模拟打伤/抛修缺口对TC17钛合金叶片振动疲劳性能的影响

研究了无缺口、打伤缺口和3种抛修缺口对TC17钛合金叶片振动疲劳性能的影响。结果表明,无缺口模拟叶片的疲劳寿命最长且寿命分散性最小,打伤缺口模拟叶片的疲劳寿命最短且寿命分散性最大,3种抛修缺口模拟叶片的疲劳寿命介于前两者之间,其中抛修缺口Ⅰ模拟叶片的疲劳寿命最长。无缺口和抛修缺口模拟叶片的疲劳裂纹均起源于叶片根部,打伤缺口模拟叶片的裂纹产生于缺口底部,与有限元模拟计算的最大应力位置吻合。模拟叶片的疲劳断裂区比较平坦,呈半椭圆形貌,疲劳源区主要位于模拟叶片表面的微小损伤处,疲劳扩展区具有典型的疲劳弧线特征,并呈现沿α/β片状组织界面开裂的特征。     

TA12钛合金加力筒体局部异常变色失效分析

针对某航空发动机在试车过程中多次出现加力筒体尾端局部区域异常变色现象,为了分析其故障原因,利用外观检查、材质分析和温色模拟试验等失效分析方法,确定了故障加力筒体变色部位经历了最高850℃左右的超温。为进一步评价故障加力筒体的可靠性,对其基体材料力学性能及组织演变规律开展研究。在TA12钛合金板材空冷状态下,从加热温度与组织及力学性能的关系分析结果表明:其力学性能随加热温度的升高呈先降低再提高的趋势,在800℃左右达到最低值,且力学性能变化趋势与组织形态演变呈明显的对应关系。根据加力筒体故障部位力学性能及可靠性明显降低的试验结果,判断该加力筒体不再适合继续参与服役试车,建议更换该故障件,并对替换件进行监控。     

薄壁大尺寸铌钨合金喷管精密旋压成形工艺研究

通过对铌钨合金性能的研究,得到了铌钨合金一次旋压最大减薄率,采用变厚度平板旋压毛坯,合理分布两次剪切旋压变形量和各点壁厚变薄率,控制旋压过程,应用仿真软件对翻边成形进行仿真,掌握了薄壁大尺寸铌钨合金喷管精密旋压及翻边成形技术.     

Performance analysis and application on Ti-6Al-4V of micro-forging system

Micro-forging (MF) is a novel surface modification technology which is capable of smoothening and strengthening the workpiece surface simultaneously. Based on analysis of the mechanism and energy conversion of micro-forging process, an electromagnetically driven micro-forging system is developed. To further grasp the kinetic characteristic of the equipment, a simulation model is established and its accuracy is verified. With the help of simulation and experimental results, we propose an input voltage optimization method, which drives the micro-forging head moving in a uniform and stable way. In this study, the influence of MF on surface integrity of Ti-6Al-4V (TC4) is firstly reported. Experimental results show that MF treatment reduces surface roughness (R_a) and increases micro-hardness by 48% and 11.8% at most, respectively. Besides, a compressive stress layer with an amplitude of −1000 MPa and a depth of 0.8 mm is observed. This study analyzes the performance and reveals the potential of micro-forging technology, which lays a solid foundation for expanding its application in TC4 surface modification.     

固溶时效处理对高强高韧钛合金显微组织与力学性能的影响

对固溶时效处理后的高强高韧钛合金初生α相的体积分数、尺寸,次生α相的体积分数和α_s/β相界面密度等显微组织特征进行了定量表征和统计分析,探讨了随着固溶温度的变化,高强高韧钛合金显微组织与其力学性能间的相关性.结果表明:在α+β两相区固溶时效处理,随着固溶温度的升高,合金初生α相的体积分数降低,相尺寸先降低后略有升高,次生α相的体积分数升高,α_s/β相界面密度先升高后降低.初生α相的体积分数与伸长率、静力韧度和裂纹形成功正相关,α_s/β相界面密度与合金屈服强度成正相关.      

基于Deform软件二次开发和BP神经网络的TA15多向锻造微观组织预报

通过热压缩实验构建了TA15合金的热变形真应力-应变曲线,以此为基础分别建立了合金双相区及单相区温度区间的热变形本构方程;基于热压缩试样动态再结晶的统计数据建立了TA15合金的动态再结晶模型。借助Deform提供的二次开发功能实现相关数学模型的程序化,制定正交实验方案,实现了TA15合金多向锻造变形的微观组织仿真。通过正交实验分析得出各项因子的影响对象及强弱差异,提出了双相区及单相区温度区间内的多向锻造最佳因子组合。建立了TA15合金多向锻造变形微观组织的BP （Back Propagation）神经网络预测模型,将预测结果与有限元仿真结果进行比较,结果表明两种方法的预测结果基本一致,但神经网络具备有限元仿真难以实现的良好细节预测能力,能更为细致地实现对微观组织分布状态的划分。     

Precipitation behavior and properties of extruded 7136 aluminum alloy under different aging treatments

In this work, the mechanical properties and electrical conductivity of the extruded 7136 aluminum alloy treated by single-stage aging treatment (T6), retrogression and re-aging treatment (RRA), and multiple retrogression and re-aging treatment have been investigated by means of hardness measurements, electrical conductivity tests and tensile tests. The results have shown that the properties of the 7136 alloy such as hardness, tensile strength and electrical conductivity were sensitive to retrogression time (within 90 min). With prolonging the retrogression time, the tensile strength was enhanced first and then decreased, yet the electrical conductivity was continuously increased. The 60 min-treated alloy performed the highest tensile strength (716 MPa), whereas the 90 min-treated alloy possessed the highest electrical conductivity (33.95%IACS). Compared with the T6-treated alloy, the tensile strength and electrical conductivity were improved by 3.3% and 18.9%, respectively. The electrical conductivity showed an obvious increase with repetitious times of the RRA treatment. After 3RRA60 treatment, a good combination of tensile strength (705 MPa) and electrical conductivity (33.20%IACS) can be obtained. Compared with the T6 condition, the tensile strength and electrical conductivity were improved by 1.7% and 16.3%, respectively. The mechanism of microstructure evolution under different aging treatments has been discussed in detail.     

含金属相变材料温控组件的研究

研究使用一种含有金属相变材料（Phase Change material,PCM）的温控组件（Thermal Control Component,TCC）对航天器上的有效载荷进行温度控制。通过对载荷的温控需求分析,设计并制备了以Ga-Sn合金为PCM的TCC,并通过地面模拟实验对TCC的温控性能进行测试。实验结果表明这种含有Ga-Sn合金的TCC满足载荷的温控需求。最后在仿真软件中建立了TCC的相变传热仿真模型用于预测TCC的温控性能。结果表明：仿真模型计算所得结果与实验结果基本一致,可用于预测TCC的温控性能。     

低合金钢管的焊接工艺及缺陷预防

采用氩弧焊打底,焊条电弧焊填充盖面焊接Cr5Mn低合金钢管,钢管壁厚为12mm,焊接位置为水平固定全位置焊接,在焊接之前,调整好焊接工艺参数,焊接完毕以后,对焊缝外观检验和X射线无损检测,发现焊缝的表面出现少量微裂纹,内部有少量气孔。为了保证焊缝的质量,对缺陷产生的原因进行分析并且采取正确的焊接工艺方法避免焊接缺陷。     

TC4-DT钛合金磨削表面特性及其摩擦磨损性能

钛合金是一种典型难磨削加工材料,磨削表面易出现烧伤、裂纹等热损伤。本文开展了TC4-DT钛合金磨削实验,通过扫描电镜（SEM）、能谱（EDS）、X射线衍射（XRD）、显微硬度仪、金相显微镜及球-盘摩擦磨损实验仪研究了其表面特性及摩擦磨损性能。结果表明：低速磨削表面质量好,摩擦磨损性能较基体略提高;当砂轮线速度为80 m/s时,磨削表面质量良好,摩擦系数为0.38,较基体降低40%;而砂轮线速度为100 m/s时,磨削表面出现严重烧伤、网状裂纹。因此选择合理的高速磨削工艺可避免烧伤、裂纹等热损伤缺陷,并可有效改善表面摩擦磨损性能;磨削表面干摩擦磨损机制为磨粒磨损、粘着磨损和剥层磨损。