封严篦齿腔内流动及旋涡分布和顶板换热特性的实验研究

自行设计了吸气式篦齿换热风洞并对篦齿腔内部旋涡分布及流场和篦齿顶板换热特性进行了详细的研究。测出了在不同雷诺数和齿隙比篦齿腔中旋涡分布和顶板换热规律。从机理上分析了雷诺数和齿隙比对篦齿腔内流动旋涡分布及顶板表面局部换热规律的影响。     

Solar modulation model with reentrant particles

We developed a one dimensional model of particle transport in the heliosphere. As opposite to widely used models, we apply a method where a quasi-particle is traced back in time. The model gives us the possibility to work on the possible existence of reentrant particles in the heliosphere that can be hardly solved by the traditional forward tracking method. Particles escape from the heliosphere and may reenter back. We estimate how these particles affect the modulation process in the heliosphere. Presented here are the results for different values of particles mean free path in the interstellar space and for different interstellar magnetic field values.     

Hale引理证明的修正

本文指出了著名的Ｈａｌｅ引理证明中的不足之处，并给以完善。     

大型水陆两栖飞机侧风起降的滑流影响分析

大型水陆两栖飞机AG600的动力装置为安装在机翼上的4台同向旋转涡轮螺旋桨发动机，针对1：15缩比模型带动力风洞试验显示的螺旋桨滑流对侧风起降状态的偏航力矩不稳定影响，对全机带动力风洞试验模型进行了大规模并行非定常数值计算，再现了风洞试验现象，通过流动机理分析明确其产生原因主要是左侧滑时右外翼分离和垂尾背鳍涡破裂，这些原因和数值模拟的准确性也为后期的风洞试验所证实。考虑到模型风洞试验中尺度限制造成的低雷诺数和高螺旋桨转速，为保证飞行安全，继续采用该非定常方法对全尺寸飞机真实侧风起降状态进行了详细数值分析和偏航稳定性评估。研究结果显示，在飞行雷诺数和螺旋桨转速下，相同侧风范围内风洞试验显示的流动不稳定因素基本消失，偏航稳定性允许的侧风范围明显增加。本研究实现了四发螺旋桨飞机起降状态横向气动特性的滑流影响非定常数值分析，建立了基于计算流体力学的风洞与飞行雷诺数效应的相互关系，进行了偏航稳定性的虚拟试飞评估，研究成果也为AG600飞机的首飞和飞行试验所验证。     

广义行列式及其应用

定义了一种广义行列式 ,并由此给出Gramer法则的一种推广     

航天器相对运动建模及周期性相对运动求解

面向航天器编队飞行的需求,对椭圆参考轨道航天器非线性周期相对运动条件进行研究,提出了确定椭圆参考轨道编队航天器非线性周期性相对运动条件的新方法。首先,考虑非线性、椭圆轨道等因素,通过哈密尔顿-雅可比(HJ)方程和正则摄动理论,推导了在任意非线性摄动下相对运动的模型和获得不需消耗任何燃料的周期性相对运动轨道的条件;然后,采用时域配点法,结合改进的列文伯格-马夸尔特(LM)法对周期性相对运动的初值进行求解;最后,设计数值仿真算例,利用上述条件,得到不消耗任何燃料的周期性绕飞轨道,由此验证了本文所提模型和方法的正确性。     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

风扇进口噪声预测模型的改进

针对Heidmann模型对风扇进口低频噪声(1k Hz)预测结果偏低的情况,通过引入风扇叶尖弦长雷诺数和相关几何参数改进了Heidmann模型中风扇进口宽频噪声的频谱修正函数,确定了其中频谱修正系数为0.085。对比改进模型和Heidmann模型的风扇进口噪声预测结果发现:在亚声速工况下,改进的模型很好地改善了风扇进口低频噪声的预测结果,改进幅值可以达到约45d B;而在超声速工况下,由于风扇进口产生的组合单音噪声成为风扇进口噪声的主要组成部分,除了在小于100Hz的频域内,改进的模型与Heidmann模型的预测结果差别不大。     

基于全局Newton-Raphaon方法的弹流润滑分析

基于全局Newton-Raphaon方法对滑动轴承的弹流润滑性能进行了数值摸拟。比较了弹性变形对连杆大头轴承最小油膜厚度和最大油膜压力的影响。结果表明:全局Newton-Raphaon方法很好的解决了收敛困难,程序运行时间长的问题;考虑表面弹性变形的连杆大头轴承与刚性轴承相比,最小油膜厚度与最大油膜压力的变化趋势相同;一个工作循环内,弹性轴承的最小油膜厚度略大于刚性轴承,而最大油膜压力则明显减小。     

连续尺度变换方程在稳态及非稳态流动模拟中的应用

为了提高涡粘性假设的湍流模型对于非稳态流动的求解精度,同时兼顾其对于稳态流动的求解性能,将雷诺应力项与连续变换方程(CSSE)结合而形成新的应力项,使其根据流场尺度、网格尺度及Kolmogorov尺度来自动调节当地的应力雷诺应力模化水平,避免网格因素在流场模拟中产生不利影响,改正了混合RANS/LES方法的速度型偏离对数率问题;同时,该方法并未引入显式亚格子模型(SGS),因此回避了亚格子系数确定对于流场模拟精度产生的影响,改善了湍流模型对于流动不稳定性的辨识精度。在湍流平板算例中,CSSE方法计算的边界层速度型精度与雷诺平均方法(RANS)相当,而对于圆柱尾迹的模拟则证明了CSSE方法具有混合RANS/LES方法的优点,即能够准确模拟流动的不稳定性特征。