异型孔空心叶片壁厚检测的试验研究

发动机叶片的结构型式和制造误差，直接影响发动机的性能和使用寿命。运用超声波法和电涡流法，对两种不同材料和形式的试件进行了试验。电涡流法受到探头直径和试件几何尺寸的影响，测量误差大，超声波法由于存在测量盲区，测量厚度的下限受到限制。但测量值与实际值相关，若对探头加以改进，用于异型孔空心叶片壁厚检测是可行的。     

Spectra and time variability of black-hole binaries in the low/hard state

We propose a jet model for the low/hard state of galactic black-hole X-ray sources which explains the energy spectra from radio to X-rays and a number of timing properties in the X-ray domain such as the time lag spectra, the hardening of the power density spectra and the narrowing of the autocorrelation function with increasing photon energy. The model assumes that (i) there is a magnetic field along the axis of the jet, (ii) the electron density in the jet drops inversely proportional to distance, (iii) the jet is “hotter” near its center than at its periphery, and (iv) the electrons in the jet follow a power-law distribution function. We have performed Monte Carlo simulations of Compton upscattering of soft photons from the accretion disk and have found power-law high-energy spectra with photon-number index in the range 1.5–2 and cutoff at a few hundred keV, power-law time lags versus Fourier frequency with index 0.8, and an increase of the rms amplitude of variability and a narrowing of the autocorrelation function with increasing photon energy as they have been observed in Cygnus X-1. The spectrum at long wavelengths (radio, infrared, optical) is modeled to come from synchrotron radiation of the energetic electrons in the jet. We find flat to inverted radio spectra that extend from the radio up to about the optical band. For magnetic field strengths of the order 10⁵–10⁶ G at the base of the jet, the calculated spectra agree well in slope and flux with the observations.     

盖板式预旋系统的压比和熵增特性

对预旋系统内的压力变化相关研究较少。基于理论分析、实验测量以及数值计算,对某盖板式预旋系统的压比及熵增特性进行研究。通过理论推导,对预旋系统内压比与无量纲温降的关系进行分析。在最高转速可达10000r/min的高转速实验台上,测量了转盘上的气流静压以及相对总温,进而获得压比及熵增特性。进行三维数值计算,将数值计算结果与实验结果进行了对比,并根据数值计算结果对预旋系统内的熵产分布以及各元件的熵增情况进行分析。结果表明:系统温降以及旋转马赫数大小决定了预旋系统的理想最大压比,而实际压比与理想压比的比值取决于系统内的熵增大小。采用数值计算以及实验测量所得结果对理论关系式进行了验证,最大偏差2.7%。旋转马赫数一定的条件下,随系统无量纲温降增大,系统压比逐渐减小。由于熵增影响,实测压比与理想压比最大相差约36%。预旋系统内的熵增主要发生在预旋腔静止壁面、接受孔前后、供给孔进口等气流旋转比发生剧烈变化的区域。预旋系统内主要元件的熵增随流量增大都呈逐渐增大的趋势,但接受孔处熵增最小值出现在喷嘴出口旋转比等于1左右时,流量过小或过大都会导致接受孔处熵增变大。     

飞机数字化装配系统中机身交点孔加工方法研究

针对传统交点孔加工方法加工精度低且存在回弹变形的问题,设计了一种满足飞机大部件数字化装配要求的机身交点孔精加工方法,根据交点孔的加工特性完成了机身定位与固持、数控加工中心定位以及加工工艺的总体设计,确定了交点孔加工程序原点的计算方法和编程原则,最后通过交点孔试切加工试验验证了加工方法的可行性。     

预旋系统稳态和非稳态计算对比研究

针对预旋系统由于旋转引起流场和温度场参数周期性瞬态变化的问题，分别采用滑移网格的瞬态法和固定转子相位的稳态法进行数值求解，并在稳态计算中通过改变转子相位来近似模拟非稳态问题的时空变化特性。通过稳态空间平均结果与非稳态时均结果的对比，以期为预旋系统非稳态问题的低成本求解提供方法依据。结果表明：稳态计算结果与非稳态计算结果相比，周期性波动频率一致，接受孔进口处，稳态计算的压力波动幅度小39%左右，温度波动幅度小15%左右；多个相位的稳态空间平均结果与非稳态时均结果相比，压力高0.2%，温度低0.1%；采用多个计算周期数与单个周期的非稳态计算结果差异微小。当采用喷嘴出口气流中心正对接受孔迎风面前缘的转子相位时，稳态计算结果与非稳态计算时均结果最接近。     

An equilibrium multi-objective optimum design for non-circular clearance hole of disk with discrete variables

An Equilibrium Multi-objective Optimization Model(EMOM) with self-regulated weighting factors has been proposed for the optimum design of non-circular clearance hole on the front flange of turbine disk. In the ‘‘equilibrium design", both the stress decrease around the hole and the least hole's profile variation are considered, which balances two ambivalent design goals. Specific discrete variables are applied to realize the standardization design in the optimization process, in which a Surrogate Genetic Coding Algorithm(SGCA) is introduced, and a special check module is used to get rid of repeated fitness evaluation of the samples. The method offers an equilibrium design for the non-circular clearance hole of the turbine disk with great accuracy and efficiency.     

Effect of tube-electrode inner diameter on electrochemical discharge machining of nickel-based superalloy

Nickel-based superalloys are widely employed in modern aircraft engines because of their excellent material characteristics, particularly in the fabrication of film cooling holes. How-ever, the high machining requirement of a large number of film cooling holes can be extremely chal-lenging. The hybrid machining technique of tube electrode high-speed electrochemical discharge drilling (TEHECDD) has been considered as a promising method for the production of film cooling holes. Compared with any single machining process, this hybrid technique requires the removal of more complex machining by-products, including debris produced in the electrical discharge machin-ing process and hydroxide and bubbles generated in the electrochemical machining process. These by-products significantly affect the machining efficiency and surface quality of the machined prod-ucts. In this study, tube electrodes in different inner diameters are designed and fabricated, and the effects of inner diameter on the machining efficiency and surface quality of TEHECDD are inves-tigated. The results show that larger inner diameters could effectively improve the flushing condi-tion and facilitate the removal of machining by-products. Therefore, higher material removal efficiency, surface quality, and electrode wear rate could be achieved by increasing the inner diam-eter of the tube electrode.     

微小孔特种加工技术研究现状及展望

近年来微小孔结构在航空航天零部件上的应用越来越广泛,对微小孔的特种加工方法的进展情况进行了综述,总结了每种加工方法的主要特点,并对当前微小孔特种加工技术存在的问题及未来发展趋势进行了总结和展望.     

Machining of a film-cooling hole in a single-crystal superalloy by high-speed electrochemical discharge drilling

Single-crystal superalloys are typical advanced materials used for manufacturing aeroengine turbine blades. Their unique characteristics of high hardness and strength make them exceedingly difficult to machine. However, a key structure of a turbine blade, the film-cooling hole,needs to be machined in a single-crystal superalloy; such machining is challenging, especially considering the increasing levels of machining efficiency and quality demanded by the aeroengine industry. Tube electrode high-speed electrochemical discharge drilling(TSECDD), a hybrid technique of high-speed electrical discharge drilling and electrochemical machining, provides high machining efficiency and accuracy, as well as eliminating the recast layer. In this study, TSECDD is used to machine a film-cooling hole in a nickel-based single-crystal superalloy(DD6). The Taguchi methods of experiment are used to optimise the machining parameters. Experimental results show that TSECDD can effectively drill the film-cooling hole; the optimum parameters that give the best performance are as follows: pulse duration: 12 ls, pulse interval: 30 ls, peak current:6 A, and salt solution conductivity: 3 m S/cm. Finally, a hole is machined by TSECDD, and the results are compared with those obtained by electrical discharge machining. TSECDD is found to be promising for improving the surface quality and eliminating the recast layer.     

接受孔形状对预旋供气系统内气流流动影响研究

为对比不同形状接受孔的预旋系统内气流流动特性,通过数值模拟方法,对带有不同形状接受孔的预旋系统进行了研究。研究发现:收缩型接受孔入口截面气流流通面积较大,相对速度较小,在预旋系统中的性能最优,其次是类梯型,最后是直孔型。同一旋转雷诺数下,带收缩型接受孔的预旋系统无量纲温降较直孔型提高5.8%,总压损失系数降低3.0%。三种类型接受孔的预旋系统无量纲温降和总压损失系数均随进出口压比的增加而增大,在相同压比下,收缩型接受孔预旋系统无量纲温降最大,总压损失系数最小。