多喷嘴构型的轴对称氢氧加热器设计与仿真

为了使氢氧燃烧加热器满足自由射流试验台工作需要并获得均匀的出口气流参数,采用同轴剪切式7个喷嘴轴对称构型喷注器,利用CFD仿真软件对其进行了三维反应流场计算,燃烧模型采用氢氧单步反应模型,获得了设计工况下的参数.计算结果表明:燃烧效率随着中心喷嘴与外围喷嘴距离L与喷注面板半径R之比(L/R)的增大先上升后下降;喷注面板的温度随着L/R的增大而降低,最终维持在600K左右;加热器出口的氧气摩尔分数以及总温的均匀性基本不随着L/R变化而变化;出口主流区的马赫数在6左右满足设计要求.在各个喷嘴的影响区域大致相等时,加热器综合性能良好.氢氧速度比越大,完全燃烧所需区域越短,喷注面板温度越高.与单喷嘴、19个喷嘴的加热器比较发现7个喷嘴的构型较为合理.      

航空碳纤维树脂基复合材料加筋板压缩屈曲及后屈曲性能

开展了复合材料加筋板轴压稳定性实验,对加筋板的屈曲及后屈曲性能、破坏模式和后屈曲失效表征进行了研究.实验结果表明加筋板在轴压下具有良好后屈曲承载潜能,破坏载荷约为屈曲载荷的2.2倍;其屈曲模式为筋条间蒙皮首先发生屈曲失稳,筋条在整个承载过程中保持直线,起到“屈曲分隔”的作用.通过对加筋板屈曲及后屈曲性能的理论分析,得出的理论屈曲载荷和理论破坏载荷与实验结果相对误差均小于8%,并确定了在后屈曲过程中蒙皮中心挠度的变化规律和轴向载荷的面内分布特征.      

Streamwise-body-force-model for rapid simulation combining internal and external flow fields

A streamwise-body-force-model (SBFM) is developed and applied in the overall flow simulation for the distributed propulsion system, combining internal and external flow fields. In view of axial stage effects, fan or compressor effects could be simplified as body forces along the streamline. These body forces which are functions of local parameters could be added as source terms in Navier-Stokes equations to replace solid boundary conditions of blades and hubs. The val-idation of SBFM with uniform inlet and distortion inlet of compressors shows that pressure perfor-mance characteristics agree well with experimental data. A three-dimensional simulation of the integration configuration, via a blended wing body aircraft with a distributed propulsion system using the SBFM, has been completed. Lift coefficient and drag coefficient agree well with wind tun-nel test results. Results show that to reach the goal of rapid integrated simulation combining inter-nal and external flow fields, the computational fluid dynamics method based on SBFM is reasonable.     

A new steering approach for VSCMGs with high precision

A new variable speed control moment gyro (VSCMG) steering law is proposed in order to achieve higher torque precision. The dynamics of VSCMGs is established, and two work modes are then designed according to command torque:control momentum gyro (CMG)/reaction wheel (RW) hybrid mode for the large torque case and RW single mode for the small. When working in the CMG/RW hybrid mode, the steering law deals with the gimbal dead-zone nonlinearity through compensation by RW sub-mode. This is in contrast to the conventional CMG singularity avoidance and wheel speed equalization, as well as the proof of definitely hyperbolic singular property of the CMG sub-mode. When working in the RW single mode, the motion of gimbals will be locked. Both the transition from CMG/RW hybrid mode to RW single mode and the reverse are studied. During the transition, wheel speed equalization and singularity avoidance of both the CMG and RW sub-modes are considered. A steering law for the RWs with locked gimbals is presented. It is shown by simulations that the VSCMGs with this new steering law could reach a better torque precision than the normal CMGs in the case of both large and small torques.     

航空复合材料加筋板压缩屈曲及后屈曲力学性能

航空复合材料加筋板由于具有良好的力学性能,广泛地应用于航空结构中。本工作研究了航空复合材料加筋板压缩屈曲及后屈曲力学性能,首先应用工程方法对复合材料加筋板进行压缩稳定性计算,得到加筋板的屈曲载荷和破坏载荷的预估值;其次,开展复合材料加筋板压缩稳定性实验,得到实验件的屈曲及破坏形式、实验件的载荷-应变及载荷-位移关系和实验件的屈曲载荷和破坏载荷。结果表明:采用工程方法得到的计算结果与实验结果较为吻合,屈曲载荷和破坏载荷的误差分别为6.12%和9.31%,合理应用工程方法可以为实验提供较好的指导;加筋板的破坏形式为壁板的分层、鼓包和撕裂、筋条的断裂以及筋条-壁板的脱粘;屈曲比为1.65的复合材料加筋板具有较强的后屈曲承载能力;工程中可充分应用加筋板的后屈曲承载能力提高结构的利用效率。     

Drag derived altitude aided navigation method

The navigation problem of the lifting reentry vehicles has attracted much research interest in the past decade.This paper researches the navigation in the blackout zone during the reentry phase of the aircraft,when the communication signals are attenuated and even interrupted by the blackout zone.However,when calculating altitude,a pure classic inertial navigation algorithm appears imprecise and divergent.In order to obtain a more precise aircraft altitude,this paper applies an integrated navigation method based on inertial navigation algorithms,which uses drag derived altitude to aid the inertial navigation during the blackout zone.This method can overcome the shortcomings of the inertial navigation system and improve the navigation accuracy.To further improve the navigation accuracy,the applicable condition and the main error factors,such as the atmospheric coefficient error and drag coefficient error are analyzed in detail.Then the damping circuit design of the navigation control system and the damping coefficients determination is introduced.The feasibility of the method is verified by the typical reentry trajectory simulation,and the influence of the iterative times on the accuracy is analyzed.Simulation results show that iterative three times achieves the best effect.     

Protecting Earth-orbiting spacecraft against micro-meteoroid/orbital debris impact damage using composite structural systems and materials: An overview

Spacecraft that are launched to operate in Earth orbit are susceptible to impacts by meteoroids and pieces of orbital debris (MMOD). The effect of a MMOD particle impact on a spacecraft depends on where the impact occurs, the size, composition, and speed of the impacting object, the function of the impacted system. In order to perform a risk analysis for a particular spacecraft under a specific mission profile, it is important to know whether or not the impacting particle (or its remnants) will exit the rear of an impacted spacecraft wall. A variety of different ballistic limit equations (BLEs) have been developed for many different types of structural wall configurations. BLEs can be used to optimize the design of spacecraft wall parameters so that the resulting configuration is able to withstand the anticipated variety of on-orbit high-speed impact scenarios. While the level of effort exerted in studying the response of metallic multi-wall systems to high speed particle impact is quite substantial, the extent of the effort to study composite material and composite structural systems under similar impact conditions has been much more limited. This paper presents an overview of the activities performed to assess the resiliency of composite structures and materials under high speed projectile impact. The activities reviewed will be those that have been aimed at increasing the level of protection afforded to spacecraft operating in the MMOD environment, and more specifically, on those activities performed to mitigate the mechanical and structural effects of an MMOD impact.     

Matching suitable feature construction for SAR images based on evolutionary synthesis strategy

In the paper,a set of algorithms to construct synthetic aperture radar（SAR）matching suitable features are frstly proposed based on the evolutionary synthesis strategy.During the process,on the one hand,the indexes of primary matching suitable features（PMSFs）are designed based on the characteristics of image texture,SAR imaging and SAR matching algorithm,which is a process involving expertise;on the other hand,by designing a synthesized operation expression tree based on PMSFs,a much more flexible expression form of synthesized features is built,which greatly expands the construction space.Then,the genetic algorithm-based optimized searching process is employed to search the synthesized matching suitable feature（SMSF）with the highest effciency,largely improving the optimized searching effciency.In addition,the experimental results of the airborne synthetic aperture radar ortho-images of C-band and P-band show that the SMSFs gained via the algorithms can reflect the matching suitability of SAR images accurately and the matching probabilities of selected matching suitable areas of ortho-images could reach 99±0.5%.     

翼尖装置优化设计研究

使用面元法气动分析软件VSAERO对机翼与翼梢小翼组合体模型进行数值模拟,并采用Steve Smith提出的诱导阻力优化方法对翼梢小翼的定位进行优化设计。结果表明,能够有效地预测出翼梢小翼的最优定位,在翼梢小翼优化设计中具有很好的适用性。     

复合材料加筋壁板制造成本的快速估算模型

为了能够在设计阶段早期对复合材料加筋壁板制造成本进行快速估算,提出了一种以结构设计重量为主要驱动因素的制造成本估算模型。该模型的关键是考虑了诸如材料成本比重系数、制造工艺系数、蒙皮形状系数、筋条形状系数、材料利用率系数等合理取值。以某验证试验的试验件制造成本估算为例,估算成本与实际制造成本的偏差为10.8%,说明了采用该方法对复合材料加筋壁板制造成本进行快速估算的结果是可以为设计人员提供决策依据的。