吸热型碳氢燃料RP-3替代模型研究

利用广义对应态法则对吸热型碳氢燃料RP-3的5种替代模型的密度、黏度、导热系数和比定压热容进行了数值计算.计算温度变化范围为300~800K,压力变化范围为3~6MPa.结果表明:不同替代模型均能定性重现RP-3在拟临界温度附近的物性急剧变化;由53%正十一烷,18%正丁基环己烷,29%1,3,5-三甲基苯组成的3组分替代模型在预测RP-3物性上表现最优,相对于实验数据,300~700K内密度相对误差均小于0.08;替代模型的相对分子质量越大,预测的拟临界温度越高,对拟临界温度下物性值的影响无显著规律.      

航空碳纤维树脂基复合材料加筋板压缩屈曲及后屈曲性能

开展了复合材料加筋板轴压稳定性实验,对加筋板的屈曲及后屈曲性能、破坏模式和后屈曲失效表征进行了研究.实验结果表明加筋板在轴压下具有良好后屈曲承载潜能,破坏载荷约为屈曲载荷的2.2倍;其屈曲模式为筋条间蒙皮首先发生屈曲失稳,筋条在整个承载过程中保持直线,起到“屈曲分隔”的作用.通过对加筋板屈曲及后屈曲性能的理论分析,得出的理论屈曲载荷和理论破坏载荷与实验结果相对误差均小于8%,并确定了在后屈曲过程中蒙皮中心挠度的变化规律和轴向载荷的面内分布特征.      

Dynamic modeling and analysis of vortex filament motion using a novel curve-fitting method

Applications of a novel curve-fitting technique are presented to efficiently predict the motion of the vortex filament, which is trailed from a rigid body such as wings and rotors. The governing equations of the motion, when a Lagrangian approach with the present curve-fitting method is applied, can be transformed into an easily solvable form of the system of nonlinear ordinary differential equations. The applicability of Be′zier curves, B-spline, and Lagrange interpolating polynomials is investigated. Local Lagrange interpolating polynomials with a shift operator are proposed as the best selection for applications, since it provides superior system characteristics with minimum computing time, compared to other methods. In addition, the Gauss quadrature formula with local refinement strategy has been developed for an accurate prediction of the induced velocity computed with the line integration of the Biot–Savart law. Rotary-wing problems including a vortex ring problem are analyzed to show the efficiency, accuracy, and flexibility in the applications of the proposed method.     

大型飞机迎角保护控制律设计及试飞技术研究

针对大型飞机迎角保护控制律设计及试飞问题,通过杆位移-过载梯度的实时精确调整及取大值逻辑指令切换,设计了迎角保护控制律,实现拉杆到底飞机迎角达到且不超过限制迎角的目的。根据迎角保护控制律的功能及试飞目的,将整个试飞过程分为三个阶段,研究了各个阶段的试飞技术。仿真结果表明,所设计的控制律能够实现迎角保护功能,具有良好的控制效果。     

三维自适应终端滑模协同制导律

针对多枚导弹协同作战的问题,且多枚导弹之间保持有向拓扑通信的条件下,基于终端滑模法设计了视线方向及视线法向的双层协同制导律。其中,视线方向的制导指令能够保证导弹同时完成拦截任务;视线法向上的三维制导律能够保证每枚导弹以期望的视线角攻击目标,从而发挥各枚导弹的最大杀伤力,并且视线角的约束相当于规划了末制导段导弹的弹道问题,在一定程度上避免攻击目标前导弹间发生碰撞。同时,针对所设计的滑模制导律设计了新的自适应律,从而加快了滑模面的收敛速度并且削弱了由符号函数引起的系统抖振现象。基于李雅普诺夫稳定性理论,证明了所设计制导律的正确性,并在最后给出了数学仿真实验,验证了所设计制导律的有效性及优越性。     

纤维增强涡轮轴结构失效模式分析方法及试验验证

针对连续纤维增强复合材料涡轮轴结构失效模式分析问题,基于宏-细观力学跨尺度分析方法,建立细观力学代表性体积元(RVE)模型,通过编程模拟实现模型的周期性边界条件,计算纤维增强复合材料应力响应,将其均值应力转化为真实应力,确定失效包线。建立连续纤维增强轴结构力学模型,计算轴结构在扭转载荷下的应力响应。通过复合材料层合板主偏轴关系应力转化,将危险单元各方向宏观应力响应计算结果转化到细观力学RVE模型上,即为细观力学RVE模型受载情况。结合细观力学失效边界确定复合材料轴结构危险位置失效模式,当扭转载荷达到5 000～5 500 N·m之间,复合材料最外层即层6(+45°)首先达到基体拉伸失效载荷。开展复合材料轴结构失效模式试验,在扭转载荷达到6 000 N·m时,声发射信号相互叠加,大部分均为中频信号,中频信号多为基体、界面开裂信号。与模拟仿真计算结果对比分析,验证连续纤维增强复合材料涡轮轴结构失效模式分析方法的有效性。利用所建立模型预测了某型发动机低压涡轮轴的失效载荷及失效模式。     

TGO非均匀增长对热障涂层应力演化和破坏机理的影响

采用内聚力模型和热生长氧化层(TGO)非均匀增长子程序,数值模拟了在热循环载荷作用下热障涂层(TBC)内部应力演化规律和开裂行为。涂层失效过程首先是源自陶瓷层(TC)内近波峰位置的拉伸和切应力共同主导的陶瓷层Ⅰ、陶瓷层Ⅱ混合型裂纹;随着循环数增加,则转向由TC内近波峰位置的切应力主导的Ⅱ型裂纹和波峰波谷中间的涂层厚度方向拉伸应力主导的Ⅰ型裂纹。整体非均匀增长和波谷均匀增长模式下的最大拉伸应力经过一定循环数后几乎不再随循环数而增加;而在波峰均匀增长和整体均匀增长模式下,最大拉伸应力则会随着循环数增加持续增长。整体非均匀增长、波谷非均匀增长模式下,20个循环后最大切应力出现在近波峰位置,分别为-16241 MPa和-15428 MPa;而整体波峰均匀增长和整体均匀增长模式下,最大切应力为-11382 MPa和-11198 MPa。对于波谷均匀增长和整体非均匀增长模式,在9个循环后出现界面裂纹。而对于波峰均匀增长和整体非均匀增长模式,在第17个循环出现界面裂纹。     

Optimization and verification of free flight separation similarity law in high-speed wind tunnel

Based on the similarity of separation time, a similarity law optimization method for high-speed weapon delivery test is derived. The typical separation state under wind load is simulated by the numerical method. The real separation data of aircraft, separation data of previous test methods, separation data of ideal wind tunnel test of previous methods, and simulation data of the proposed optimization method are obtained. A comparison of the data shows that the method proposed can improve the performance of tracking. Similarity law optimization starts with the development of motion equations and dynamic equations in the windless state to address the problems of mismatching between vertical and horizontal displacement, and to address the problems of separation trajectory distortion caused by insufficient gravity acceleration of the scaling model of existing light model. The ejection velocity of the model is taken as a factor/vector, and is adjusted reasonably to compensate the linear displacement insufficiency caused by the insufficient vertical acceleration of the light model method, so as to ensure the matching of the vertical and horizontal displacement of the projectile, and to improve the consistency between the test results of high-speed projection and the actual separation trajectory. The optimized similarity law is applicable to many existing free-throwing modes of high-speed wind tunnels. The optimized similarity law is not affected by the ejection velocity and hanging mode of the projectile. The optimized similarity law is suitable not only for the launching of the buried ammunition compartment and external stores, but also for the test design of projectile launching and gravity separation.     

某型装备轴承件无失效时的可靠性参数估计

针对寿命服从威布尔分布的某型装备轴承件在无失效数据时的可靠性参数估计问题,首先,以失效概率为待估参数,取其先验分布为Beta分布,在2个超参数的先验密度函数为2种不同情形下,建立了失效概率的2种EBayes估计模型,分析了稳健性、渐近性和单调性;然后,对威布尔分布参数进行了加权最小二乘估计,进而建立了可靠度的2种E-Bayes估计模型,分析了稳健性和单调性;最后,结合实例数据进行了可靠性参数估计与分析,指出第2种估计模型更加合理有效。     

试飞试用阶段的飞机可靠性评估研究

飞机的可靠性水平是飞机设计定型时考核的重要指标之一,为保证评估结果的客观与准确性,在飞机 试飞试用阶段开展可靠性评估研究尤为重要。本文从工程实际需求出发,通过规范评估对象故障信息的采集 方式,明确故障判定准则与统计原则,给出完整的飞机可靠性评估流程;基于上述流程,针对某型飞机一年中的 试飞试用信息,进行多维度的可靠性评估。结果表明:评估结果能够较好地反映飞机的可靠性水平,满足工程 需要。