连续式风洞二喉道调节马赫数控制策略

为了降低连续式跨超声速风洞压力波动,提高马赫数稳定性,需要对二喉道调节马赫数控制方式进行研究,针对现有文献鲜少对该控制策略描述等问题,以0.6m连续式跨声速风洞为例,对二喉道控制马赫数的原理进行分析,基于运动控制器加伺服驱动器双PID(proportion-integral-derivative)控制模式实现二喉道位置精确控制,提出了二喉道和压缩机转速的组合控制流程,并采用分段变参数模糊PID加串级控制的算法实现马赫数精确控制,最后进行了试验验证。结果表明马赫数控制精度优于0.001,且每个马赫数极曲线(9个攻角阶梯)的时间可控制在4min以内,证明所提出的控制策略是有效的,可为连续式跨超声速风洞的设计调试提供参考。      

一种低轨双星雷达信号无模糊频差估计算法

针对低轨双星组合接收低脉冲重复频率(LPRF)雷达信号的频差(DFO)估计存在模糊的问题，提出一种基于时差差分的频差无模糊高精度估计算法，该算法通过对高精度的时差测量值进行中心差分获得无模糊的频差估值。仿真结果表明，新算法能对PRF低至300 Hz的雷达信号进行无模糊的频差估计，估计精度在信噪比高于15 dB时逼近克拉美劳下界，可有效扩大低轨双星时/频差定位系统对LPRF信号的适用范围。     

涡轮导向叶片综合冷却效率实验研究

为了研究流动参数对涡轮导向叶片综合冷却效率的影响,采用红外热像仪对叶片表面的温度分布进行了测量,得到了叶片的综合冷却效率随流量比、温比、主流进口雷诺数和湍流度的变化规律。实验过程中,次流与主流的流量比分别为0.15,0.18,0.20,0.22和0.24;主次流温比分别为1.4,1.7,1.93和2.2;主流进口雷诺数分别为1.0×10~5,1.1×10~5,1.2×10~5,1.3×10~5和1.4×10~5;主流进口湍流度分别为0.506%,8.156%,14.92%。结果表明,综合冷却效率在前缘处最低,沿流向逐渐升高;增大流量比会显著提高叶片的综合冷却效率,在温比为1.93时,流量比由0.15增大至0.24,综合冷却效率平均增加29.3%;温比和主流进口湍流度的增大均不利于综合冷却效率的提升,流量比为0.20时,温比由1.4增大至2.2,综合冷却效率平均下降46.5%,湍流度由0.506%增大至14.92%,综合冷却效率平均降低15.5%;主流进口雷诺数对叶片综合冷却效率的影响很小。     

大型客机低速构型高雷诺数风洞腹撑支架干扰数值模拟

风洞到飞行相关性修正是获取现代大型客机低速气动特性的重要手段，通常采用增压提高风洞试验雷诺数，而支架干扰修正是该修正体系的一个关键环节。采用数值模拟研究了增压风洞腹撑的支架干扰，并分析了腹撑对飞机各部件的干扰及其对风洞流场的影响。通过数值模拟与风洞试验对比，表明升力系数相差0.006，阻力系数最大相差0.001 2，俯仰力矩系数最大相差0.01，验证了CFD数值模拟方法的可靠性。CFD计算结果表明：腹撑使得全机升力增加、阻力减小，俯仰力矩增加；腹撑对升力影响的主要部件是机翼，腹撑使得风洞中心以上动压增加，提升上翼面流速，从而增加了机翼的升力；与传统认识不同的是腹撑对阻力影响为负，且主要影响部件为缝翼，原因为缝翼下偏使得法矢分量向前从而减小了阻力；腹撑对俯仰力矩影响的主要部件是机身及平尾。研究结果揭示了腹撑对飞机气动特性影响的量级、主要影响部件及其流场变化，可为支架干扰数据修正及支架优化设计提供参考。所得结论可更好用于支架干扰试验的开展及风洞到飞行数据的修正，具有一定的工程实用性。     

翼型低雷诺数层流分离现象随雷诺数的演化特征

层流分离现象是翼型低雷诺数条件下出现的典型流场特征。层流分离流动中包含流动分离、转捩、再附等非定常流动结构，层流分离流动的形成与演化会对翼型气动特性产生恶化作用。采用大涡模拟（LES）方法对低雷诺数范围内不同雷诺数下的翼型层流分离流动开展精细数值模拟，研究了雷诺数对翼型气动特性的影响规律及作用机理。LES方法采用隐式亚格子模型，基于结构化拼接网格，对流项离散和时间推进方法分别采用AUSM⁺格式以及双时间步方法。验证算例计算结果表明数值模拟方法的正确性及可靠性，雷诺数对翼型气动特性具有显著影响。随雷诺数降低，时均分离泡外形增大、位置后移，平均阻力系数增大，特别是在较低雷诺数下，翼型升阻力系数随时间出现振荡现象。进一步研究表明，造成不同时均分离泡形态和气动特性的原因在于翼型上表面分离剪切层的失稳与转捩特征。随雷诺数降低，流动黏性增大，导致分离剪切层速度梯度减小，流动发生转捩及再附位置后移，直至翼型表面不再发生转捩和再附。     

Assessment study of ionosphere correction model using single- and multi-shell algorithms approach over sub-Saharan African region

It is a known fact that ionosphere is the largest and the least predictable among the sources of error limiting the reliability and accuracy of Global Navigation Satellite Systems (GNSS) and its regional augmentation systems like Satellite Based Augmentation System (SBAS) in a safety-of-life application. The situation becomes worse in the Equatorial Ionization Anomaly (EIA) region, where the daytime ionization distribution is modified by the fountain effect that develops a crest of electron density at around ±15° to ±20° of the magnetic equator and a trough at the magnetic equator during the local noon hours. Related to this phenomenon is the appearance of ionosphere irregularities and plasma bubbles after local sunset. These may degrade further the quality of service obtained from the GNSS/SBAS system of the said periods. Considering the present operational augmentation systems, the accuracy and integrity of the ionosphere corrections estimate decreases as the level of disturbances increases. In order to provide a correct ionosphere correction to the user of GNSS operating in African EIA region and meet the integrity requirements, a certified ionosphere correction model that accurately characterizes EIA gradient with the full capacity to over-bound the residual error will be needed. An irregularities detector and a decorrelation adaptor are essential in an algorithm usable for African sub-Saharan SBAS operation. The algorithm should be able to cater to the equatorial plasma vertical drifts, diurnal and seasonal variability of the ionosphere electron density and also should take into account the large spatial and temporal gradients in the region. This study presents the assessment of the ionosphere threat model with single and multi-layer algorithm, using modified planar fit and Kriging approaches.     

Analytical Calculation Model for Mach Wave Parameters

When a wave shaper is embedded in a liner,Mach wave will emerge above the liner,which affects the head shape of an explosively formed projectile.Mach wave parameters,including radius and pressure need to be determined to effectively match Mach wave with the liner,so that a good head shape can be obtained.An analytical calculation model for Mach wave parameter is presented based on three-shock theory,and the theoretical values agree well with the experimental ones.The analysis shows that when the radius of the wave shaper is constant,the radius of the Mach wave increases,whereas the pressure decreases while increasing the distance between the liner and the wave shaper.When the distance between the liner and the wave shaper is constant,the radius of the Mach wave increases,whereas the pressure decreases when decreasing the radius of the wave shaper.     

Effects of in-track maneuver on Sun illumination conditions of near-circular low Earth orbits

By developing approximate analytical models considering the J₂ perturbation, the effects of an in-track maneuver on the orbital Sun illumination conditions of near-circular low Earth orbits are analyzed. First, two approximate models for the variations in orbital sunshine angles are developed, one for variations at a given time and the other for variations at a given argument of latitude. Next, two approximate models for variations in orbital arc in Earth shadow are developed, one considers the small eccentricity and the other uses the zero eccentricity. Finally, the developed approximate models are applied to analyzing the Sun illumination conditions of a typical in-track maneuver mission on a near-circular low Earth orbit. From the results obtained, three major conclusions can be drawn. First, the variations in orbital sunshine angles at a given time may reach tens of degrees when the drifting time reaches hundreds of orbital periods, and the approximate model for that situation cannot effectively approach the numerical results. Second, the variations in orbital sunshine angles for any given argument of latitude are only a couple of degrees even when the drifting time reaches 500 orbital periods, and the approximation model developed can effectively approach the numerical results. Third, for variations in orbital arc in Earth shadow, the approximate model considering the small eccentricity has simple expressions and can effectively approach the numerical results; in contrast, the approximate model using the zero eccentricity has relatively worse precision.     

重型燃气轮机高雷诺数CDA叶型转捩特性数值计算

为研究重型燃气轮机的压气机叶片在高雷诺数工况下的气动性能,基于Gamma-Theta转捩模型的雷诺时均方程对某可 控扩散叶型进行了数值计算。通过对比不控制马赫数与控制马赫数,分析高雷诺数对可控扩散叶型气动性能及转捩特性的影响。 结果表明：在不控制马赫数条件下,在零攻角时,雷诺数从7×10 5 增大为9×10 5 ,总压损失增加了约391.95%;在高雷诺数工况下随 着雷诺数的增大,叶片流动损失不断增大,叶片可用攻角范围减小,同时在叶片吸力面出现激波,干扰转捩的产生。在控制马赫数 条件下,当Ma=0.6时,在零攻角工况下,雷诺数从8.2×10 5 增大为1×10 7 ,总压损失减小了约38.98%,吸力面转捩起始点从4.78%弦 长处前移至1.11%弦长处;在高雷诺数工况下,叶片流动损失随着雷诺数的增大不断减小,吸力面转捩位置前移。     

低雷诺数仿生分离流翼型气动特性初探

为了探索适合低雷诺数微型飞行器的翼型形式,基于对自然界鸟类和昆虫滑翔飞行时翅膀形状的观察,设计出一种由前缘削尖平板和后缘圆弧翼型组合而成的仿生分离流翼型。数值研究结果表明,气流在削尖平板的前缘点强制分离,形成大范围低压分离流动,随后在后部圆弧翼上表面再附形成稳定低压涡流区,从而实现较高的气动效率和较强的抵抗大气湍流的能力。上削尖平板可以使流动分离点固定在削尖点。相对于单独平板,仿生分离流翼型的升力系数有大幅提高,迎角为4°时提高了112%。此外,仿生分离流翼型可以在较宽的迎角范围内（4°~20°）保持高升力,但是迎角增加,阻力也快速增大,因此小迎角情况下（小于4°）气动效率更优。