0.4C-铬镍钼硅钢多冲疲劳裂纹起始寿命估算

 本文采用局部应力一应变法,结合Coffin公式,忽略弹性应变。考虑应变速率的影响,导出了在给定的试验条件下,根据材料的拉伸性能估算其多冲疲劳裂纹起始寿命的表达式,经试验结果验证表明,对不同冲击能量,不同热处理状态以及不同缺口形状的多冲试样,估算式均具有较高的准确性。     

316不锈钢/WC-Co涂层在锌液中的腐蚀

研究了经高速火焰喷涂(HVOF)的316不锈钢WC-Co涂层在锌液中的腐蚀行为,包括腐蚀速度、界面组织形貌和成分的变化.结果表明,WC-Co涂层在锌液中的腐蚀表现为沿裂纹的腐蚀.涂层中的缺陷造成裂纹源,在锌液和热喷涂过程留下的残余热应力的作用下,发生裂纹扩展,形成沿裂纹的腐蚀.铬和铝的扩散能力都比锌强,在产生裂纹的初期,铬和铝将优先锌扩散到裂纹中.如果适当改善喷涂工艺,增加涂层的致密度,可以延长涂层的使用寿命.     

液体密度传感器

介绍了几种典型的液体密度传感器的基本结构、工作原理与应用特点.     

气动参数对后台阶三维缝隙换热影响的研究

针对涡轮叶片尾缘冷却结构特点,建立了后台阶三维缝隙结构气膜冷却特性试验台,测量了缝隙中心和肋中心下游换热系数的局部分布,研究了不同雷诺数Re(5000~15000)与吹风比Br(0.5~2.0)对换热系数的影响规律,试验结果表明:(1)出口的换热系数总体呈下降趋势,但在肋后中心线略有起伏;(2)随着Re的增大,换热系数增大,随着Br的增大,换热系数减小;(3)在靠近出口位置,由于热边界层与三维掺混特性流场的影响,使得换热变得复杂。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

CFRP层板的落重冲击分层损伤研究

采用落重冲击试验方法研究了航空上常用的铺层形式为［Ｏ２／９Ｏ２／４５２／－４５２］ｓ的先进复合材料（ＣＦＲＰ）低能冲击损伤问题。重点讨论了落重冲击后分层损伤形貌、冲击能量Ｗ与分层面积Ａ之间的关系以及基体韧性对ＣＦＲＰ抗冲击性能影响。     

Study on the breakup lengths of free round liquid jets

IntroductionBreakup and atomization of roundliquidjetshad been widely used in internal combustion en-gines,gas turbines,and liquid rocket engines.Recently,with the development of scramjet en-gines and the deepening of fuel atomization re-search,it attract…     

Kinetic Monte Carlo Simulation of EB-PVD Film:Effects of Substrate Temperature

The 2D kinetic Monte Carlo (KMC) simulation was used to study the effects of different substrate temperatures on the microstruc-ture of Ni-Cr films in the process of deposition by the electron beam physical vapor deposition (EB-PVD). In the KMC model, substrate was assumed to be a “surface” of tight-packed rows, and the simulation includes two phenomena: adatom-surface collision and adatom diffusion. While the interaction between atoms was described by the embedded atom method, the jumping energy was calculated by the molecular static (MS) calculation. The initial location of the adatom was defined by the Momentum Scheme. The results reveal that there exists a critical substrate temperature which means that the lowest packing density and the highest surface roughness structure will be achieved when the temperature is lower than the smaller critical value, while the roughness of both surfaces and the void contents keep decreasing with the substrate temperature increasing until it reaches the higher critical value. The results also indicate that the critical substrate temperature rises as the deposition rate increases.     

低速轴流压气机尾流撞击效应的数值模拟

利用二维数值模拟研究了低速轴流压气机上游尾迹对下游相邻叶排的非定常分离流场的影响。研究表明：满足一定通过频率和亏损幅值条件的尾迹能够有效抑制下游相邻叶排尾缘涡的生成，达到控制或是推迟附面层非定常分离的目的，从而使得流场时均性能大幅度的提高，损失系数降低了40．2％，功损比增加93％。为固有非定常潜能的利用提供了一类新途径。     

飞机风挡透明件的鸟撞分析

 本文研究了风挡透明件鸟撞动力响应的分析模型和方法。考虑了撞击载荷与风挡透明件动力响应的耦合作用和非线性效应。为了能方便地使用现有的非线性有限元分析程序并避免数值解的振荡现象,在研究中不采用常用的拉格朗日法和罚函数法,而是采用动量平衡法。同时,为了避免不断调整撞击接触点和修改网格,本文采用超弹性的橡皮材料来模拟鸟体,而不是象国外那样采用流体柱。研究和比较了衍生动载荷响应解,并提出相应的看法。