飞航导弹/涡扇发动机一体化设计-约束分析与任务分析

1引言与火箭发动机相比,涡喷、涡扇发动机在亚声速条件下具有更高的比冲,而且发动机的状态可以调节,因而推力可以改变,所以以涡喷、涡扇发动机为主动力的飞航导弹具有更远的射程,并能够实现更为复杂的飞行弹道。另一方面,由于涡喷、涡扇发动机的特性参数(推力和耗油率)会随飞行     

某型发动机对畸变进气响应的流动耦合分析

建立了畸变进气下某型双轴发动机高压压气机，扩压器间流动耦合模型，完善了畸变进气对发动机稳定性影响模拟方法。数值模拟结果表明，考虑耦合影响给出的高压压气机出口静压畸变与其总压畸变不仅相位相反，而且随进口总压畸变强度变化而变化。据此所给出的高、低压压气机畸变响应和发动机推力响应特性也与进气道，发动机相容性理论相符合。     

低Re数管内强化对流传热实验研究

分别应用螺旋线圈和扭带作为插入物，在Ｒｅ≤２．０×１０３下，研究管内水与管壁的传热强化，与光管传热作了比较分析。并归纳出强化传热Ｎｕ数及流动阻力系数ζ随Ｒｅ的变化规律，反映出螺旋线圈和扭带在低Ｒｅ下有不同程度的强化传热效果，但也相应地增加了流动阻力。文中对两种强化传热元件也作了相应的比较。     

数值模拟方法对NASA CRM模型阻力预测的影响

在复杂工程外形的数值模拟中，网格类型、规模和分布、湍流模型、数值格式等都会不同程度影响模拟结果。如何评估这些模拟方法对模拟结果的影响，并识别对模拟结果影响较显著的因素，对于CFD的发展方向有积极的借鉴指导意义。为了综合研究不同因素对商用运输机外形阻力预测的影响，以AIAA第六届阻力预测会议外形NASA CRM为研究对象，同时考虑了网格、湍流模型、无黏通量格式和体心梯度求解方法等因素对阻力预测的影响。分析中采用枚举法和正交试验设计两种方法，并使用了基于聚类分析的定性敏感性分析方法和基于Mckay主影响分析的定量方法，识别出对阻力预测影响较大的因素，这为数值模拟方法的发展指明了方向。     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

火星大气进入段抗饱和固定时间阻力加速度跟踪制导律设计

研究了具有固定时间收敛特性的火星探测器大气进入段的标称轨迹跟踪制导问题。首先，针对横向运动，给出与速度成线性关系的航向误差漏斗走廊形式，完成了倾侧角的反号逻辑设计。与横程漏斗走廊反号逻辑相比，该逻辑计算量小，更适用于宇航计算机。与航向误差宽度走廊反号逻辑相比，该逻辑在高速状态下能够避免倾侧角的频繁切换，可提高任务成功的概率。其次，针对纵向运动，通过RBF神经网络补偿了倾侧角饱和问题，利用积分滑模设计了阻力加速度固定时间饱和跟踪制导律，其不仅可有效消除滑模控制的抖振问题，且将跟踪误差以两种不同形式引入制导律，能够加速收敛，能够保证跟踪误差在固定时间内快速收敛至0。最后，通过数值仿真验证了所设计的横向倾侧角切换逻辑和纵向制导律对标称轨迹的快速、精确跟踪能力。     

某型飞机阻力伞抛放系统故障模式分析

针对某型飞机阻力伞系统放伞、抛伞故障,通过分析系统的组成、工作原理、常见故障模式以及故障原因,提出了改进建议,为该型飞机阻力伞抛放系统故障的排除提供思路。     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.     

Laminar flow control research at TsAGI: Past and present

This paper presents a brief review of activities in laminar flow control being performed at the Central Aerohydrodynamic Institute named after Prof. N.E. Zhukovsky (TsAGI). These efforts are focused on the improvement of the existing laminar flow control methods and on the development of new ones. The investigations have demonstrated the effectiveness of aircraft surface laminarization applications with the aim of friction drag reduction. The opportunity of considerable delaying of laminar-turbulent transition due to special wing profile geometry and using boundary layer suction and surface cooling has been verified at sub- and supersonic speeds through various wind tunnel testing at TsAGI and during flying laboratory experiments at the Flight Research Institute (LII). The investigations on using hybrid laminar flow control systems for friction drag reduction were also carried out. New techniques of laminar flow control were proposed, in particular, the method of local heating of the wing leading edge, boundary layer laminarization by means of receptivity control, and electrohydrodynamic methods of boundary layer stability control.     

Aerodynamics of smart flap under ground effect

Aerodynamic characteristics of two-dimensional smart flap under the ground effect have been assessed by a numerical simulation. In this process, a pressure-based implicit procedure to solve Navier–Stokes equations on a nonorthogonal mesh with collocated finite volume formulation is used. The boundedness criteria for this procedure are determined from the Normalized Variable Diagram (NVD) scheme. The procedure incorporates the k–ε eddy–viscosity turbulence model. Cantilever beam with uniformly varying load with roller support at the free end is considered for the configuration of the smart flap. The method is first validated against experimental data. Then, the algorithm is applied for turbulent aerodynamic flows around airfoil with smart and conventional flaps for different attack angle, flap angle and ground clearance where the results of two flaps are compared. The comparisons show that the quality of the solution is considerable.