飞机燃油测量方法研究

针对某机型油箱，利用切片法有效地求解了飞机在任意姿态下的燃油量及姿态误差，并尝试采用三维实体造型技术来进行飞机燃油的测量及误差分析。     

吸热型碳氢燃料催化裂解热沉测定

报道了一套高温下测量吸热型碳氢燃料催化裂解热沉的稳态热导型流动热量计，仪器常数标定结果线性关系良好，符合Tian’s方程，可以正常工作；测定了500℃和600℃下吸热型碳氢燃料RL7及NNJ-150在SAPO-34分子筛催化剂上的催化裂解热沉，并与相同条件下热裂解热沉相比较，结果表明，吸热型碳氢燃料在SAPO-34分子筛催化剂上发生催化裂解能够比热裂解获得更高的热沉，燃料吸热工作温度可降低100℃。     

地球非球形对卫星轨道的长期影响及补偿研究

首先建立了地球非球形引力摄动模型,通过对地球非球形引力摄动对卫星轨道的长期影响分析发现,地球非球形引力摄动对卫星轨道升交点赤经和沿迹角的漂移量与时间成近似线性关系;然后推导了通过主动偏置半长轴和倾角的方法来补偿摄动长期影响的计算公式,设计了基于仿真的地球非球形引力摄动补偿方法;最后对GlobalStar星座卫星进行仿真与试验.结果表明,设计的补偿方法是可行的,摄动补偿后在地球非球形引力摄动作用下卫星轨道的长期稳定性得到了很好的保持.     

非线性油膜支承裂纹转子振动特性分析

 以具有无限长轴承和无限短轴承支承的横向裂纹转子为研究对象,分析在非线性油膜力与横向裂纹联合作用时,Jeffcott转子的动力特性,并将其与刚性支承情况进行比较。结果表明轴承油膜力的存在对裂纹转子的振动影响较大,一般将降低转子的振动,这样势必增加转子裂纹故障诊断的难度。所以,在进行裂纹转子的故障诊断时,必须考虑到支承条件的影响,建立合理的动力学模型。     

气动参数对后台阶三维缝隙换热影响的研究

针对涡轮叶片尾缘冷却结构特点,建立了后台阶三维缝隙结构气膜冷却特性试验台,测量了缝隙中心和肋中心下游换热系数的局部分布,研究了不同雷诺数Re(5000~15000)与吹风比Br(0.5~2.0)对换热系数的影响规律,试验结果表明:(1)出口的换热系数总体呈下降趋势,但在肋后中心线略有起伏;(2)随着Re的增大,换热系数增大,随着Br的增大,换热系数减小;(3)在靠近出口位置,由于热边界层与三维掺混特性流场的影响,使得换热变得复杂。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

雾化槽喷嘴初始燃油雾化特性的研究

 <正> 1.试验方法 雾化槽是由槽形挡板和直流式喷嘴组成的一种气动式雾化喷嘴。本文将研究在雾化槽喷嘴下游25mm截面上的初始燃油雾化特性。 利用激光全息测量雾化槽喷嘴的油雾场。为了减小油滴密度过大对激光全息测量的影响,在同一瞬时拍摄油雾场不同空间层次油滴分布的2～3张全息记录干板。激光全息记录系统为同轴光路系统。油雾场再现处理时,直接利用摄象机把再现油滴摄入,并在监视器     

Kinetic Monte Carlo Simulation of EB-PVD Film:Effects of Substrate Temperature

The 2D kinetic Monte Carlo (KMC) simulation was used to study the effects of different substrate temperatures on the microstruc-ture of Ni-Cr films in the process of deposition by the electron beam physical vapor deposition (EB-PVD). In the KMC model, substrate was assumed to be a “surface” of tight-packed rows, and the simulation includes two phenomena: adatom-surface collision and adatom diffusion. While the interaction between atoms was described by the embedded atom method, the jumping energy was calculated by the molecular static (MS) calculation. The initial location of the adatom was defined by the Momentum Scheme. The results reveal that there exists a critical substrate temperature which means that the lowest packing density and the highest surface roughness structure will be achieved when the temperature is lower than the smaller critical value, while the roughness of both surfaces and the void contents keep decreasing with the substrate temperature increasing until it reaches the higher critical value. The results also indicate that the critical substrate temperature rises as the deposition rate increases.     

高密度喷气燃料与常规喷气燃料浓度场试验研究

本文利用ＣＯ２红外气体分析仪和取样管对高密度喷燃料和常规喷气燃料在直流喷嘴下游的浓度场分布进行了测量，就气流速度，油压降和下游距离对浓度场分布的影响进行了对比研究。试验结果表明，在相同工况下，常规喷气燃料的最大浓度值比高密度喷气燃料的大；气流速度和油压变化对高密度喷气燃料最大浓度点穿透深度的影响大于对常规喷气燃料的影响。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.