多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

Electrochemical trepanning with uniform electrolyte flow around the entire blade profile

In the traditional machining process for diffusers, blades are easily deformed, and methods suffer from high tool wear and low efficiency. Electrochemical machining(ECM) possesses unique advantages when applied to these difficult-to-machine materials. In the ECM process, theflow field plays a crucial role. Here, an electrolyte flow mode that supplies uniform flow around the entire blade profile was adopted for electrochemical trepanning of diffusers. Various flow rates were employed to obtain the optimal flow field. Simulations were conducted using ANSYS software, and results indicated that increasing the flow rate substantially afforded a more uniform flowfield. A series of experiments was then performed, and results revealed that increasing the flow rate greatly improved both the machining efficiency and the surface quality of the diffusers. The maximum feeding rate of the cathode reached 4 mm/min, the blade taper of the concave part decreased to 0.02, and the blade roughness was reduced to 1.216 lm. The results of this study demonstrated the high feasibility of this method and its potential for machining other complex components for engineering applications.     

跨介质航行器波浪环境入水流场演变和运动特性研究

跨介质航行器是一种既可以在空中飞行又可以在水下潜航的新概念航行器,基于仿生学原理,提出一种通过改变外形实现水空介质跨越的航行器模型,通过入水试验装置和计算流体动力学方法,对航行器带攻角从空气到水的介质跨越过程进行了试验和数值仿真研究,得到了跨介质入水过程航行器的运动姿态和入水空泡形态,并通过数值仿真得到了航行器的升力、阻力、速度和加速度演化规律。同时基于数值模拟方法对有波浪情况和静水情况下航行器入水过程空泡演变以及运动特性进行对比。结果表明:提出的航行器构型在水中具有较好的姿态调整能力,波浪的有无和波高的不同都会对航行体入水运动特性造成影响。     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

直流电机网络控制系统仿真

对直流电机网络闭环控制系统进行仿真分析,根据电机网络闭环控制系统原理建立仿真模型。对具有数据丢包的直流电机网络伺服控制系统输出响应特性进行仿真,比较系统分别采用PI控制及增益,可调PI控制方式时的输出特性。结果表明,相比常规PI控制增益可调PI控制方法在网络环境下具有更好的控制特性。该研究为网络伺服控制技术提供可靠的参考依据。     

基于经济损失的航班延误恢复模型研究

分析了航班延误的恢复调度问题,并针对问题提出了一种机场大面积航班延误恢复模型,模型考虑了航班延误的延误时间,还考虑了不同机型对航班延误经济损失造成的影响。构造了基于免疫机制的免疫遗传算法来求解模型,此算法保留了标准遗传算法随机全局并行搜索的特点,又在相当大的程度上避免了未成熟收敛。用实际的航班信息进行仿真研究结果表明,文中的模型和算法切实可行。     

Sound insulation performance of plates with interconnected distributed piezoelectric patches

This paper deals with the sound insulation performance of a thin plate with intercon-nected distributed piezoelectric patches. Piezoelectric patches are periodically bonded on the sur-faces of the plate in a collocated fashion, and are interconnected via an inductive circuit network. This piezoelectric system is termed as piezo-electromechanical (PEM) plate in the paper. Homogenization methods are involved under a sub-wavelength assumption to analytically develop the dynamical equations for the PEM plate. The dispersion relationships and energy densities of the wave modes propagating in the PEM plate are studied;the sub-wavelength assumption is verified for the simulations in this paper. The coincidence frequency of the PEM plate is researched, and results show that the coincidence frequency of the PEM plate will disappear at certain circum-stances;mathematical and physical explanations are made for this phenomenon. The disappearance of the coincidence frequency is used to optimize the value of inductance, for the purpose of improv-ing the sound transmission loss of the PEM plate.     

微流量测量方法及其技术的发展

归纳了近五年来基于MEMS技术的微流量传感器结构及性能参数。根据国际上热门的研究方法推断微流量测量技术可能的发展方向与研究趋势,即集成两种或两种以上的测量方法,实现优势互补,提高测量精度或扩大量程比。最后基于现有的技术基础,提出了融合科氏效应与差压效应的微流量测量方法,阐述了传感器的工作原理与理论基础,并对其可行性进行了分析与论证。     

回流燃烧室流动特性试验

为了揭示有/无燃烧状态下燃烧室热态和冷态流场的特征和流动特性，针对某型回流燃烧室单头部试验件，使用粒子图像测速仪（PIV），测量燃烧室燃烧状态下不同截面处的热态流场，以及没有燃烧状态下不同截面处的冷态流场，探讨不同总压损失系数对回流燃烧室热态/冷态流场特征及流动特性的影响。研究表明:随着总压损失系数的增大，冷态条件下各截面流场结构基本保持不变，如射流孔穿透深度、射流角度、回流区位置及大小、流线等基本保持一致，但是各位置点速度大小逐渐增大。热态条件下各截面流场随着总压损失系数增大，流场结构也基本保持不变；相同总压损失系数时，热态流场与冷态流场存在差异，燃油喷射与气流的相对运动将会对燃烧室头部的流场结构造成影响，速度较冷态流动时略微增大。      

Experimental study on plasma jet deflection and energy extraction with MHD control

This paper presents an integrated research scheme for vector deflection and energy extraction in a gas plasma jet under Magneto-Hydrodynamic (MHD) control. A MHD-controlled thrust-vector test rig was used to conduct the experimental research. A gas plasma was obtained by injecting ionization seeds of Cs₂CO₃ into the combustion chamber via artificially forced ionization. The effects of the gas temperature and ionization seed mass fraction on the plasma jet deflection and energy extraction were experimentally verified under an applied magnetic field. The experimental results were analyzed theoretically. The results showed that the deflection amplitude of the gas plasma jet and the extracted voltage signal intensity increased with increasing gas temperature and the ionization seed mass fraction. The extracted dynamic voltage signals proved that the ionization seeds of Cs₂CO₃ induced gas ionization at 1173 K. The experiment verified that it is feasible to simultaneously achieve jet deflection and extract energy under the action of an external magnetic field.