联合应用现代优化方法与S2流面计算进行多级涡轮的气动设计

本文联合应用S2流面正问题计算和多级局部优化设计对某三级涡轮进行多级气动优化设计。优化联合采用人工神经网络和遗传算法,流场计算采用全三维粘性流N-S方程求解,计算网格采用H-O-H型网格,即入口段、出口段采用H型网格,叶片区域采用O型网格。通过优化,总效率提高1.1%,总体性能提高,达到设计要求。     

迟滞非线性二元机翼颤振特性分析

 采用多项式迟滞非线性模型建立二元机翼气动弹性运动方程，并用数值积分法进行求解。通过系统响应振幅随来流速度变化的分叉图和频谱分析发现，俯仰方向由于含有非线性因素，振动中的高阶分量随速度提高不断增加，并引起高次分叉。重点研究“机翼/空气”质量比以及“沉浮/俯仰”两个自由度的自然振动频率比对非线性颤振速度边界的影响，并提出可以通过提高自然振动频率比来减小迟滞非线性因素的不利影响。     

三维贴体坐标系下燃烧室热态流场的大涡模拟

大涡模拟三维贴体坐标系下环形燃烧室火焰简热态紊流瞬态流场。利用椭圆方程方法生成三维贴体网格，计算中采用k方程亚网格尺度模型估算亚网格紊流粘性；亚网格EBU燃烧模型估算化学反应速率；热通量辐射模型估算辐射通量。并在非交错网格系下采用sIMPLE算法和混合差分格式求解离散方程，利用壁面函数处理固壁边界条件。计算结果与实验结果的比较表明，采用大涡模拟方法能更真实反映环形燃烧室火焰简内紊流化学反应流气流结构和燃烧过程。     

大扭曲叶片整体涡轮电解加工工艺研究

研究用展成电解工艺进行大扭曲度整体涡轮叶片的机械加工，对涡轮叶片型面进行数据处理，用软件方式实现电解加工的多轴联动进给；分析叶片电解过程成形规律，合理设计阴极、流场，解决大扭曲叶片加工的叶背二次腐蚀、出口短路等关键工艺问题，试验可稳定达到工序精度要求，并可批量生产。     

F-16飞机大迎角飞行偏离/尾旋特性分析

通过俯仰力矩系数随迎角的变化对F－16飞机的气动特性进行分析，并对其中大迎角时的偏离特性进行了剖析，通过计算给出了F－16飞机的m^βx,m^βy,m^δy,m^δyx,m^δyy,m^δyxy以及侧滑偏离参数（m^βydyn)和横向操纵偏离参数（LCDP）随迎角的变化曲线，最后通过m^βydyn和LCDP的综合，预测了F－16飞机的偏离特性，同时通过计算对尾旋运动特性和改出特性进行了研究，为分析F－16飞机大迎角飞行特性提供了理论依据。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

热处理对二次锻造高Nb-TiAl基合金组织的影响

研究了热处理对二次锻造高Nb-TiAl基合金组织的影响。通过对Ti-45Al-9(Nb,W,B,Y)金属间化合物进行不同的热处理,得到不同的显微组织。结果表明,经1310℃/20min+1250℃/2h/AC热处理后,β相被有效地消除,得到细小均匀的双态组织。此后直接加热到α单相区,得到条带状的全片层组织。增加在两相区的停留,得到相对比较均匀细小的全片层组织。将锻造组织先转变为近γ组织再进行全片层组织处理,得到最均匀细小的全片层组织。     

脉冲爆震发动机工作过程控制和协调试验

利用开环控制系统,在直径180mm,长度2000mm,采用气动阀模拟飞行进气、燃用汽油的脉冲爆震发动机(PDE)样机上,对PDE的工作过程控制和协调进行了试验研究,得到了在不同的PDE工作过程时间分配下的试验结果,由此详细分析了在开环控制的情况下,PDE协调工作的条件及不能正常工作的原因,为PDE的设计和控制系统的研制提供重要的参考价值。     

气动参数对后台阶三维缝隙换热影响的研究

针对涡轮叶片尾缘冷却结构特点,建立了后台阶三维缝隙结构气膜冷却特性试验台,测量了缝隙中心和肋中心下游换热系数的局部分布,研究了不同雷诺数Re(5000~15000)与吹风比Br(0.5~2.0)对换热系数的影响规律,试验结果表明:(1)出口的换热系数总体呈下降趋势,但在肋后中心线略有起伏;(2)随着Re的增大,换热系数增大,随着Br的增大,换热系数减小;(3)在靠近出口位置,由于热边界层与三维掺混特性流场的影响,使得换热变得复杂。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.