喷口辐射热泄漏对延伸段壁温分布的影响

引入喷口的热辐射泄漏损失，导出辐射冷却推力室壁温的计算方程。分析表明，考虑与不考虑喷口热损失二者相比较，前者壁温约下降７０℃。本结果可为喷管延伸段材料的选取提供更为科学的理论依据。     

F-16飞机大迎角飞行偏离/尾旋特性分析

通过俯仰力矩系数随迎角的变化对F－16飞机的气动特性进行分析，并对其中大迎角时的偏离特性进行了剖析，通过计算给出了F－16飞机的m^βx,m^βy,m^δy,m^δyx,m^δyy,m^δyxy以及侧滑偏离参数（m^βydyn)和横向操纵偏离参数（LCDP）随迎角的变化曲线，最后通过m^βydyn和LCDP的综合，预测了F－16飞机的偏离特性，同时通过计算对尾旋运动特性和改出特性进行了研究，为分析F－16飞机大迎角飞行特性提供了理论依据。     

内爆炸圆管破片初速研究

分析内爆炸圆管膨胀破碎过程的应力,提出确定内爆炸圆管断裂半径的复合判据,从理论上预测不同材料圆管的破片初速度.采用GSJ高速摄影记录仪测试不同材料圆管的破片初速度,并与理论预测值行比较.结果表明,采用复合判据得到的理论预测结果与实验测量结果能够较好吻合.     

含内热源球壳的复合传热特性及其表面温度均匀性研究

应用计算流体动力学方法,对带内热源的空腔球壳所涉及的含导热、自然对流和辐射换热的耦合传热问题进行了数值建模,得到了球壳空腔内、外侧流体的温度场、速度场。在数值模拟基础上,提出并试验验证了能有效提高球壳外表面温度均匀性的电加热绳方案。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

热处理对二次锻造高Nb-TiAl基合金组织的影响

研究了热处理对二次锻造高Nb-TiAl基合金组织的影响。通过对Ti-45Al-9(Nb,W,B,Y)金属间化合物进行不同的热处理,得到不同的显微组织。结果表明,经1310℃/20min+1250℃/2h/AC热处理后,β相被有效地消除,得到细小均匀的双态组织。此后直接加热到α单相区,得到条带状的全片层组织。增加在两相区的停留,得到相对比较均匀细小的全片层组织。将锻造组织先转变为近γ组织再进行全片层组织处理,得到最均匀细小的全片层组织。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

两种中温固化胶粘剂的剪切疲劳和蠕变性能研究

研究了SY 2 4B胶膜和SY H2糊状胶粘剂的剪切疲劳和蠕变性能。SY 2 4B胶膜和SY H2糊状胶粘剂同为中温固化的结构胶粘剂 ,SY 2 4B胶膜采用橡胶增韧 ,SY H2糊状胶粘剂采用热塑性树脂增韧。SY 2 4B胶膜虽然具有优异的韧性 ,但SY H2糊状胶粘剂的剪切疲劳和蠕变性能优于SY 2 4B胶膜 ,这与增韧剂种类与胶层厚度有一定关系。温度、应力和时间也是影响蠕变量的重要因素     

大攻角流动的非定常特性分析

本文首先通过动态测量手段研究了大攻角流场中的能量成分,分析了各种成分引发的非定常性对大攻角流动的影响。结果表明大攻角流动本身是一种“涡行为”,非定常性对大攻角流动非对称性的影响较弱,影响大攻角流动的本质因素是涡的动力不稳定性对于前体不确定小扰动的响应。     

Study on the breakup lengths of free round liquid jets

IntroductionBreakup and atomization of roundliquidjetshad been widely used in internal combustion en-gines,gas turbines,and liquid rocket engines.Recently,with the development of scramjet en-gines and the deepening of fuel atomization re-search,it attract…