Collaborative manufacturing technologies of structure shape and surface integrity for complex thin-walled components of aero-engine: Status,challenge and tendency

Presently, the service performance of new-generation high-tech equipment is directly affected by the manufacturing quality of complex thin-walled components. A high-efficiency and quality manufacturing of these complex thin-walled components creates a bottleneck that needs to be solved urgently in machinery manufacturing. To address this problem, the collaborative manufacturing of structure shape and surface integrity has emerged as a new process that can shorten processing cycles, improve machining qualities, and reduce costs. This paper summarises the research status on the material removal mechanism, precision control of structure shape, machined surface integrity control and intelligent process control technology of complex thin-walled components. Numerous solutions and technical approaches are then put forward to solve the critical problems in the high-performance manufacturing of complex thin-wall components. The development status, challenge and tendency of collaborative manufacturing technologies in the high-efficiency and quality manufacturing of complex thin-wall components is also discussed.     

磨削表面形貌建模研究现状与展望

文 摘 磨削表面形貌是磨削表面完整性的重要指标之一,其对材料的接触应力、耐磨耐腐蚀性及抗疲劳强度等起着关键作用。本文概述分析了国内外在磨削表面形貌建模方法、技术路线、研究结果等所取得的进展,对磨削表面形貌建模的三类方法(经验建模法、理论建模法、有限元分析法)进行了综述,对各类建模方法的原理和优缺点进行论述,指出当前相关磨削表面形貌研究方向存在的问题。最后,提出了磨削表面形貌建模研究的发展方向。     

GGTm-Ts: A global grid model of weighted mean temperature (Tm) based on surface temperature (Ts) with two modes

With the development of Global Navigation Satellite System (GNSS), the detection of precipitable water vapor (PWV) using the GNSS atmospheric sounding technique becomes a research interest in GNSS meteorology. In the conversion of zenith tropospheric delay (ZTD) to PWV, the weighted mean temperature (Tm) plays a crucial role. Generally, the Tm estimated by the linear regression models based on surface temperature (Ts) cannot meet the requirement for global use, and the accuracy of Tm derived from the empirical models is limited. In this study, a new Tm model, named GGTm-Ts model, was developed using the global geodetic observing system (GGOS) atmosphere Tm data and European Centre for Medium-Range Weather Forecasts (ECMWF) data from 2011 to 2015. Resting upon a global 2.5°*2° grid of coefficients of Tm-Ts linear function, the new model can provide Tm at any site in two modes, one for the case with measured Ts provided, i.e., the accurate mode, the other for the case that Ts provided by a subroutine, i.e., the normal mode. The performance of GGTm-Ts model was assessed against the Bevis formula, GPT2w and GPT2wh model using different data sources in 2016-the GGOS atmosphere and radiosonde data. The results show that the GGTm-Ts model in accurate mode achieves best performance with an improvement of 46.9 %/15.3 %, 37.8 %/19.5 % and 34.4 %/14.2 % over other three models in the GGOS atmosphere/radiosonde comparison. For the normal mode, the GGTm-Ts model outperforms the GPT2w model and achieves equivalence results with the GPT2wh model. Moreover, the impact of Tm on GNSS-PWV was analyzed to validate the performance of the GGTm-Ts model.     

ELID沟道成形磨削氧化膜特性及影响作用实验

针对ELID沟道成形磨削特点,研究了磨削过程中氧化膜的特性及其影响作用。探讨分析了氧化膜的电流表征、氧化膜在沟道成形磨削中的状态变化以及氧化膜状态对磨削力和表面粗糙度的影响。实验过程中,电解电流从1 A增长到4 A,氧化膜厚度从35.33!m减小到11.07!m,法向磨削力从7.06 N增长到36.12 N,切向磨削力从1.62 N增长到4.47 N;垂直于磨削方向的表面粗糙度由0.256!m增长到0.355!m,平行于磨削方向的表面粗糙度由8 nm增长到13 nm。结果表明,氧化膜越厚,磨削力和表面粗糙度越小;氧化膜越薄,磨削力和表面粗糙度越大。     

TC4钛合金高速外圆磨削表面完整性实验

为充分发挥钛合金的优良性能,以TC4为研究对象进行高速外圆磨削实验,分析外圆磨削工艺参数对工件表面完整性的影响规律。结果表明:工件亚表面未出现变质层;随着砂轮线速度提高,表面质量提高;随着工件转速提高,表面划痕明显;随着磨削深度增加,出现表面烧伤现象,并且磨削深度对表面完整性的影响程度最大;磨削力与磨削温度对表面硬度的影响是正相关的,且磨削力对表面硬度的影响程度较大。因此可以通过选择合理的工艺参数来保证较大的材料去除率与较好的工件表面质量,为TC4钛合金高速外圆磨削提供指导。     

DD9镍基单晶高温合金磨削表面质量实验研究

涡轮叶片榫齿常采用磨削加工，磨削工艺参数决定了其加工表面的质量和疲劳性能。基于正交试验研究磨削参数对第三代镍基单晶高温合金DD9 磨削表面粗糙度及硬度的影响规律和机理。结果表明：磨削表面粗糙度受砂轮线速度vs 的影响最大，工件进给速度vw 对其的影响次之，而受磨削深度ap 的影响最小；磨削表面出现加工硬化，加工硬化程度在1.9%~13.8% 之间，亚表面硬化层深度在60~120 μm 之间；为获得粗糙度小、纹理均匀、硬化程度小的DD9 高温合金磨削表面，精加工推荐的磨削参数为vs∈［20 m/s，25 m/s］，vw∈［12 m/min，16 m/mim］，ap∈［10 μm，15 μm］。     

空间级硅橡胶胶黏剂粘结界面改性分析

针对空间级硅橡胶与聚酰亚胺的粘结界面呈现低表面能、粘结可靠性差的现状，利用有机硅烷的润湿和键结作用对界面进行预处理，改善其粘结强度。通过FTIR、¹H-NMR和GC-MS分析，有机硅烷的主要成分中对粘结性能影响较大的是正硅酸丁酯和丙基三甲基硅氧烷，采用两种偶联剂对聚合物表面进行预处理，在聚合物间不同均相结构层通过硅烷相互扩散和互穿网络形成的分子桥可实现致密交联。力学试验表明，经有机硅烷对待粘结界面表面预处理，粘结构件的剪切强度值可达0.65 MPa；选择适当的有机硅烷作为附着力促进剂，利用其有机官能团、成膜性和交联性可提高粘结构件的可靠性。     

CFRP夹层结构超声特征成像检测

采用便携式超声特征成像检测系统全波列采集检测信号,通过对缺陷特征信号的提取和重构,实现自动识别,可适用于曲面等不规则面的检测,定量精度达到0.1 mm。实验结果表明低频窄带超声换能器能够减小铜网对声波的衰减和畸变,超声特征成像层析成像方法可以对表面铜网结构CFRP泡沫夹层中分层、冲击和脱粘缺陷进行识别并精确定位和定量。检测方法快捷准确、重复性好、可靠性高。     

Effects of surface topography and specimen thickness on high-speed raindrop impact damage of CFRP laminates

Raindrop impact erosion has been observed since early days of aviation, and can be catastrophic for exposed materials during supersonic flight. A single impact waterjet apparatus is established for mimicking drop impacts at the velocities between 350 m/s and 620 m/s. Carbon Fiber Reinforced Polymer(CFRP) laminates with three different surface morphologies and specimen thicknesses are tested here. A central region with no visible damage has been noticed, surrounded by a “failure ring” with common...     

芳纶纤维表面改性及在EPDM 中的分散性

分别采用超声波法和物理机械法对芳纶纤维进行表面改性,研究了两种处理方法对其表面形貌、

分散性以及EPDM 复合材料性能的影响。结果表明:超声法和机械法使芳纶纤维表面形成差别较大的形貌特

征;其中芳纶经机械处理后呈现良好的分散性,其复合材料的拉伸强度和烧蚀深度分别为11. 3 MPa 和1. 2 mm

(10 phr),优于超声波法处理的结果。