发动机双发失效空滑策略研究

双发失效是飞机在发动机试飞中可能遇到的最大风险。通过提前规划双发失效后的垂直、水平路径,让飞行机组在遇到双发失效特情时能按照预先规划的路径飞行,遵循最有利的能量使用,减轻机组在特情时的负荷和避免做出不良决策,以期降低双发失效风险带来的影响。     

当量比对连续旋转爆轰燃烧室特性的影响

为了探究当量比对甲烷-空气连续旋转爆轰燃烧室（CRDC）特性的影响,利用二维可压缩欧拉方程对CRDC进行了数值研究,分析了爆轰波的发展过程和贫燃熄火过程,对比了不同工况下CRDC特性参数的变化情况。结果表明:CRDC起爆后燃烧场在由不稳定状态到相对稳定状态的过程中发生了2次碰撞,当进气当量比较低时,CRDC未能完全发生2次碰撞过程就已经熄爆。随着进气当量比的降低,爆轰波传播速度、轴向平均速度、出口平均温度、出口平均总压均呈下降趋势;增压比随当量比降低而减小的根本原因在于旋转爆轰燃烧过程和等压燃烧过程的熵增差减小,使吉布斯自由能增量差减小。CRDC的燃料驻留时间处于亚毫秒量级,燃烧热效率保持在99%以上。      

旋转整流罩积冰过程中水膜流动和脱离的数值研究

为了更准确地模拟旋转整流罩积冰过程,在现有三维积冰与冰层表面薄水膜流动耦合模型基础上,基于功平衡分析的方法引入了旋转部件表面水膜脱离模型,并发展了相应的计算方法,给出了水膜脱离的判定依据:当气流曳力做的功和由于离心力使水膜增加的潜能之和大于黏附功时整流罩表面的水膜会发生脱离。对旋转整流罩积冰进行数值模拟,计算结果与实验结果吻合得较好,验证了该模型的合理性和计算方法的可行性。之后分析了转速和来流速度对整流罩表面水膜脱离和积冰的影响,结果表明:转速和来流速度越大,水膜发生脱离的比例越大。在研究范围内,转速为3000r/min和6000r/min时,因水膜脱离导致积冰总量分别减少13.4%和15.8%;来流速度为40、50m/s和60m/s时,因水膜脱离导致积冰总量分别减少为12.2%、13.4%、14.2%。      

Investigation on surface roughness,residual stress and fatigue property of milling in-situ TiB2/7050Al metal matrix composites

For higher efficiency and precision manufacturing, more and more attentions are focused on the surface roughness and residual stress of machined parts to obtain a good fatigue life. At present, the in-situ TiB₂/7050Al metal matrix composites are widely researched due to its attractive properties such as low density, good wear resistance and improved strength. It is of great significance to investigate the machined surface roughness, residual stress and fatigue life for higher efficiency and precision manufacturing of this new kind material. In this study, the surface roughness including two-dimensional and three-dimensional roughness, residual stress and fatigue life of milling in-situ TiB₂/7050Al metal matrix composites were analyzed. It was found from comparative investigation that the three-dimensional surface roughness would be more appropriate to represent the machined surface profile of milling particle reinforced metal matrix composites. The cutting temperature played a great role on the residual stress. However, the effect of increasing cutting force could slow down the transformation from compressive stress to tensile stress under 270 °C. An exponential relationship between three-dimensional roughness and fatigue life was established and the main fracture mechanism was brittle fracture with observation of obvious shellfish veins, river pattern veins and wave shaped veins in fracture surface.     

考虑随机干扰的高超声速滑翔飞行器轨迹优化

为解决高超声速滑翔式飞行器具有干扰不确定性的再入轨迹优化问题,提出了一种基于广义正交多项式方法的随机轨迹优化数值求解方法。针对随机干扰,基于广义正交多项式方式对其分布进行采样,形成采样空间,而后将每个采样值代入确定性轨迹优化问题中进行反复迭代求解,得出观测值的样本空间,并计算其期望、方差和协方差,估计输出值。以最大纵程为代价函数对具有随机干扰的高超声速滑翔式飞行器最优轨迹进行了数字仿真。仿真结果表明,基于广义正交多项式的随机轨迹优化方法能够有效处理随机干扰对轨迹优化问题的影响,与蒙特卡洛法相比计算效率大大提高。     

Spectroscopic data and Stark broadening of Cu I and Ag I spectral lines: Selection and analysis

Optical emission and linear laser absorption spectroscopy techniques were used in investigation of plasma with copper and silver admixture. The method of selection of spectral lines and spectroscopic data with the aim of diagnostics of multicomponent air plasma with two metal vapors admixture was developed. Energy level populations behavior on the Boltzmann plot were used for Cu I and Ag I spectroscopic data selection. In this way the selection of spectroscopic data for some of Cu I and Ag I lines was realized. Stark broadening parameters of Cu I and Ag I were examined. Experimentally obtained temperature and electron density radial distributions were used in the calculation of plasma composition in the assumption of local thermodynamic equilibrium. Linear laser absorption spectroscopy was used to examine the state of plasma.     

昆虫级褶皱翼型的滑翔气动特性

为了研究褶皱翼型上、下表面分别对气动力的影响,在弦长雷诺数为1200,攻角为0°~20°时,采用有限体积法研究了褶皱翼型、光滑翼型、上表面光滑的褶皱翼型和下表面光滑的褶皱翼型的滑翔气动特性.结果表明:在一定攻角范围内,褶皱翼型的升力系数较光滑翼型提高了10%;只要翼型下表面是褶皱的,产生的升力总大于下表面是光滑的,下表面褶皱对升力的提高具有更大作用;在大攻角下,光滑的上表面更有利于提高升力;在任何攻角时,上、下表面褶皱对阻力影响很小.      

凹腔前后缘圆弧对流场干扰的数值研究

基于两方程k-ωSST模型,对不同半径前后缘圆弧凹腔构型的超声速流场进行了二维仿真,获得了相应的流场特征参数。结果表明,与直角前后缘相比,采用圆弧构型时凹腔后壁的激波得到增强;随着圆弧半径的增加,凹腔内部的速度有所增大,而温度、涡量则呈递减趋势,从稳焰、助燃的角度看,后壁上端压力增大可以促进质量交换,同时降低回流区温度。综合考虑凹腔的稳焰和助燃作用,提出了一个适当的圆弧半径范围。     

低雷诺数下离心压气机性能及流动影响的数值研究

对高空低雷诺数条件下低压离心压气机进行了全三维数值模拟,分析了雷诺数对其内部流场的影响.结果表明:随着雷诺数降低,离心压气机的效率、裕度和流通能力下降;影响叶片表面负荷分布,使得转子叶片的做功能力下降;叶片前缘分离区范围增大,二次流增强,分流叶片叶尖泄漏损失增大,主叶片吸力面通道的低速区明显增大,起始位置也向前移动,对展向的影响区域也随之增加.      

双旋转盘腔压力特性实验

将压力传感器安装在测点测量几何结构复杂的双旋转盘腔转盘表面的压力分布及盘腔进出口的总压损失.实验结果表明:当湍流参数由0.1变化到0.4时,转盘表面的压力先随旋转雷诺数的增大而减小,之后随旋转雷诺数的增大而增大,并且转变的湍流参数对于两个转盘是不同的.在相同湍流参数下,旋转雷诺数决定了转盘表面的压力分布曲线形状;两个旋转腔的总压损失随湍流参数的增大而增大,随旋转雷诺数的变化规律不同,右旋转腔两个入口到出口的总压损失随旋转雷诺数的变化规律也有差异.