基于EM‑EKF的深空光学自主导航系统光轴偏差补偿算法

在深空探测任务中,光学自主导航的精度受导航敏感器件安装精度的影响较大。提出了一种基于期望最大化-扩展卡尔曼滤波(EM-EKF)的光学自主导航系统光轴偏差补偿算法。算法基于条件概率的思想,预先设定状态变量和观测量的统计特性参数,通过不断地最大化条件期望,得到出现概率最大的状态变量估值和光轴偏差参数估值。该算法可分为4步:EKF、固定区间平滑、求解条件期望和期望最大化,不断迭代即可得到光轴偏差估计值。以火星探测近火段为例进行仿真验证,经光轴偏差补偿后,导航精度由100 km提升至20 km以内。     

神经网络模型在压气机通流特性分析中的应用

为了解决通流特性分析程序中原始模型对压气机性能预测精度不足的问题,提高压气机通流特性分析过程的可靠性,基于对大量多圆弧叶栅的数值模拟结果建立了压气机叶栅性能数据库,并以该数据库为依托,采用神经网络建模方法建立了压气机叶栅基准损失系数和基准落后角模型。结果显示:两模型对叶栅基准损失系数和基准落后角的预测精度均满足工程应用要求,其精度分别为±0.002和±1°。在对采用神经网络模型的通流特性分析程序校验过程中发现,其无论对压气机整机性能还是对流动细节的预测精度上都获得了显著提高,尤其是在主流区。此外从压气机整体特性上看,基准损失系数和基准落后角精度的提高对非设计工况损失系数和落后角的预测精度影响是积极的。      

数据收集系统下行频偏校准与点频值计算

风云二号（ＦＹ－２）卫星在轨运行期间本振源必定产生一定的频率偏移,这就影响了数据收集平台接收系统（ＤＣＰＲ）相应于各种平台的报文锁相环路的频率捕获范围,严重时将无法解调出各种平台收集的气象数据,整个系统也将无法正常工作。为解决上述问题,介绍了ＤＣＰＲ下行频偏校准及点频值计算的方法。通过ＦＹ－２卫星在轨测试表明,在随机干扰比较严重的情况下,ＤＣＰＲ对各种平台报文接收解调的成功率优于９８％,取得了令人满意的结果。     

Dependence on forming parameters of an integral panel during the electromagnetic incremental forming process

Nowadays, more and more attentions are paid to electromagnetic incremental forming(EMIF), especially for a part with a large-scale size, e.g., an integral panel with stiffened ribs. In this work, the bending of a panel into a double-curvature profile via EMIF is carried out experimentally and evaluated by comparing the formed profile with the desired profile. During the process,discharges at four positions along different discharge paths are designed. The effects of forming parameters on the die-fittingness of the workpiece are discussed, for which two evaluation indices are used to judge forming results. The results show that a discharge voltage in an incremental mode is helpful to improve the fittingness and avoid the collision rebound against the die at the same time.Discharging at the diagonal positions with the ‘‘X" discharge path exhibits the minimal shape deviation and the best forming uniformity. On the contrary, discharging at the parallel positions with the ‘‘Z" discharge path obtains the worst forming quality. Overlap of the coil at different positions should be given during EMIF; however, a lower overlap rate of the coil helps improve the forming quality. The results obtained in this work are useful for forming integral panels with stiffened ribs via the EMIF process.     

航空齿轮磨削加工安装偏心误差补偿研究

磨齿加工时齿坯几何中心与回转工作台轴心存在安装偏心误差,降低了磨齿加工精度。以数控成型砂轮磨齿机工作原理为基础,建立偏心误差磨削加工几何模型;提出安装偏心误差补偿法,建立偏心误差补偿数学模型,通过数学模型求出磨削砂轮在X、Y两个方向的进给补偿增量;以YK73125数控成型砂轮磨齿机为例,进行安装偏心误差补偿实验,齿轮的左右齿面单个齿距极限偏差绝对值分别减小了0.9μm和1.6μm,齿距累积总偏差绝对值分别减小了49.6μm和43.3μm。结果表明:安装偏心误差与单个齿距偏差和齿距累积总偏差成正比;采用安装偏心误差补偿进行磨齿加工,有效地减小了单个齿距偏差和齿距累积总偏差,齿轮的精度有所提高。     

An ethical duty: Let astronautical development unfold – to make the people more secure

In examining alternative space-development models, one observes that Heinlein postulated the first Moon flight as the outcome of the focused action of an individual – building upon an ample commercial aerospace transportation infrastructure. The same technological basis and entrepreneurial drive would then sustain a fast human and economic expansion on three new planets. Instead, historically, humans reached the Moon thanks to a “Faustian bargain” between astronautical developers and governments. This approach brought the early Apollo triumphs, but it also created the presumption of this method as the sole one for enabling space development. Eventually, the application of this paradigm caused the decline of the astronautical endeavor. Thus, just as conventional methods became unable to sustain the astronautical endeavor, space development appeared as vital, e.g., to satisfy the people?s basic needs (metabolic resources, energy, materials, and space), as shown elsewhere. Such an endeavor must grow from actions generating new wealth through commercial activities to become self-supporting. Acquisition and distribution of multiform space resources call, however, for a sound ethical environment, as predatory governments can easily forfeit those resources.     

涡轴发动机高空台模拟偏差影响的性能修正方法

针对涡轴发动机高空台试验因模拟偏差带来的性能差异问题,通过某涡轴发动机数值仿真计算和试验研究,提出了用相似换算和小偏差分析相结合的试验性能修正方法.研究结果表明:发动机输出功率和耗油率的差异从只采用相似换算时的3.0%左右下降到1.0%左右,模拟偏差对性能的影响采用此修正方法是合理可行的.      

结构形式及成型方案对飞机复材结构的外形精度影响分析

与金属相比复合材料板件的厚度偏差较大,这一弱点对保证飞机装配精度非常不利。本文针对三种典型结构形式,计算了各结构形式采用不同成型方案的外形偏差值,通过对比分析,从保证飞机外形面精度的角度提出了应选择的成型方案。     

X-Cor 夹层结构的平压性能试验

通过对不同的z-pin角度、面板厚度、去除泡沫处理的X-Cor夹层结构试样进行平压性能试验和分析比较,得到其破坏模式及不同设计参数对性能的影响。试验结果表明:X-Cor夹层结构中z-pin和泡沫存在协同增强效应;增大z-pin端部约束和减少z-pin的植入角度能提高平压性能;但z-pin角度为0°的夹层结构平压性能对植入角的角偏差缺陷更敏感,缺陷的存在影响承力性能。     

金属材料日历寿命确定的分散系数和取值

研究了在日历寿命确定中的分散性问题,通过对金属腐蚀试验数据分布规律的研究,选定了符合这种规律的分散系数计算模型;通过这些腐蚀试验数据,计算出已试验材料的标准差;通过给出的标准差计算出腐蚀试验用的分散系数的取值。