TA15钛合金薄板等离子弧对接焊缝疲劳特性研究

为了探索钛合金等离子弧焊接头的疲劳性能,本文依据TA15标准试件和轧制板材试件疲劳试验数据处理结果,采用当量应力集中系数法,在TA15薄板等离子弧焊和对接焊缝磨削组合工艺试件的疲劳试验基础上,确定了中值当量应力集中系数和安全当量应力集中系数,最后建立了该TA15薄板的S-N曲线,给出了应用结论。     

C-SiC陶瓷基复合材料磨削参数优化研究

通过C-SiC陶瓷基复合材料的正交磨削试验进行磨削参数优化研究,探讨磨削参数对内锥体表面粗糙度的影响规律,提出了磨削参数的优化原则,获得了优化的磨削参数,提高了陶瓷基复合材料内锥体精密磨削的表面加工质量。     

磨粒建模方法与切削过程仿真研究

针对砂轮表面上磨粒形状不规则、尺寸不确定的几何特征,研究了模拟实际磨粒的几何建模方法。采用随机空间平面切分正六面体的方法构建了具有实际磨粒几何特征的不规则多面体结构磨粒。基于LS-DYNA软件,采用流固耦合有限元法模拟了不规则多面体结构磨粒的切削过程。分析切削过程中工件材料的应力分布规律与切削变形规律,得出结论:工件材料的加工应力主要集中在与磨粒切削刃及棱角接触的区域;切屑沿磨粒挤压前面向上流动,并于挤压面法向方向上流出;磨粒挤压前角的增大有利于切屑的形成。利用陶瓷立方氮化硼(CBN)砂块进行了磨粒划擦试验,试验结果证实了磨粒切削仿真结果的准确性。     

环形热管砂轮强化磨削弧区换热研究

磨削过程中,在超过临界值的高磨削热流密度下,即使有再多的磨削液进入弧区也无济于事,因为磨削液既已处于成膜沸腾状态,由于工件表面所覆盖的汽膜层的阻挡,磨削液很难真正起到换热作用,如不及时采取相应的措施,工件必定很快发生烧伤。本文结合热工领域的换热技术,提出一种基于热管技术强化磨削弧区换热的全新构想,并在此基础上研制了新型的环型热管砂轮,以大幅提高弧区临界热流密度。最后,分别使用环形热管砂轮和普通砂轮进行磨削测温试验,验证了环形热管砂轮高速疏导磨削热,降低磨削温度,从而提高材料去除率的巨大潜力。     

Investigation on induction brazing of profiled cBN wheel for grinding of Ti-6Al-4V

Profiled monolayer cBN wheel was induction brazed for grinding of titanium dovetail slot in this study. Aimed at acquiring a uniform temperature distribution along the profiled surface and reducing the thermal deformation of the brazed wheel, a finite element model was established to investigate the temperature uniformity during induction brazing. A suitable induction coil and the related working parameters were designed and chosen based on the simulation results. Ag-Cu-Ti alloy and cBN grains were applied in the induction brazing experiment. The results showed geometric deformation of the brazed wheel was no more than 0.01 mm and chemical reaction layer were found on the brazed joint interface. Further validation tests were carried out by grinding of Ti-6Al-4V alloy. Compared to the electroplated wheel, the brazed wheel showed better performance such as low specific grinding energy and good ground quality in grinding of Ti-6Al-4V alloy. Abrasion wear was found to be the main failure mode for the induction brazed wheel, while adhesion and grains pull-out were the main failure mode for the electroplated wheel.     

Effect of creep feed grinding on surface integrity and fatigue life of Ni3Al based superalloy IC10

Ni₃Al-based superalloy IC10 is widely used in high temperature components of aero-engines because of its superior mechanical properties. In this paper, the creep feed grinding properties of IC10 were investigated experimentally. The effects of grinding parameters on the grinding forces and temperature were examined. Moreover, the influences of surface roughness and hardening on the high-cycle fatigue life of IC10 specimens were studied. To control the creep feed grinding parameters and enhance the fatigue life of IC10 components, the experimental results were summarized to offer a useful reference point. It is concluded that, the grinding depth is the most important factor which influencing the grinding forces and temperature; the surface roughness is the main and unfavorable factor on the fatigue life of IC10, while the surface hardening has a positive influence on the fatigue life; to obtain a better surface quality and improve the fatigue life of IC 10, the recommended grinding parameter domain involves wheel speed ∈ [15, 20] m/s, feed rate ∈ [150, 200] mm/min, and grinding depth ∈ [0.4, 0.5] mm.     

面向型面精度一致性的整体叶盘砂带磨削新方法及实验研究

由于整体叶盘由多个叶片组成,根据"木桶定律",整体叶盘的性能和寿命取决于型面精度(型线精度和表面质量)最差的叶片。因此,在满足整体叶盘型面精度的前提下,提高各叶片型面精度一致性对其性能和寿命具有重要的影响。提出一种面向型面精度一致性的砂带磨削新方法,一方面通过砂带周期性的往复运动结合自锐式磨削原理,实现型面铣削残差层的高效去除;另一方面通过砂带周期性的自动更新,保证各叶片的型面精度在同一截面具有高一致性。阐述并建立了面向型面精度一致性的砂带磨削新方法及其磨削控制方程。在此基础上,对某航空发动机整体叶盘的11个叶片进行了砂带磨削实验,并且运用标准差对整体叶盘型面精度一致性进行定量分析。研究结果表明:整体叶盘磨削后,表面粗糙度小于0.25 μm,型线精度小于0.05 mm,同时型面精度一致性显著提高,证明了该方法的有效性。     

Interference and grinding characteristics in ultra-precision grinding of thin-walled complex structural component using a ball-end grinding wheel

As for ultra-precision grinding of difficult-to-process thin-walled complex components with ball-end grinding wheels, interference is easy to occur. According to screw theory and grinding kinematics, a mathematical model is established to investigate the interference and grinding characteristics of the ball-end wheel. The relationship between grinding wheel inclination angle, C axis rotation angle, grinding position angle and grinding wheel wear are analyzed. As the grinding wheel inclination angle increases, the C axis rotatable range decreases and the grinding position angle increases. The grinding position angle and wheel radius wear show a negative correlation with the C axis rotation angle. Therefore, a trajectory planning criteria for increasing grinding speed as much as possible under the premise of avoiding interference is proposed to design the grinding trajectory. Then grinding point distribution on the ball-end wheel is calculated, and the grinding characteristics, grinding speed and maximum undeformed chip thickness, are investigated. Finally, a complex structural component can be ground without interference, and surface roughness and profile accuracy are improved to 40.2 nm and 0.399 μm, compared with 556 nm and 3.427 μm before ultra-precision grinding. The mathematical model can provide theoretical guidance for the analysis of interference and grinding characteristics in complex components grinding to improve its grinding quality.     

渐开线碟形砂轮磨削面齿轮数控加工研究

为进行面齿轮数控精密加工,提出了一种渐开线碟形砂轮磨削面齿轮加工方法.根据面齿轮成形过程及磨削加工原理,推导了渐开线碟形砂轮磨削面齿轮齿面方程,进行了面齿轮磨削加工机床设计,给出了基于机床结构的面齿轮磨削加工方法,进行了磨削加工过程中的啮合点刀位计算;借助VERICUT软件进行了面齿轮数控磨削加工仿真,最后进行了面齿轮磨削加工试验,通过对面齿轮齿面进行检测,得到齿面偏差最大值为-10.1~12.1μm,结果验证了渐开线碟形砂轮磨削加工面齿轮方法的正确性.      

精密研磨加工薄壁半盲孔及高精度平板的方法

本文着重从研磨加工的手法、研磨膏的配比、不同材料的研磨磨料选用等方面进行探讨,并详细叙述各种加工方式对产品质量的影响,通过典型零件加工技术的具体阐述,将研磨加工的方法及技巧做详细的描述,利于技术交流及推广.