大迎角下鸭翼涡与边条涡的干扰特性

 在风洞测力、水洞染色线和激光片光实验的基础上 ,对翼身组合体鸭翼边条翼布局大迎角涡系干扰机理进行了分析和探讨 ,揭示了该布局增升的机理。鸭翼涡位于机翼内侧 ,其与边条涡的相互诱导致使边条涡向外翼偏折 ,既改善了外翼的流态 ,又使机翼前缘涡量卷入边条涡 ,增强了边条涡的强度 ,从而延迟其破裂。两方面的共同作用 ,提高了主翼的涡升力 ,起到增升作用。     

三维瞬态导热温度场边界元计算及一阶数学奇异的处理

推导了三维瞬态导热温度场边界元解法的积分方程和离散代数方程，并编制了相应的计算机程序，采用坐标变换的解析消去法，处理边界元的一阶数学奇异点，从而提高了算法的数值精度。用本程序计算了正方体和圆柱环瞬态导热温度场，数值解与解析解的吻合程度令人满意。     

喷口辐射热泄漏对延伸段壁温分布的影响

引入喷口的热辐射泄漏损失，导出辐射冷却推力室壁温的计算方程。分析表明，考虑与不考虑喷口热损失二者相比较，前者壁温约下降７０℃。本结果可为喷管延伸段材料的选取提供更为科学的理论依据。     

F-16飞机大迎角飞行偏离/尾旋特性分析

通过俯仰力矩系数随迎角的变化对F－16飞机的气动特性进行分析，并对其中大迎角时的偏离特性进行了剖析，通过计算给出了F－16飞机的m^βx,m^βy,m^δy,m^δyx,m^δyy,m^δyxy以及侧滑偏离参数（m^βydyn)和横向操纵偏离参数（LCDP）随迎角的变化曲线，最后通过m^βydyn和LCDP的综合，预测了F－16飞机的偏离特性，同时通过计算对尾旋运动特性和改出特性进行了研究，为分析F－16飞机大迎角飞行特性提供了理论依据。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

热处理对二次锻造高Nb-TiAl基合金组织的影响

研究了热处理对二次锻造高Nb-TiAl基合金组织的影响。通过对Ti-45Al-9(Nb,W,B,Y)金属间化合物进行不同的热处理,得到不同的显微组织。结果表明,经1310℃/20min+1250℃/2h/AC热处理后,β相被有效地消除,得到细小均匀的双态组织。此后直接加热到α单相区,得到条带状的全片层组织。增加在两相区的停留,得到相对比较均匀细小的全片层组织。将锻造组织先转变为近γ组织再进行全片层组织处理,得到最均匀细小的全片层组织。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

两种中温固化胶粘剂的剪切疲劳和蠕变性能研究

研究了SY 2 4B胶膜和SY H2糊状胶粘剂的剪切疲劳和蠕变性能。SY 2 4B胶膜和SY H2糊状胶粘剂同为中温固化的结构胶粘剂 ,SY 2 4B胶膜采用橡胶增韧 ,SY H2糊状胶粘剂采用热塑性树脂增韧。SY 2 4B胶膜虽然具有优异的韧性 ,但SY H2糊状胶粘剂的剪切疲劳和蠕变性能优于SY 2 4B胶膜 ,这与增韧剂种类与胶层厚度有一定关系。温度、应力和时间也是影响蠕变量的重要因素     

大攻角流动的非定常特性分析

本文首先通过动态测量手段研究了大攻角流场中的能量成分,分析了各种成分引发的非定常性对大攻角流动的影响。结果表明大攻角流动本身是一种“涡行为”,非定常性对大攻角流动非对称性的影响较弱,影响大攻角流动的本质因素是涡的动力不稳定性对于前体不确定小扰动的响应。     

TC6钛合金棒材热处理工艺研究

对TC6钛合金φ20mm～φ120mm不同规格棒材进行了普通退火、双重退火、等温退火、固溶时效等热处理方法和热处理制度研究,并对比分析了热处理制度和组织、性能之间的影响关系,结果表明,TC6钛合金的组织和性能对热处理工艺敏感,应根据半成品规格、类型、截面形状、使用温度、受力情况以及设备条件等诸多因素选择合适的热处理方法和制度,才能达到强度、塑性和韧性的最佳匹配。研究结果证实普通退火是一种简单易行的退火制度,适用于飞机结构用中等规格棒材等半成品的退火,进一步提出了TC6钛合金棒材的热处理工艺选择原则。