均匀各向同性大气湍流对声爆传播特性的影响

基于离散Fourier模态有限和生成的随机大气湍流场，采用修正波形参数方法，开展了均匀各向同性大气湍流对典型超声速客机声爆传播特性的影响分析。计算采用的超声速客机模型为自行生成的简化超声速公务机模型。首先，应用航空工业空气动力研究院自主研制的CFD软件ARI_Overset在三维空间求解Navier-Stokes方程，得到作为声爆远场传播初始值的近场空间压力分布；其次，基于Von Karman能量谱，采用离散Fourier模态有限和形式生成随机均匀各向同性大气湍流场；最后，采用修正波形参数方法模拟了声爆信号在随机速度湍流场中的传播过程。数值结果表明：各向同性大气湍流对于地面声爆特征有重要影响。与无湍流状态相比，均匀各向同性大气湍流使得地面声爆特征增强的概率约为55%，使得地面声爆特征减弱的概率约为45%，故总体而言大气湍流效应更倾向于增强地面声爆特征；均匀各向同性大气湍流对于声爆传播路径影响相对较小，但是这一变化仍会导致地面信号接收点的不确定性。     

低温磨料气射流加工PDMS实验研究

通过自研的低温磨料气射流加工装置进行低温磨料气射流加工聚二甲基硅氧烷(polydimethylsiloxane,PDMS)实验研究,分析了加工时间、加工距离、冲蚀角度和磨料粒径对冲蚀率、孔深和孔横截面形貌的影响。结果表明:随着加工时间的增加,冲蚀率先增大后减小,在第1阶段加工过程中,孔深与加工时间大致呈线性关系,增加加工时间还可使孔底部变平整;存在一个最佳加工距离使孔深最大,当加工距离大于最大加工距离时,孔深将随着加工距离的增加而急剧下降,孔的锥度随着加工距离的增大而增大;当冲蚀角度处于30°～60°之间时,冲蚀率最大,随着冲蚀角度的增加,孔的形状逐步由椭圆形变成圆形;存在一个最佳磨料粒径,使冲蚀率和孔深达到最大;当冲蚀角度小于90°时,低温磨料气射流加工PDMS材料去除机理为塑性去除和脆性去除的结合。     

多段翼混合边界层改变对流场的影响研究

前缘缝翼尾流与主翼边界层混合的改变对主翼气动力具有重要影响.利用数值模拟手段,通过在前缘缝翼尾缘添加一定动量系数的喷流,改变前缘缝翼尾缘的尾流,进而改变尾流与主翼边界层的混合状况.求解二维多段翼模型30P30N在各个不同喷流条件下的二维非定常流场,结果表明:提高前缘缝翼尾缘喷流的动量系数,将使前缘缝翼尾流和主翼边界层混合开始点后移,提高主翼上表面负压峰值和主翼升力;混合开始点对主翼的负压峰值及升力均有一定的影响;增大来流攻角会抑制前缘缝翼尾流和主翼边界层的混合.     

基于磁共振线宽的Xe核自旋横向弛豫时间测量方法

随着核磁共振陀螺技术的发展,高精度核磁共振陀螺对原子气室性能提出了更高要求.原子气室内Xe核自旋的横向弛豫时间(T2)是衡量原子气室性能的重要参数之一,T2的常用测量方法为自由感应衰减法(Free Induction Decay,FID).当T2较短时,由于自旋进动信号易受外界干扰,FID方法难以对T2进行精确测量.根据磁共振线宽理论以及自旋进动信号检测技术,针对T2较短的原子气室,提出了基于磁共振线宽的Xe核自旋横向弛豫时间测量方法,构建了测试装置,对Xe核自旋进行了测试.测试结果表明,该测量方法能够有效获得Xe核自旋的横向弛豫时间,克服了FID方法对T2较短的原子气室难以测量的局限性,为检验核磁共振陀螺中原子气室的性能提供了有效测试手段.     

火花放电合成射流与超声速来流相互干扰特性数值模拟研究

为了指导火花放电式合成射流激励器在超声速流动控制中的应用,数值模拟研究了火花放电合成射流与超声速来流的相互干扰特性。研究表明火花放电式合成射流在超声速流场中产生强烈扰动,产生较强的激波结构;随着射流的喷出,激励器上游分离区和流场中激波呈先增强后减弱的趋势,激波由弓形激波逐渐弱化为斜激波,并且随着放电能量的增加射流与主流的动量通量比不断增大,射流的干扰和控制能力显著增强。由于超声速流的较大惯性及其对腔内气体的引射作用,激励器的腔体回填速率大幅下降、回填时间明显增长,使得激励器的工作频率受到很大限制。     

Effects of synthetic jet frequency on the separated flow in a diffusing S-duct

Numerical simulations were carried out to investigate the effects of synthetic jet actuation frequency on the separated flow in a diffusing S-duct. The Reynolds number based on the entrance height was 9.78×105. At first, the numerical model was validated with experimental data, and then, the interaction between the separated flow and the synthetic jets at different frequencies was discussed. The results demonstrate that the control effect is significantly dependent on the momentum mixing enhancement between inside of the separated boundary layer and the outer flow. There exists a narrow range of actuation frequency, in which effective separation control can be achieved using synthetic jets. A dimensionless frequency F+=1.0 is identified as the optimal frequency, with a momentum coefficient of 1.62×10-3, the separation area is reduced about 46%, and the aerodynamic performance of the S-duct is also greatly improved compared to uncontrolled case. Further analysis reveals that the choice of actuation frequency is mainly determined by the momentum flux produced by a single ejection and the spacing between adjacent ejections, the optimal frequency case can be understood as a balance between the two factors. In addition, it is found that the synthetic jets can also suppress the secondary flows while decreasing the separation.      

多喷嘴构型的轴对称氢氧加热器设计与仿真

为了使氢氧燃烧加热器满足自由射流试验台工作需要并获得均匀的出口气流参数,采用同轴剪切式7个喷嘴轴对称构型喷注器,利用CFD仿真软件对其进行了三维反应流场计算,燃烧模型采用氢氧单步反应模型,获得了设计工况下的参数.计算结果表明:燃烧效率随着中心喷嘴与外围喷嘴距离L与喷注面板半径R之比(L/R)的增大先上升后下降;喷注面板的温度随着L/R的增大而降低,最终维持在600K左右;加热器出口的氧气摩尔分数以及总温的均匀性基本不随着L/R变化而变化;出口主流区的马赫数在6左右满足设计要求.在各个喷嘴的影响区域大致相等时,加热器综合性能良好.氢氧速度比越大,完全燃烧所需区域越短,喷注面板温度越高.与单喷嘴、19个喷嘴的加热器比较发现7个喷嘴的构型较为合理.      

煤基喷气燃料在地面单管燃烧室内燃烧和排放特性研究

为研究煤基喷气燃料的燃烧和排放特性,通过改造的单管燃烧室评估了煤基喷气燃料和石油基RP-3喷气燃料的燃烧和排放特性差异.试验结果表明:煤基喷气燃料具有更加优异的贫油点火和贫油熄火性能,两种喷气燃料的燃烧和排放特性随燃油流量和燃烧室出口温度的改变呈现出一致的变化趋势,在相同质量流量下,煤基喷气燃料的燃烧和排放性能要低于RP-3,在相同燃烧室出口温度时,煤基喷气燃料燃烧时的壁温要低于RP-3.      

煤基喷气燃料代用组分神经网络混合构建方法

为了建立航空燃料的喷雾模型,用于高保真液雾燃烧数值模拟,提出了基于人工神经网络混合模型的煤基喷气燃料代用组分构建方法.基于这一构建方法,重点针对煤基喷气燃料的雾化特性,利用多组分混合燃料的理化性质数据库对神经网络进行训练,获得了混合燃料理化性质隐式预测模型,结合随机投点优化方法,构建出能够很好地模拟煤基喷气燃料目标理化性质的代用组分.结果表明:该代用组分包含了5种碳氢化合物成分,摩尔分数为11.46%正癸烷、23.29%正十二烷、49.87%正十四烷、6.66%异辛烷和8.72%甲基环己烷.通过雾化特性实验,验证了代用组分对真实燃料雾化性能的模拟效果.该代用组分构建方法可以较好地解决混合燃料模拟过程中的非线性问题,通过改变目标理化性质可构建出相应代用组分.      

Design and implementation of rigid-flexible coupling for a half-flexible single jack nozzle

The aerodynamic design of a rigid-flexible coupling profile is the decisive factor for the flow-field quality of a supersonic free jet wind tunnel nozzle, and its mechanic dynamic features are the key for engineering implementation of continuous Mach number regulations. To fulfill the requirements of a free jet inlet/engine compatibility test within a wide simulation envelop, both uni-form flow-fields of continuous acceleration and deceleration are necessary. In this paper, the aero-dynamic design methods of an expansion wall and machinery implementation plan for the half-flexible single jack nozzle were researched. The profile control in nozzle flexible plate design was studied with a rigid-flexible coupling method. Design and calculations were performed with the help of numerical simulation. The technique of axial free stretching of the flexible plate was used to improve the matching performance between the designed elasticity profile and the theoretical one, and the rigid-flexible coupling structure was calibrated by wind tunnel tests. Results indicate that the flexible plate aerodynamic design method used here is effective and feasible. Via rigid-flexible coupling design, the flexible plate agrees with the rigid body very well, and continuous Mach number changes can be achieved during the tests. The nozzle’s exit flow-field uniformity meets the requirements of China Military Standard (GJB).