相位法曲面三维可测梯度极限的研究

简述了相位法曲面三维全场无接触检测的基本原理，研究了被测曲面的梯度变化对频谱分析和滤波处理的影响，推导出相位法曲面可测梯度极限的理论公式，并通过锥面测量验证了这一公式的正确性。     

模拟地球同步轨道辐照环境对光学太阳反射镜性能的影响

研究了模拟地球同步轨道辐照环境对卫星用温控涂层-光学太阳反射镜(OSR)性能的影响。对所研制的两类OSR 片进行的辐照试验项目有,真空紫外辐照、低能电子和两种能量的质子辐照。此外还进行了等离子体环境条件下的表面充/放电效应试验。经过相当于安装在地球同步轨道卫星南北极位置处,在空间七年所受到的电子、质子和紫外辐照总剂量的辐照后,导电型OSR 的太阳光谱吸收率α_s 由0.068增加到0.078,法向发射率ε_n 由0.83降低到0.72;而非导电型OSR的α_s 由0.066增加到0.085,ε_n 由0.82降低到0.76。表面充/放电试验的结果表明:导电型OSR 的充电电位仅在15～40V 之间,而非导电型OSR 的充电电位则可高达13kV。因此导电型OSR能有效地控制表面的充/放电现象。     

声光相关技术在电子战中的应用

介绍了声光相关技术原理及其在现代战争,特别是在电子战及扩频通信等方面的应用,比较了体波及其表面波、声光及声电技术在应用中的不同特点,并具体探讨了声光相关器应用子通信信号的解调及同步中的可行性,分析表明,声光相关技术是很有发展前景的一项技术,将越来越多地应用于各个不同的领域。     

微重力场中对流—辐射—传质系统的地面模拟技术

研究了微重力条件下对流－辐射－传质稳态系统的地面相似模拟技术，进一步发 温度－材料综合保护技术。通过采取补偿热流，调整壁面热流密度分布的方法，保持了原型与尺寸适当缩小后的模型的Ｎｕ数，Ｓｈ数，材料，温度，湿度不变，从而实现模型与原型流动，换热和传质相似。     

防静电白色热控涂层的空间环境性能试验

通过在氧化锌晶格中掺入重金属离子，得到具有防静电功能的白色颜料，再以丙烯酸树脂为粘合剂制备出空间飞行器外表面用的ACR－1防静电白色热控涂层；研究了空间环境效应（包括紫外辐照，电子和质子辐照）对该热控涂层太阳吸收率的影响并与有机硅白色热控涂层进行了比较，地面模拟空间环境试验研究结果证明，ACR－1防静电白色热控涂层具有良好的空间稳定性。     

微重力下管肋式空间辐射器的整体优化分析

建立了向一重力环境下管肋式空间辐射器传热过程的数学模型，并以单质量散热量最大和热载体驱动功率最小为优化目标，对管式空间辐射器进行了优化分析。     

实测载荷谱数据处理系统

简要介绍了实测载荷谱数据处理系统，较深入地论述了实测载荷谱数据处理的几个重要方面，给出了该系统处理直升机旋翼系统动部件实测载荷谱的实例，通过大子样二维疲劳２载荷母体分布参数估计及假设检验，发现载荷幅值服从半正态分布，载荷均值服从三参数Ｗｅｉｂｕｌｌ分布。     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

一种气动式冲击响应谱试验系统的设计与分析

大多数航天器单机产品都要求进行冲击响应谱试验,试验量级普遍为1000g~2000g,甚至超过3000g。对于较大质量(如50 kg以上)产品高量级的冲击试验,振动台、传统的摆锤式或跌落式冲击试验台均很难满足相关要求。文章研究并设计了一套能够进行大质量受试产品高量级冲击响应谱试验的气动冲击试验系统。该系统利用压缩空气瞬间释放膨胀推动质量块加速撞击具有多阶固有频率的谐振板,通过谐振板被激起的响应模拟复杂的衰减正弦波。测试结果表明,系统空载时冲击谱量级达8000g,负载200 kg时可达5000g,时域曲线为振荡衰减波,持续时间小于10 ms。文章提出的气动式冲击响应谱试验系统设计方法可为此类冲击试验系统的设计提供参考和理论依据。     

Numerical simulations of water spray on flame deflector during the four-engine rocket launching

This paper aims to study on the cooling effect with two types of water spray nozzle on the flame deflector during the four-engine launch vehicle take-off. To accurately simulate the two-phase flow of the rocket gas with multispecies and the water spray, the three-dimensional compressible Navier-Stokes equations, discrete ordinates methods and realizable k-Ɛ turbulence model are used to establish the rocket supersonic plumes impact model. The Eulerian dispersed phase (EDP) model was used to simulate the water spray into the exhaust gas. The accuracy and effectiveness of the gas-liquid flow model are verified by a good agreement between simulation results and experimental data. On this basis, a series of numerical simulation studies under different water injection position are performed. The results show that the high temperature regions, along the axis of engines on the deflector plate, have no significant temperature decreasing effect by water spray from the nozzles mounted on the apex of the deflector, and the high temperature converts a large quantity of water into vapor near the plume boundary, which would decrease the flow conductivity. With the cooling spray nozzle fixed directly to the deflector plate, the temperature decrease effect is obvious and the effect of thermal shock on deflector plate induced by exhaust plume is reduced, so that it can prevent the flame deflector from thermal ablation. The study results provide indepth information and engineering guidance for designing the water spray systems and increasing the safety of the launch process.