前向数据接入方式对导航星座网络通信性能的影响分析

对采用时分多址轮询建链体制的导航星座星间链路网络，为了指导星间链路网络地面前向数据接入的应用，分析了不同地面前向数据接入方式的星-星-地联合数据交互机制及其对网络通信性能的影响，并结合应用代价给出了综合评价和使用建议。以前向数据最快路径接入方式和固定节点接入方式为代表，分析了星间链路网络与地面间星 星 地联合数据交互机制的特点，明确了两种方式下星间链路网络拓扑路由规划策略的制定原则。通过构建Walker 24/3/1导航星座星间链路网络数据处理模型及典型星地运行场景，对两种地面前向数据接入方式仿真分析了星间链路通信容量和传输时延等网络通信性能，比较分析了通信容量及数据拥塞规律，得出前向数据最快路径接入方式相比于固定节点接入方式在通信性能上有较明显优势的结论。最后，综合给出了两种星 星 地联合数据交互机制的应用性评价,同时给出了在通信容量较低且通信时延要求不高、但可靠性要求较高的应用条件下，可适度采用固定节点接入方式的建议。     

共轴刚性双旋翼/机身干扰流场数值模拟

采用滑移网格技术求解Navier-Stokes (RANS)方程的方法,研究了共轴刚性双旋翼/机身的干扰问题。通过Caradonna-Tung旋翼、Robin直升机、Maryland直升机旋翼/机身干扰和Harrington 2共轴双旋翼等算例,验证了所提出的旋翼流场数值模拟方法的正确性。在此基础上,以Maryland机身为原型,分析了不同桨距的共轴刚性双旋翼与机身之间的干扰特性。结果表明:所提出的数值模拟方法能够很好地模拟共轴刚性双旋翼/机身的气动干扰特性;由于机身对于共轴刚性双旋翼下洗流场的阻滞作用,旋翼的悬停效率增加5%左右,并且随着拉力系数的增大使得悬停效率的增量更加明显;旋翼的悬停效率增加主要来源于下旋翼0°方位角附近的桨叶升力系数的增大,并且拉力系数的增量由桨根向桨尖方向逐渐减小。      

共轴刚性旋翼气动干扰数值计算方法

建立了一个适用于共轴刚性旋翼气动特性分析的数值模拟方法。该方法采用任意拉格朗日欧拉方法(Arbitrary Lagrange Euler,ALE)描述的可压缩Navier-Stokes(N-S)方程求解流场,采用低数值耗散的Roe格式进行空间离散;使用多重嵌套网格方法以模拟双旋翼的运动。针对共轴刚性旋翼配平,引入"差量修正"策略解决了传统配平中雅克比矩阵计算复杂的问题。首先,对Harrington-2共轴双旋翼的悬停气动性能进行了计算,然后,对某2 m直径共轴双旋翼的悬停及前飞状态进行了计算,并与试验值进行了对比。结果表明:在典型状态下拉力系数的计算结果与试验值误差在3%以内,扭矩系数的计算结果与试验值误差基本在5%以内;所采用的数值计算方法对旋翼涡尾迹特征具有较高的捕捉精度,可以有效模拟共轴刚性旋翼悬停和小速度前飞下的复杂流场及其细节特征。     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.     

Aerodynamics of smart flap under ground effect

Aerodynamic characteristics of two-dimensional smart flap under the ground effect have been assessed by a numerical simulation. In this process, a pressure-based implicit procedure to solve Navier–Stokes equations on a nonorthogonal mesh with collocated finite volume formulation is used. The boundedness criteria for this procedure are determined from the Normalized Variable Diagram (NVD) scheme. The procedure incorporates the k–ε eddy–viscosity turbulence model. Cantilever beam with uniformly varying load with roller support at the free end is considered for the configuration of the smart flap. The method is first validated against experimental data. Then, the algorithm is applied for turbulent aerodynamic flows around airfoil with smart and conventional flaps for different attack angle, flap angle and ground clearance where the results of two flaps are compared. The comparisons show that the quality of the solution is considerable.     

含激波的湍流流动高精度大涡数值模拟方法

针对采用亚格子模型进行含激波的湍流流动模拟时会面临激波附近的精度损失问题,考虑从通过亚格子模型以及数值模拟方法两方面的改进来实现湍流流动大涡模拟的精度提高.大涡模拟采用了Yee及Sj(o)green (2009)提出的高阶低耗散方法.该方法采用自适应的流场探测器以控制计算中所需区域的数值耗散,并考虑对动力学模型采用在激波位置使用Sagaut和Germano(2005)提出的单边亚格子过滤器和(或)直接禁用亚格子项等方法加以改进.对于标准的马赫数1.5和3条件下的激波-湍流干扰问题,上述新方法相较于全区域采用亚格子模型的方法均表现出了相似的精度提升.同时实现的数值精度改进方案采用了Harten的亚单元分辨过程来定位和锐化激波,并在精确激波位置附近的网格点处采用了单边测试滤波.     

蜂窝式轴心通风器油气分离性能计算

为对航空发动机蜂窝式轴心通风器油气分离效率进行研究,建立考虑油气双向耦合的流场计算方法及油滴/壁面相互作用模型,在验证通风阻力及油气分离效率可靠性的基础上,对不同转速、通风流量和环境温度下蜂窝式轴心通风器的油气分离效果进行计算和分析.结果表明:转速的增加会使油气分离效率得到提升,而通风流量和环境温度的增加则导致油气分离效率的降低.蜂窝孔结构的加入对通风阻力影响不大,却对通风器的滑油分离过程起主要作用,计算表明其对滑油分离贡献率在80%以上.      

Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

Parachute dynamics and perturbation analysis of precision airdrop system

To analyze the parachute dynamics and stability characteristics of precision airdrop system,the fluid–structure interaction(FSI) dynamics coupling with the flight trajectory of a parachute–payload system is comprehensively predicted by numerical methods.The inflation behavior of a disk-gap-band parachute is specifically investigated using the arbitrary Lagrangian–Euler(ALE) penalty coupling method.With the available aerodynamic data obtained from the FSI simulation,a nine-degree-of-freedom(9DOF) dynamic model of a parachute–payload system is built and solved to simulate the descent trajectory of the multi-body dynamic system.Finally,a linear five-degree-of-freedom(5DOF) dynamic model is developed,the perturbation characteristics and the motion laws of the parachute and payload under a wind gust are analyzed by the linearization method and verified by a comparison with flight test data.The results of airdrop test demonstrate that our method can be further applied to the guidance and control of precision airdrop systems.     

Design and implementation of rigid-flexible coupling for a half-flexible single jack nozzle

The aerodynamic design of a rigid-flexible coupling profile is the decisive factor for the flow-field quality of a supersonic free jet wind tunnel nozzle, and its mechanic dynamic features are the key for engineering implementation of continuous Mach number regulations. To fulfill the requirements of a free jet inlet/engine compatibility test within a wide simulation envelop, both uni-form flow-fields of continuous acceleration and deceleration are necessary. In this paper, the aero-dynamic design methods of an expansion wall and machinery implementation plan for the half-flexible single jack nozzle were researched. The profile control in nozzle flexible plate design was studied with a rigid-flexible coupling method. Design and calculations were performed with the help of numerical simulation. The technique of axial free stretching of the flexible plate was used to improve the matching performance between the designed elasticity profile and the theoretical one, and the rigid-flexible coupling structure was calibrated by wind tunnel tests. Results indicate that the flexible plate aerodynamic design method used here is effective and feasible. Via rigid-flexible coupling design, the flexible plate agrees with the rigid body very well, and continuous Mach number changes can be achieved during the tests. The nozzle’s exit flow-field uniformity meets the requirements of China Military Standard (GJB).