全文获取类型
收费全文 | 738篇 |
免费 | 477篇 |
国内免费 | 89篇 |
专业分类
航空 | 740篇 |
航天技术 | 224篇 |
综合类 | 31篇 |
航天 | 309篇 |
出版年
2024年 | 8篇 |
2023年 | 21篇 |
2022年 | 38篇 |
2021年 | 62篇 |
2020年 | 46篇 |
2019年 | 40篇 |
2018年 | 38篇 |
2017年 | 24篇 |
2016年 | 33篇 |
2015年 | 26篇 |
2014年 | 75篇 |
2013年 | 70篇 |
2012年 | 54篇 |
2011年 | 74篇 |
2010年 | 55篇 |
2009年 | 35篇 |
2008年 | 28篇 |
2007年 | 72篇 |
2006年 | 61篇 |
2005年 | 51篇 |
2004年 | 40篇 |
2003年 | 34篇 |
2002年 | 39篇 |
2001年 | 32篇 |
2000年 | 21篇 |
1999年 | 37篇 |
1998年 | 33篇 |
1997年 | 26篇 |
1996年 | 22篇 |
1995年 | 22篇 |
1994年 | 14篇 |
1993年 | 15篇 |
1992年 | 8篇 |
1991年 | 15篇 |
1990年 | 9篇 |
1989年 | 7篇 |
1988年 | 8篇 |
1987年 | 11篇 |
排序方式: 共有1304条查询结果,搜索用时 453 毫秒
41.
姜贵庆%张学军%王淑华%艾邦成%俞继军 《宇航材料工艺》2007,37(4):8-11
在分析尖化前缘热环境特性的基础上,给出了尖化前缘相应的热结构特性的计算和分析,分析结果表明:尖化前缘热流密度在2~3个自由程内下降到原来的1/3,而表面温度仅有10%的下降;高热导率的防热材料可降低前缘的最高表面温度,对非烧蚀热防护十分有利,它还可提高后部的表面温度,增加辐射散热的力度,这是非烧蚀热防护的重要机制. 相似文献
42.
用热分析法(DTA)研究了纳米金属和复合金属粉(Cu,N i,A l,N iCu,N iCuB,N iB)对AP/HTPB推进剂热分解的影响。结果表明,纳米金属和复合金属粉对HTPB推进剂的热分解具有明显的催化作用。纳米铜粉使AP/HTPB推进剂的低温和高温热分解温度分别降低了51.6℃和33.6℃,DTA表观分解热增大为3.7kJ.g-1,催化效果十分显著。纳米铜粉和含铜的纳米复合金属粉(N iCu和N iCuB)的催化效果强于其他纳米金属粉。纳米金属粉主要通过催化AP/HTPB推进剂中AP的热分解,表现出对HTPB推进剂具有较好的催化效果。 相似文献
43.
本文叙述了金属基复合材料热循环损伤的动态共振检测方法,利用该方法对B/Al、SiCf/Al和C/Mg等单向排列金属基复合热循环损伤进行了检测,得出一些结果,并进行了讨论。 相似文献
44.
对离心式喷嘴的最大流量原理进行了证明,并求得了该原理成立的边界条件。分析了离心式喷嘴的工况,结果表明,当喷嘴压降等于或大于临界截面处平均余区的1.5倍时,其工况处于临界或超临界状态。导出了波沿离心式喷嘴中液体自由表面的传播速度及其频率的计算公式,从中可以看出,波的传播速度及其频率取决于喷嘴压降及喷嘴的几何特性。 相似文献
45.
46.
47.
Wu Xianyu Li Xiaoshan Ding Meng Liu Weidong Wang Zhenguo 《中国航空学报》2007,20(6):488-494
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances. 相似文献
48.
张绪虎%胡欣华%关盛勇%汪翔%杨盛良 《宇航材料工艺》2001,31(2):48-55
对经300℃、500℃高温热暴露的B/Al(LF6)复合材料的力学性能进行了研究,实验结果表明材料在300℃下热暴露时,性能下降速度较慢,100h后强度保留率约为76%,延伸率保留率为74%。而在500℃下热暴露时,5h以上强度就有明显降低。高温长时间热暴露后复合材料的断裂也从积累型转变为典型的非累积型断裂。通过透射电镜(TEM)及扫描电镜(SEM)对固态热压制造态和主温热暴露的界面状况进行了分析,认为界面反应是造成B/Al复合材料力学性能下降的主要原因。 相似文献
49.
50.