橇式起落架动刚度及阻尼特性试验研究

起落架动刚度及阻尼特性是研究直升机“地面共振”问题两个重要参数。刚进入国产化阶段的模式起落架迄今尚无可靠的理论计算方法来确定这两个参数．本试验研究利用某型直升机真实的模式起落架为试件，采用机械阻抗测量法来研究该起落架的动刚度及阻尼特性。试验使用电液伺服激振设备，对模式起落架进行不同频率的激振，实时测量相应的载荷及位移响应，从而得出了模式起落架的动刚度及阻尼。试验模拟了直升机完全停机及半升力卸载情况，在机场及冰面降落情况，以及３个不同方向的受载情况。试验结果已直接用于某型直升机的“地面共振”分析。     

考虑高载和阻尼介质时刚塑性圆板的塑性动力分析

本文研究了阻尼介质对刚塑性圆板在高载(冲击荷载)作用下塑性动力响应的影响,得到了解析解并对此解进行了讨论。当阻尼介质参数趋于零时,本文结果与无阻尼解一致。文中还画出了荷载与阻尼介质对圆板运动时间和板中心点残余挠度的影响曲线。     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

基于改进准则法的复合壳阻尼结构拓扑减振动力学优化

针对复合壳阻尼结构的拓扑减振优化问题，以约束阻尼层的有限单元为设计变量，采用体积比、模态频率和振型为优化约束条件，构建以多模态权重系数的结构模态损耗因子数值关系为优化目标函数的拓扑减振优化模型。为了拓展优化目标灵敏度具有不局限于某一变密度法插值模型的形式，推导了数值表达式的一般函数式。动力学优化中优化目标灵敏度正、负数集共存，使得非凸性的目标函数设计变量出现负值或优化函数寻优于局部极值点。为此，推导出复合壳阻尼结构的全域灵敏度改进优化准则法迭代格，以确保每次迭代域均为全域设计变量集。结合有限单元法编程实现了复合壳阻尼结构改进准则法，并对复合壳结构进行拓扑减振优化分析。结果表明：在敷设体积减为全覆盖的50%时，复合壳结构的模态损耗因子增减偏差为10%，具有提升减振的轻量化设计目的；各阶目标函数和拓扑构型所需的迭代次数少，中间密度区域较小，多阶优于单阶模态优化函数，易于获得全域寻优的有效减振。     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.     

Aerodynamics of smart flap under ground effect

Aerodynamic characteristics of two-dimensional smart flap under the ground effect have been assessed by a numerical simulation. In this process, a pressure-based implicit procedure to solve Navier–Stokes equations on a nonorthogonal mesh with collocated finite volume formulation is used. The boundedness criteria for this procedure are determined from the Normalized Variable Diagram (NVD) scheme. The procedure incorporates the k–ε eddy–viscosity turbulence model. Cantilever beam with uniformly varying load with roller support at the free end is considered for the configuration of the smart flap. The method is first validated against experimental data. Then, the algorithm is applied for turbulent aerodynamic flows around airfoil with smart and conventional flaps for different attack angle, flap angle and ground clearance where the results of two flaps are compared. The comparisons show that the quality of the solution is considerable.     

大阻尼高刚度复合材料仪表板的设计结构与工艺研究

设计了一种五层夹芯多层阻尼薄膜嵌入的复合材料仪表板结构,并采用多次热压罐固化成型工艺来制作该大阻尼高刚度复合材料仪表板.它们分别是:上、下蒙皮和中心层的制作,上、下蒙皮和中心层与泡沫塑料的粘接与紧固件的预埋,孔的修正及仪表板的包边加工.通过成形质量检验和加载试验,验证了成形工艺的可行性和合理性.     

上下游干涉对转子叶片颤振特性的影响

使用自行开发的非定常流动数值模拟程序,分别考虑上、下游叶排干涉作用对转子叶片的颤振特性进行了研究,分析尾迹和势干扰对气动阻尼的影响规律.对转子叶片表面非定常压力进行傅里叶变换,使用能量法计算气动阻尼,研究不同叶片排轴向间距下气动阻尼的变化.通过考虑转静干涉效应的气动阻尼与单转子结果对比,总结了干涉作用对叶片颤振特性的影响规律;结果表明:上游导叶与转子一倍弦长间距时,获得正气动阻尼,与单转子预测的气动弹性稳定性结果相反.说明在进行颤振特性预测时必须考虑转静干涉作用;尾迹和势干扰的强度均随着轴向间距值的减小而加强,且都会加剧叶片气动弹性失稳.      

翼吊发动机安装结构等效建模及其隔振设计

为了研究翼吊发动机安装结构隔振特性并优化其隔振器设计,建立了发动机安装节-吊架-机翼结构理论分析及有限元模型.利用有限元方法进行了模态验证并分析了安装结构的隔振特性.进行发动机3种典型工况下的结构动响应分析确定了振动传递的主路径.基于振动传递路径法研究了隔振器参数和安装位置对安装系统隔振性能的影响规律.结果表明:振动载荷经安装结构后低压转子转频和高压转子转频峰值响应分别降低22.03%和14.65%.低压转子转频振动传递主路径为发动机-前安装节-吊架-机翼,高压转子转频为发动机-后安装节-上连杆-机翼.通过合理设置隔振器位置可以使安装系统隔振率达到50.41%,隔振器的频率比为5和阻尼比为0.25时安装系统隔振率可达70.67%.为了优化整个发动机安装系统的隔振效果,设计隔振器时必须选取合适的安装位置和参数.      

Design and implementation of rigid-flexible coupling for a half-flexible single jack nozzle

The aerodynamic design of a rigid-flexible coupling profile is the decisive factor for the flow-field quality of a supersonic free jet wind tunnel nozzle, and its mechanic dynamic features are the key for engineering implementation of continuous Mach number regulations. To fulfill the requirements of a free jet inlet/engine compatibility test within a wide simulation envelop, both uni-form flow-fields of continuous acceleration and deceleration are necessary. In this paper, the aero-dynamic design methods of an expansion wall and machinery implementation plan for the half-flexible single jack nozzle were researched. The profile control in nozzle flexible plate design was studied with a rigid-flexible coupling method. Design and calculations were performed with the help of numerical simulation. The technique of axial free stretching of the flexible plate was used to improve the matching performance between the designed elasticity profile and the theoretical one, and the rigid-flexible coupling structure was calibrated by wind tunnel tests. Results indicate that the flexible plate aerodynamic design method used here is effective and feasible. Via rigid-flexible coupling design, the flexible plate agrees with the rigid body very well, and continuous Mach number changes can be achieved during the tests. The nozzle’s exit flow-field uniformity meets the requirements of China Military Standard (GJB).