热变形参数对镁合金力学性能及微观组织的影响

基于热模拟机GLEEBLE1500,以AZ31为研究对象进行热压缩实验,获得材料的应力-应变曲线。用金相显微镜对不同温度及应变速率下的金相进行观察分析,并对比分析热压缩前后的微观组织。同时分析了不同温度及应变速率下材料的力学行为,其行为属于典型的动态再结晶型。当热压缩温度为350℃和400℃时,材料强度随应变速率增大而增大,且加工硬化也增大。当应变速率为0.01和0.1/s时,随着变形温度的升高,材料的应力逐渐降低。在不同温度下,应变速率为0.01/s时的应力比应变速率为0.1/s时的应力要低。     

Fronts and thermohaline structure of the Brazil–Malvinas Confluence System

Fronts and thermohaline structure of the Brazil–Malvinas Confluence System (BMCS) are studied from climatic data, “Marathon Exp. Leg.8, 1984” data, and Sea surface temperature (SST) data base “ds277-Reynolds” (1981–2000). The South Atlantic Central Water (SACW) is divided in two main types: tropical (TW) and subtropical water (ST). Water masses, Fronts, Inter-Frontal and Frontal Zones are analysed and classified: (a) the water masses: Tropical Low-Salinity Water, Tropical Surface Water, Tropical Tropospheric Water, Subtropical Low-Salinity Water, Subtropical Surface Water, Subtropical Tropospheric Water. T,S characteristics of intermediate, deep and bottom water defined by different authors are confirmed and completed; (b) the Inter-Frontal Zones: Tropical/Brazil Current Zone, Subtropical Zone and Subantarctic Zone; (c) the Frontal Zones: Subtropical, Subantarctic and Polar, and (d) the Fronts: Subtropical Front of the Brazil Current, Principal Subtropical Front, North Subtropical Front, Subtropical Surface Front, South Subtropical Front, Subantarctic Surface Front, Subantarctic Front and Polar Front. Several stable T–S relationships are found below the friction layer and at the Fronts. The maximum gradient of the oceanographic characteristics occurs at the Brazil Current Front, which can be any of the subtropical Fronts, depending on season. Minimum mean depth of the pycnocline coincides with the Fronts of the BMCS, indicating the paths of low-salinity shelf waters into the open ocean. In the work it is shown how to recover the horizontal and vertical thermohaline structure of waters from satellite data RSMAS SST.     

AZ91镁合金负压消失模铸造充型速度的研究

真空度、浇注温度及模样厚度对AZ91镁合金消失模铸造充型速度影响的全因子实验的结果表明 ,它们都对充型速度起积极的作用 ,真空度是决定充型速度的一个关键工艺参数。在不抽真空时 ,充型速度非常小且随充型过程的进行逐渐降低 ,浇注温度对充型速度的影响也很小 ;抽真空时 ,充型速度在充型过程中不断变化且呈现不出任何规律 ,其起伏的幅度随真空度、浇注温度和模样厚度的增大而增大 ;在真空度较低时 ,随着真空度和 或浇注温度的提高 ,平均充型速度迅速增大 ,真空度与浇注温度对充型速度的交互作用增强 ;在较高的真空度下 ,平均充型速度仍随浇注温度的提高而增大 ,但平均充型速度的增大速率却随真空度的进一步提高而降低 ,真空度与浇注温度对充型速度的交互作用很弱。模样厚度对平均充型速度影响在抽真空时有所提高。     

AZ31镁合金A-TIG焊的研究

针对AZ31镁合金，研究了在A—TIG焊中单一成分的活性剂和涂敷量对焊缝成形的影响。结果表明，与无活性剂的焊缝相比，活性剂TiO2、SiO2、Cr2O3、CdCl2和CaCl2能够有效地增加镁合金焊缝的熔深和深宽比。但涂敷有氟化物的镁合金焊缝熔深没有增加，涂敷CaF2的焊缝甚至出现开裂现象。在AZ31镁合金的焊接中，活性剂CdCl2的效果最好。     

电化学辅助沉积KH-570硅烷对AZ31B镁合金耐蚀性能的影响

采用电化学辅助沉积方法对AZ31B镁合金进行硅烷化处理,借助于动电位极化曲线和电化学阻抗谱等电化学测试手段研究了γ-(甲基丙烯酰氧基)丙基三甲氧基硅烷(KH-570)添加量对膜层质量及耐蚀性能的影响,并比较了利用羟基磷灰石(HA)颗粒、铈盐离子(Ce3+)两种改性物质改良硅烷溶液后所制得膜层的质量及耐蚀性能.结果表明:AZ31B镁合金经电化学辅助沉积硅烷处理后,表面生成一层均匀而致密的硅烷透明膜层,有效地减缓了镁合金的腐蚀行为,促使其自腐蚀电流密度大大降低;在硅烷电化学辅助沉积处理过程中,KH-570存在最佳添加量,当其添加体积约为8 mL时所制备出的硅烷膜层质量最好、耐蚀性能最佳;通过改良硅烷溶液,电化学辅助沉积制备的硅烷膜层质量进一步提高,Ce3+改良效果更佳.     

热输入对AZ31镁合金FSP试样力学性能的影响

分别利用普通钢制垫板和自制的带有冷水通道的铜制垫板,对AZ31镁合金进行了搅拌摩擦加工。利用光学显微镜(OM)、SEM、显微硬度仪和拉伸设备,研究了被加工件厚度、搅拌头焊接速率和冷却条件对试样搅拌区力学性能的影响。研究表明:试样搅拌区从上层至中层和底层,再结晶晶粒尺寸依次减小。通过减小被加工件厚度、增大搅拌头焊接速率和加快冷却速率等方法,抑制了试样搅拌区晶粒长大。在搅拌头转速和焊接速率分别为800r/min和90mm/min的条件下,得到的搅拌区底部平均晶粒尺寸约为450nm,该区域显微硬度为96HV,与普通钢制垫板制备的试样相比,硬度提高了24HV,其屈服强度、抗拉强度和伸长率分别提高为原材料的1.27倍、1.6倍和2.2倍。     

Dynamic tensile behavior of AZ31B magnesium alloy at ultra-high strain rates

The samples having {0001} parallel to extruding direction(ED) present a typical true stress–true strain curve with concave-down shape under tension at low strain rate. Ultra-rapid tensile tests were conducted at room temperature on a textured AZ31 B magnesium alloy. The dynamic tensile behavior was investigated. The results show that at ultra-high strain rates of 1.93 · 102 s 1and 1.70 · 103 s 1, the alloy behaves with a linear stress–strain response in most strain range and exhibits a brittle fracture. In this case, {10-12} 10-11 extension twinning is basic deformation mode. The brittleness is due to the macroscopic viscosity at ultra-high strain rate, for which the external critical shear stress rapidly gets high to result in a cleavage fracture before large amounts of dislocations are activated. Because {10-12} tension twinning, {10-11} compressive twinning,basal a slip, prismatic a slip and pyramidal c + a slip have different critical shear stresses(CRSS), their contributions to the degree of deformation are very differential. In addition,Schmid factor plays an important role in the activity of various deformation modes and it is the key factor for the samples with different strain rates exhibit various mechanical behavior under dynamic tensile loading.     

AZ91D镁合金低压交流氧化成膜机制

基于一种低的交流电压条件(10 V),在NaOH和Na₂SiO₃的混合溶液体系中,对AZ91D镁合金进行电化学阳极氧化处理.利用扫描电镜(SEM)、X射线能谱仪(EDS)、X射线衍射仪(XRD)、电化学测试技术等手段研究了AZ91D镁合金表面阳极氧化的成膜过程、膜层生长的特点以及氧化工艺参数对膜层性能的影响规律.试验结果表明:在10 V这样低的交流电压下,在镁合金表面获得的氧化膜层表面均匀,为无孔洞的平层状膜层,其生长过程呈叠加式特点;获得的氧化膜层的主要成分为Mg₂SiO₄;在质量分数为3.5%的NaCl溶液中,经过电化学阳极氧化的镁合金的耐蚀性优于未经处理的镁合金.      

X—31A飞机的设计特点和试飞情况

综述了为验证增强战斗机机动性(EFM)计划、衡量过失速机动飞行的可行性及其在近距空战中的战术价值,X-31A飞机在气动布局、大迎角抗偏离设施、推力矢量系统以及飞控系统方面的特点;介绍了X-31A飞机的有关飞行试验情况,特别是循序渐近的四种过失速机动动作以及空战效能评估结果。结果表明,X-31A飞机气动布局合理,能完成过失速机动飞行。且过失速机动技术和推力矢量组合,可以大大地提高飞机近距空战的作战效能。     

Generation of secondary waves due to intensive large-scale AGW traveling

By using data from GPS receivers we detected huge-amplitude solitary large-scale traveling acoustic-gravity waves (LS AGW) which manifested themselves as perturbations of total electron content (TEC) of duration of about 40 min. Originated in the auroral area after significant alterations of geomagnetic field intensity during geomagnetic storms on 29–30 October 2003, LS disturbances propagated with a velocity about 1000–1200 m/s and caused generation of secondary small-scale (SS) waves with time period of 2–10 min. Such SS structure followed the solitary intensive AGW at a distance more than 4000 km. However, we observed such phenomenon only within the territory with high values of “vertical” TEC and steep gradients of TEC. Apparently, these conditions are necessary for generation of SS waves due to propagation of LS AGW.