某型无人机拦阻网回收系统设计

介绍了无人机拦阻网回收系统的组成和工作原理，论述了系统的网体设计、涡轮阻尼器设计以及拦阻过程计算等关键技术问题，并给出某型无人机拦阻回收系统的性能计算结果。本文的研究成果为某型无人机拦阻网回收系统的工程设计提供了理论依据，并已成功应用于某型无人机系统的研制。     

Effect of protrusion amount on gas ingestion of radial rim seal

In this paper, the effect of different amount of protrusion on various parameters in rotor–stator system was experimentally studied by measuring CO₂ concentration and pressure, in order to obtain the optimal protrusion amount. The parameters of different dimensionless sealing flow were measured under the condition that the annulus Reynolds number was 4.39 × 10⁵ and the rotating Reynolds number was 1.05 × 10⁶. The results show that the change of the amount of protrusions has little effect on the static pressure in the cavity, and the static pressure change near the sealing ring is almost negligible. But the total pressure and sealing efficiency increase first and then decrease with the increase of the amount of protrusion. The variation of power consumption is the same. A complex vortex structure will appear at the high radius region when the protrusion is installed. On the other hand, the protrusion can effectively reduce the minimum sealing flow of the rotor–stator cavity. Furthermore, considering the sealing efficiency and power consumption, the best range of the protrusion amount is about 36. The ratio near this range can optimally balance the alleviation of the gas ingestion and the reduction of the power consumption.     

高主流湍流度下密度比对涡轮导叶全气膜冷却特性的影响

为了研究高主流湍流度下二次流密度比对涡轮导叶全气膜冷却特性的影响,使用热色液晶测量了在主流湍流度为15%,二次流密度比为1.0和1.5下三维涡轮导叶的气膜冷却效率和换热系数。二次流与主流质量流量比为7.0%和12.5%。结果表明:二次流密度比增大可以降低冷气射流的动量,小流量比工况下,在叶片前缘和压力面前半段,动量较低的二次流在高主流湍流度的影响下更易耗散,增大二次流密度比使冷却效率明显降低;大流量比工况下,二次流动量降低使气膜孔后区域冷气贴附性增强,气膜冷却效率和冷气覆盖效果均得到提升。小流量比工况下,二次流密度比增大对叶片表面换热的影响较小;大流量比工况下,二次流密度比增大使吸力面中弦区域和压力面后半段的平均换热系数比分别降低15%和25%。     

An equilibrium multi-objective optimum design for non-circular clearance hole of disk with discrete variables

An Equilibrium Multi-objective Optimization Model(EMOM) with self-regulated weighting factors has been proposed for the optimum design of non-circular clearance hole on the front flange of turbine disk. In the ‘‘equilibrium design", both the stress decrease around the hole and the least hole's profile variation are considered, which balances two ambivalent design goals. Specific discrete variables are applied to realize the standardization design in the optimization process, in which a Surrogate Genetic Coding Algorithm(SGCA) is introduced, and a special check module is used to get rid of repeated fitness evaluation of the samples. The method offers an equilibrium design for the non-circular clearance hole of the turbine disk with great accuracy and efficiency.     

Flow mechanism between purge flow and mainstream in different turbine rim seal configurations

The rim seal is used to prevent mainstream ingestion to the gap between the vane of a turbine and its blade. In this article, the dolphin lip with a hook configuration and a large seal cavity with hook structures are designed based on the high-pressure turbine datum single shark lip rim seal configuration. The sealing effect and parameters of the flow field are measured by an experiment method and a numerical simulation is used to explain the mechanism. For three configurations, the effect of the leakage slot vortex on the efficiency of the seal and the influence of leakage vortex, generated by the interaction between purge flow and mainstream flow, are discussed in depth. The result shows that the reverse vortex formed by the dolphin lip rim seal with hook structure will increase the sealing efficiency. The seal configuration with a large cavity improves sealing efficiency to a greater extent than the datum structure. At different purge flow rates and with unequal seal structures, the purge flow produces three types of leakage vortices in the passage. Besides, the seal configuration with dolphin lip produces a Kelvin-Helmholtz instability at the interface of the purge and the mainstream flows at a low purge flow rate to induce new leakage vortex branches in the passage of the blade.     

先进铝化物涂层制备技术进展

铝化物涂层是现役发动机热端部件高温氧化防护的主要手段。未来,高性能铝化物涂层仍是发展先进发动机所必需的技术。传统基于化学气相的制备方法不仅污染环境,腐蚀设备,效率低下,更重要的是难以有效制备高性能铝化物涂层。高效"绿色"化将是先进铝化物涂层制备技术的发展趋势。近年通过利用机械能辅助的策略获得了高效制备铝化物涂层的方法。另外,利用真空物理气相沉积加高温扩散的策略,"绿色"制备高性能铝化物涂层的研究也进展显著。结合上述两种策略,利用真空等离子辐照形成的离子撞击能,可高效、"绿色"地制备铝化物涂层,为高性能铝化物涂层的制备提供了一种新的有效途径。     

失调叶盘结构模态特性及抗共振可靠度分析

为了探究航空发动机失调叶盘结构的固有频率在不同随机参数下的分布规律,建立了叶盘结构的有限元模型,对各随机变量选取了不同的失调程度.利用拉丁超立方抽样与响应面相结合的方法,对不同结构参数、工况下的叶盘固有频率进行了概率分析,得到了其在不同失调情况下的分布特性以及对各输入参数的灵敏度.利用工程振动理论建立了结构共振失效的极限方程,给出了叶盘结构在随机频率的激振力下的抗共振可靠度的计算方法,并对不同材料属性参数失调程度下的叶盘抗共振可靠度进行了计算,得出了叶盘抗共振可靠度在不同程度的材料属性失调下的变化规律.     

旋翼桨叶结冰对直升机飞行性能的影响

采用由翼型冰风洞试验推导而来的工程公式,将旋翼结冰模型嵌入离散格式的旋翼气动模型,分别计算结冰后每个桨盘网格区域的翼型升、阻力系数的增量和挥舞系数的增量,建立了结冰后的UH-60A直升机飞行力学模型.结合发动机功率数据,通过改变结冰条件,研究了不同结冰参数对最大平飞速度、最大垂直爬升率和最大爬升率的影响.结果表明:在环境温度为0~-10℃时,降低环境温度会严重降低飞行性能;液态水含量对所选性能指标有一定影响;水滴直径对最大平飞速度的影响较小,对爬升性能的影响可忽略不计;飞行性能指标随结冰时间呈线性下降趋势.      

燃气轮机燃烧室预混喷嘴排放性能的试验和数值研究

为了研究当量比、值班燃料量和压力对燃气轮机燃烧室预混喷嘴排放指标的影响,在环境压力下按照等速模化原理进行了燃烧室预混喷嘴的燃烧试验,基于化学反应网络法构建了污染物预测模型,开展了试验和数值对比研究。结果表明:在带值班燃料的情况下该预混喷嘴当量比φ在0.35～0.5时可满足国标排放要求,但是值班燃料量增大会使NO_x排放升高;在φ0.4时,压力对纯预混燃烧NO_x生成无影响,φ0.4时,NO_x会随压力升高而增多;带有值班燃料的预混燃烧时,NO_x对压力变化敏感,压力升高导致NO_x增多;该预混喷嘴混合性能对空气流速不敏感、燃料兼容性强,排放达标当量比范围宽,经进一步设计开发后有潜力应用于燃气轮机低排放燃烧室中。该化学反应器网络模型依赖经验较少,当值班燃料比例≤0.17时,对污染物预测与试验数据符合较好。     

涡轮叶片尾缘凹坑/凸起结构气膜冷却特性研究

为探究吸力面凹坑和凸起结构对涡轮叶片尾缘气膜冷却特性的影响,在吹风比M=1.1时(雷诺数Re=2.5×10~5),采用数值模拟方法,通过在叶片尾缘吸力面上加入凹坑或凸起,对涡轮叶片尾缘的冷却性能和流动机理进行了详细分析。结果表明:与原始结构相比,叶片尾缘凹坑和凸起结构提高了劈缝出口下游远距离端X/H6 (H为劈缝宽度,为4.8mm)区域气膜冷却效率,对下游的X/H6区域气膜冷却效率影响较小;三种叶片尾缘结构,沿着流向方向会产生由二维展向涡到发卡涡,再到流向涡的变化过程,凹坑和凸起结构通过抑制流体的扰动,改变流体流动情况,提高了劈缝出口下游远距离端气膜冷却效率。