equilibrium is also used to determine the small perturbation flutter bound-ary. A novel noncontact 3-D camera measurement analysis system is firstly used in the wind tunnel test to obtain the spatial large deformation and responses. The responses of the flexible wing under different static equilibrium states and frequency gust loads are discussed. The fair to good quanti-tative agreements between the theoretical and experimental results demonstrate that the presented analysis method is an acceptable way to predict the geometrically nonlinear gust response for flex-ible wings.