基于复合疲劳试验的涡轮叶片振动应力反推法

提出了一种利用复合疲劳试验和外场故障数据反推涡轮叶片实际振动应力的方法.该方法针对与故障叶片同批次的叶片,开展数个振动应力水平下的单件试验和某一特定振动应力水平下的成组试验,利用极大似然法推导出叶片的概率-应力-寿命曲线(P-S-N);最后基于99.87%存活率下的概率-应力-寿命曲(P_99.87%-S-N),结合叶片的外场故障统计结果,反推出叶片实际工作中振动应力的范围和可能的最大振动应力.      

DZ125定向凝固高温合金长期时效后的显微组织和超高周疲劳行为

 选用950 ℃时效温度,对DZ125定向凝固高温合金进行了500、1 000、1 500 h的长期时效。利用超声疲劳试验机测试了合金的超高周疲劳性能。采用扫描电子显微镜、透射电子显微镜和电子背散射衍射(EBSD)研究了合金的显微组织和超高周疲劳行为。结果表明:长期时效对DZ125合金的组织稍有影响,长期时效后合金的点阵错配度降低,随着时效时间的延长,γ'相聚集长大更加明显,未出现拓扑密排相(TCP)等有害相;长期时效对DZ125合金的超高周疲劳性能稍有影响,随着时效时间的延长,疲劳性能呈下降趋势,疲劳断口较平整,裂纹起源于试样的表面,在超高周疲劳后合金的晶粒发生了小幅度旋转。     

组合压气机中导流叶片的尾迹抖动特性

为明确多排叶栅压气机中影响静叶尾迹抖动特性的因素及机理,探索调制静叶尾迹抖动周期和幅值的方法,采用数值方法对设计流量为1.12kg/s,转速为60000r/min的一级轴流和离心叶轮组成的组合压气机的非定常流场进行模拟.结果表明:静叶尾迹抖动除受几何因素影响外,还受上下游转子干涉影响,且上下游转子叶片通过频率的异同将影响静叶尾迹抖动的周期性.当上下游转子叶片同频通过时,改变动叶的时序位置可以调制静叶尾迹抖动幅值的大小.另外,静叶尾迹抖动幅值沿叶高方向并不相同,低叶高处静叶尾迹抖动幅值明显大于中、高叶高处静叶尾迹抖动幅值.      

膨胀循环发动机推力室传热优化

针对膨胀循环发动机推力室身部燃气侧的内壁增强换热结构和冷却剂侧的冷却通道结构这两个影响推力室身部换热最关键的结构分别进行多种结构下的数值模拟对比。通过分析各结构的模拟结果,得到了能够合理提高推力室身部换热能力的内壁加肋结构和圆柱段冷却通道深宽比的结构特征。     

依托ERP实现固定资产全寿命周期管理

固定资产是企业的重要劳动资料,是实现资产保值增值的重要工具。现有的固定资产管理模式已经无法应对当前电网企业对固定资产管理新形势的要求。资产全寿命周期管理是以资产的整体目标出发,统筹考虑资产的整个生命周期,在满足安全、效能的前提下追求资产全寿命周期成本最优的管理模式。本文提出通过运用ERP系统在固定资产生命周期内构建出一套完整的固定资产管理新模式,并通过在某地市级供电公司的实际运用,得出了运用此种新模式可以实现固定资产使用效率提高、全寿命周期成本降低的管理新要求。     

Designing method of acceleration and deceleration control schedule for variable cycle engine

Studies show that different geometries of a Variable Cycle Engine (VCE) can be adjusted during the transient stage of the engine operation to improve the engine performance. However, this improvement increases the complexity of the acceleration and deceleration control schedule. In order to resolve this problem, the Transient-state Reverse Method (TRM) is established in the present study based on the Steady-state Reverse Method (SRM) and the Virtual Power Extraction Method (VPEM). The state factors in the component-based engine performance models are replaced by variable geometry parameters to establish the TRM for a double bypass VCE. Obtained results are compared with the conventional component-based model from different aspects, including the accuracy and the convergence rate. The TRM is then employed to optimize the control schedule of a VCE. Obtained results show that the accuracy and the convergence rate of the proposed method are consistent with that of the conventional model. On the other hand, it is found that the new-model-optimized control schedules reduce the acceleration and deceleration time by 45% and 54%, respectively. Meanwhile, the surge margin of compressors, fuel–air ratio and the turbine inlet temperature maintained are within the acceptable criteria. It is concluded that the proposed TRM is a powerful method to design the acceleration and deceleration control schedule of the VCE.     

卫星产品声振组合试验技术研究

文章开展了声振组合试验技术的初步研究,探讨了卫星产品声振组合试验的控制方法,并以面积质量比大的卫星舱板产品为例研究了噪声与随机振动组合试验条件确定方法。结果表明:在进行噪声与正弦振动组合试验时,应先启动振动试验控制,后启动噪声试验控制,且正弦振动控制应采用滤波处理;在进行噪声与随机振动组合试验时,噪声激励与随机振动激励正常启动后,相互之间影响很小,可以按照要求的条件施加激励;对于面积质量比大的卫星产品,在结构上同时施加随机振动载荷和噪声载荷,声振组合试验考核更加合理。     

Integration of high-fidelity model of forward variable area bypass injector into zero-dimensional variable cycle engine model

Forward Variable Area Bypass Injector (FVABI) is one of key components which contributes to modulate the cycle parameters of Variable Cycle Engine (VCE) under various operation conditions. The modeling method of zero-dimensional FVABI was reviewed and its deficiency was analyzed based on FVABI flow characteristic. In order to improve the accuracy of VCE performance simulation, the high-fidelity modeling method of FVABI was developed based on its working characteristics. Then it was coupled with the zero-dimensional VCE model and the multi-level VCE model was built. The results indicate that the geometric and aerodynamic parameters can affect the interaction between the two airflows and the zero-dimensional FVABI model is too simple to predict the component performance accurately, especially when the FVABI inner bypass is chocked. Based on the performance curves for single bypass mode and the regression model of multi-scale support vector regression for double bypass mode, the high-fidelity model can predict FVABI performance accurately and rapidly. The integration of high-fidelity FVABI model into zero-dimensional VCE model can be done by adjusting iterative variables and balance equations. The multi-level model has good convergence and it can predict VCE performance when the FVABI inner bypass is chocked.     

火箭引射模态下主火箭总压与RBCC发动机的匹配性

基于传统的"等压面假设"理论,建立了RBCC发动机主火箭的引射性能分析模型,研究了主火箭总压与RBCC发动机的匹配性。研究结果表明,若隔离段通道面积比小于0.65,在主火箭总压较低条件下,隔离段内二次流容易达到壅塞,无法进一步提高空气流量;在地面静止状态下,随主火箭总压增加,空气流量逐步增大,等压面上形成Fabri壅塞后,进一步增加主火箭总压,反而会降低空气流量;在火箭引射模态下,RBCC发动机的工作状态可细分为引射作用占主导地位的进气道亚临界状态和临界状态、冲压作用占主导地位的进气道超临界状态,其分界马赫数分别约为0.7和1.5。     

某膨胀循环发动机推力室冷却结构流场仿真分析

为了研究某膨胀循环氢氧发动机推力室冷却结构流场分布特性,进行了单根冷却通道和完整冷却通道结构的三维CFD分析。仿真计算过程中,以单根通道模型的仿真结果作为完整通道结构模型流场仿真分析的边界条件之一,并考虑了材料物性参数随温度或压力的变化。分析结果表明:1)仿真预测的温升、压降与热试验实测值吻合,该推力室冷却通道流量相对偏差范围为-4.8%~6.6%,由此造成喉部气壁温的环向偏差为33 K;2)集合器管内流体的环向流动压差、法兰起分流或汇聚作用时拐弯效应形成的压力波动是造成冷却通道流量不均匀分布的主要原因,出口集合器内的压力分布对通道流量分布起主要作用;3)提高通道流量均匀性的措施可以从增大出口集合器管径或采用变管径设计、采用扩口型法兰并设置弧形导流片、集合器的进、出口法兰布置在同一环向位置等方面进行考虑。