端壁附面层抽吸对大转角扩压叶栅旋涡影响的实验研究

为探明附面层抽吸技术对压气机叶栅气动性能的影响及其与栅内旋涡结构的关联,通过十个横截面的实验测量结果研究了高负荷压气机叶栅抽吸端壁附面层前后的主要旋涡结构以其对应损失的演变过程。研究对象为矩形低速扩压叶栅,来流马赫数约为0.23。研究结果表明,端壁附面层的变化对叶栅端区的主要旋涡发展过程影响显著。在原型方案中,壁面涡、尾缘脱落涡的演变过程对应着较高的流动损失,通道涡自身产生的损失较小,主要起到向远离端壁的方向输运低能流体的作用;在流向槽吸气方案中,壁面涡和尾缘脱落涡因端壁附面层径向迁移及角区分离受到抑制而被明显削弱;而来流附面层抽吸方案则最为有效地控制了通道涡的演变过程。      

气氧/甲烷涡流冷壁燃烧室流场与壁面耦合传热分析

针对涡流燃烧室的试验模型,耦合计算了其中的燃烧、流动和传热过程。湍流模型采用RNG k-ε两方程模型,辐射传热采用P1辐射模型,化学反应采用有限速率模型。数值模拟了涡流燃烧室在20s内的传热过程,得到了燃烧室和喷管的壁面温度分布随时间的变化。燃烧室侧壁面和头部温度在4秒内就达到较稳定状态,在涡流保护下侧壁面最高温度在650K左右,头部最高温度在785K左右。对于热沉喷管,壁面温度随时间基本呈缓慢线性上升,在一定的时间内可以满足实验要求。     

Individual influence of pitching and plunging motions on flow structures over an airfoil during dynamic stall

The individual influence of pitching and plunging motions on flow structures is studied experimentally by changing the phase lag between the geometrical angle of attack and the plunging angle of attack. Five phase lags are chosen as the experimental parameters, while the Strouhal number, the reduced frequency and the Reynolds number are fixed. During the motion of the airfoil, the leading edge vortex, the reattached vortex and the secondary vortex are observed in the flow field. The leading edge vortex is found to be the main flow structure through the proper orthogonal decomposition. The increase of phase lag results in the increase of the leading edge velocity, which strongly influences the leading edge shear layer and the leading edge vortex. The plunging motion contributes to the development of the leading edge shear layer, while the pitching motion is the key reason for instability of the leading edge shear layer. It is also found that a certain increase of phase lag, around 34.15° in this research, can increase the airfoil lift.     

Effects of coarse riblets on air flow structures over a slender delta wing using particle image velocimetry

This research investigates the aerodynamic performance and flow characteristics of a delta wing with 65° sweep angle and with coarse axial riblets,and then compares with that of a smooth-surface delta wing.Particle Image Velocimetry(PIV)were utilized to visualize the flow over the wing at 6 cross-sections upright to the wing surface and parallel to the wing span,as well as 3 longitudinal sections on the leading edge,symmetry plane,and a plane between them at Angles of Attack(AOA)=20°and 30°and Re=1.2×10~5,2.4×10~5,and 3.6×10~5.The effects of the riblets were studied on the vortices diameter,vortex breakdown location,vortices distance from the wing surface,flow lines pattern nearby the wing,circulation distribution,and separation.The results show that the textured model has a positive effect on some of the parameters related to drag reduction and lift increase.The riblets increase the flow momentum near the wing’s upper surface except near the apex.They also increase the flow momentum behind the wing.     

飞行器阵风响应的CFD-6DOF仿真分析

飞行器在大气中飞行,不可避免地受到阵风的影响。阵风所附加的气动载荷引发飞行器飞行状态的改变,过大幅值的阵风影响飞行的性能与安全。针对这种状况,首先采用改进的Lamb-Ossen涡模型,建立尾涡形式的阵风场;然后采用基于CFD技术的非定常N-S方程求解,并在计算网格中引入"网格速度"来模拟阵风,对SWIM(Subsonic Wall Interference Model)尾涡中的定常气动特性进行验证;最后通过CFD-6DOF的耦合,对SWIM俯冲穿越尾涡场的飞行轨迹进行研究。结果表明:计算结果与实验值符合较好;SWIM在尾涡中飞行时出现抖动、下沉、改变飞行状态、剧烈翻转的现象,与实际飞行器进入尾涡中的轨迹特性类似。     

磁粉探伤中的涡流效应

首先计算棒材通交流电磁化时其中的涡流及磁场分布，由微机绘制相应的分布曲线，最后讨论因涡流效应对磁化的影响并得出了一些有关结论。     

过山气流的一种工程模拟方法

给出了一种过山气流的流体力学工程化模型。它根据过山气流的流动特点，按照绕圆柱流动理论，计入地面摩擦影响，同时用叠加背风涡的方法，     

Influence of thermal inhibitor position and temperature on vortex-shedding-driven pressure oscillations

Vortex-acoustic coupling is one of the most important potential sources of combustion instability in solid rocket motors (SRMs). Based on the Von Karman Institute for Fluid Dynamics (VKI) experimental motor, the influence of the thermal inhibitor position and temperature on vortex-shedding-driven pressure oscillations is numerically studied via the large eddy simulation (LES) method. The simulation results demonstrate that vortex shedding is a periodic process and its accurate frequency can be numerically obtained. Acoustic modes could be easily excited by vortex shedding. The vortex shedding frequency and second acoustic frequency dominate the pressure oscillation characteristics in the chamber. Thermal inhibitor position and gas temperature have little effect on vortex shedding frequency, but have great impact on pressure oscillation amplitude. Pressure amplitude is much higher when the thermal inhibitor locates at the acoustic velocity anti-nodes. The farther the thermal inhibitor is to the nozzle head, the more vortex energy would be dissipated by the turbulence. Therefore, the vortex shedding amplitude at the second acoustic velocity antinode near 3/4L (L is chamber length) is larger than those of others. Besides, the natural acoustic frequencies increase with the gas temperature. As the vortex shedding frequency departs from the natural acoustic frequency, the vortex-acoustic feedback loop is decoupled. Consequently, both the vortex shedding and acoustic amplitudes decrease rapidly.     

一种采用径向串联方式的组合旋涡泵设计方法

给出了一种采用径向串联方式的两级组合旋涡泵设计方法.该方法首先使用经验系数法对旋涡泵的结构参数进行初步设计,然后采用Hex/Wedge网格单元划分Proe所建立的旋涡泵三维模型的网格;进而通过CFD数值模拟反复迭代优化得出旋涡泵的最终结构参数;最后对组合旋涡泵内流场进行了仿真分析并与试验数据进行了对比分析.对比分析表明在设计点仿真数据与试验数据的相对误差不超过2％,所设计的两级组合旋涡泵达到了预期性能指标.表明该设计方法是可行、有效的.     

涡流发生器控制喷水推进器进水管流动分离的数值研究

为抑制某型喷水推进平入口进水管低进速比下管内流动分离,提升喷射泵来流的品质,应用涡流发生器（VG）流动控制技术,在进水管内部以及入口前的船底加装涡流发生器。采用雷诺时均模型和SST-kω湍流模型数值模拟进水管内流场,从流动分离、涡系分布和整体性能等方面分析了不同位置VG对进水管流场特性的影响,揭示了VG抑制进水管流动分离的控制机理。结果表明,VG产生流向涡驱动主流与斜坡侧边界层低能流体进行动量交换,增加边界层内的流向动量,从而抑制进水管斜坡侧的流动分离。流向涡在分离区内会发生方向偏移导致进水管内流场不对称。VG在进水管内产生的流向涡强度以及自身附加损失都会影响其控制效果。通过优选VG安装位置,进水管出口的不均匀度系数从0.406下降至0.318,旋流度从3.23°下降至2.14°,出口总压畸变减小,整体效率得到有效提升。