气动参数对后台阶三维缝隙换热影响的研究

针对涡轮叶片尾缘冷却结构特点,建立了后台阶三维缝隙结构气膜冷却特性试验台,测量了缝隙中心和肋中心下游换热系数的局部分布,研究了不同雷诺数Re(5000~15000)与吹风比Br(0.5~2.0)对换热系数的影响规律,试验结果表明:(1)出口的换热系数总体呈下降趋势,但在肋后中心线略有起伏;(2)随着Re的增大,换热系数增大,随着Br的增大,换热系数减小;(3)在靠近出口位置,由于热边界层与三维掺混特性流场的影响,使得换热变得复杂。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

MOCVI制备Nextel 720/SiO2复合材

研究了MOCVI(MetalOrganicChemicalVaporInfiltration)方法制备Nextel720/SiO     

轴对称突扩直管流场计算

本文是为喷管喉部沉积问题的研究而进行的喷管突扩流场研究工作的一部分,重点研究了产生突扩流效应的轴对称直管流场.在等粘度和k-ε紊流模型下,分别计算了三种速度分布下的流场,和国内外相关实验结果及Spalding,D.B.的计算结果进行比较,取得了满意的结果.同时考察了动边界下流场的变化,实现了突扩流效应的理论预测.本文考察了SIMPLE方法.在源项处理、方程的非线性、方程的解法等方面做了分析研究和计算工作,解决了一些具体应用问题.     

计算机辅助计划管理和决策总体设计

 介绍一种新机研制计划管理和决策支持系统的总体设计方案及其实现的具体措施。详细介绍了几个主要模块的设计思想。     

Kinetic Monte Carlo Simulation of EB-PVD Film:Effects of Substrate Temperature

The 2D kinetic Monte Carlo (KMC) simulation was used to study the effects of different substrate temperatures on the microstruc-ture of Ni-Cr films in the process of deposition by the electron beam physical vapor deposition (EB-PVD). In the KMC model, substrate was assumed to be a “surface” of tight-packed rows, and the simulation includes two phenomena: adatom-surface collision and adatom diffusion. While the interaction between atoms was described by the embedded atom method, the jumping energy was calculated by the molecular static (MS) calculation. The initial location of the adatom was defined by the Momentum Scheme. The results reveal that there exists a critical substrate temperature which means that the lowest packing density and the highest surface roughness structure will be achieved when the temperature is lower than the smaller critical value, while the roughness of both surfaces and the void contents keep decreasing with the substrate temperature increasing until it reaches the higher critical value. The results also indicate that the critical substrate temperature rises as the deposition rate increases.     

高密度喷气燃料与常规喷气燃料浓度场试验研究

本文利用ＣＯ２红外气体分析仪和取样管对高密度喷燃料和常规喷气燃料在直流喷嘴下游的浓度场分布进行了测量，就气流速度，油压降和下游距离对浓度场分布的影响进行了对比研究。试验结果表明，在相同工况下，常规喷气燃料的最大浓度值比高密度喷气燃料的大；气流速度和油压变化对高密度喷气燃料最大浓度点穿透深度的影响大于对常规喷气燃料的影响。     

热暴露对B/Al复合材料性能的影响

对经300℃、500℃高温热暴露的B／Al（LF6）复合材料的力学性能进行了研究，实验结果表明材料在300℃下热暴露时，性能下降速度较慢，100h后强度保留率约为76％，延伸率保留率为74％。而在500℃下热暴露时，5h以上强度就有明显降低。高温长时间热暴露后复合材料的断裂也从积累型转变为典型的非累积型断裂。通过透射电镜（TEM）及扫描电镜（SEM）对固态热压制造态和主温热暴露的界面状况进行了分析，认为界面反应是造成B／Al复合材料力学性能下降的主要原因。     

嵌入式网关技术在门禁控制系统中的应用

随着计算机网络技术的发展和普及，目前出现了以单片机技术和以太网技术为核心的嵌入式网关技术，采用嵌入网关技术，可在局域网环境下采用TCP/IP协议实现门禁控制控制器同后台服务器的数据交换。其优点是技术先进、数据传输速度高、工程成本低、可靠性和安全性高。在论述了嵌入式网关工作原理的基础上，重点讨论了嵌入式网关中的门禁控制器的应用问题。