基于代理模型的二元收扩喷管流道型面优化设计

在二元收扩（2D-CD）喷管设计参数对喷管气动性能影响研究的基础上,以获得尽可能高的喷管推力系数为目标,以喉道宽高比、喉道型面半径比、收敛半角和扩张半角为设计变量,对二元收扩喷管的流道型面进行了优化设计。设计过程中,利用正交试验设计方法确定初始样本点,建立喷管推力系数与设计参数间的Kriging代理模型,采用自适应模拟退火算法（ASA）对代理模型进行分析求解。结果表明,二元收扩喷管的优化型面参数为:喉道宽高比为6,喉道型面半径比为0.3,收敛半角为15°,扩张半角为5.64°,此时最大推力系数为0.97847,流量系数为0.98778.      

Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

Prediction of cutting forces in ball-end milling of 2.5D C/C composites

Machining of carbon/carbon (C/C) composite materials is difficult to carry out due to its high specific stiffness, brittleness, anisotropic, non-homogeneous and low thermal conductivity, which can result in tear, burr, poor surface quality and rapid wear of cutters. Accurate and fast pre-diction of cutting forces is important for milling C/C composite materials with high quality. This paper presents an alternative cutting force model involving the influences of the directions of fiber. Based on the calculated and experimental results, the cutting forces’ coefficients of 2.5D C/C com-posites are evaluated using multiple linear regression method. Verification experiment has been car-ried out through a group of orthogonal tests. Results indicate that the proposed model is reliable and can be used to predict the cutting forces in ball-end milling of 2.5D C/C composites.     

基于冷态叶型生成叶片加工坐标的方法

建立了基于冷态叶型生成叶片加工坐标的方法,包括排序、插值加密、叠加位移量、去倒圆及端区叶型拟合等步骤.以某多级轴流压气机为例,应用该方法生成的加工坐标叶片除端区外主流通道叶高内误差在0.01mm以下,叶片表面波纹度和前后缘曲率良好.通过进口级的数值模拟表明:该方法生成的加工坐标叶片与冷态叶型的误差对气动性能影响小,流量-总压比-等熵效率特性变化微小,叶片进出口气流速度、方向及流场细节等变化较小,满足工程应用的需求.      

A dimension reduced INS/VNS integrated navigation method for planetary rovers

Inertial navigation system/visual navigation system (INS/VNS) integrated navigation is a commonly used autonomous navigation method for planetary rovers. Since visual measurements are related to the previous and current state vectors (position and attitude) of planetary rovers, the performance of the Kalman filter (KF) will be challenged by the time-correlation problem. A state augmentation method, which augments the previous state value to the state vector, is commonly used when dealing with this problem. However, the augmenting of state dimensions will result in an increase in computation load. In this paper, a state dimension reduced INS/VNS integrated nav-igation method based on coordinates of feature points is presented that utilizes the information obtained through INS/VNS integrated navigation at a previous moment to overcome the time rel-evance problem and reduce the dimensions of the state vector. Equations of extended Kalman filter (EKF) are used to demonstrate the equivalence of calculated results between the proposed method and traditional state augmented methods. Results of simulation and experimentation indicate that this method has less computational load but similar accuracy when compared with traditional methods.     

旋转冲压压缩转子试验系统通流部分数值研究

为了评估旋转冲压压缩转子试验系统的气动性能,采用Fluent软件对其通流部分在设计转速下的流场进行了全通道数值模拟。分析了旋转冲压压缩转子达到最高效率时,试验系统各部分的总体性能以及导叶段、旋转冲压压缩转子段和出口支板段的流动特征。计算结果表明,进口段和导叶段内气流损失较小,总压恢复系数分别为0.995和0.979,且气流在导叶内基本实现了预期的偏转和加速。旋转冲压压缩转子压比较高,单转子压比可到2.756。超声速压缩面区域不同节距方向的激波系结构有较大差异,同时存在正常反射和马赫反射现象。出口支板段存在大范围的流动分离,不利于出口气流顺畅的流出。     

基于动态面控制的多弹协同制导控制方法

为实现多枚导弹对目标进行饱和攻击,基于动态面控制理论设计了具有攻击时间约束的制导控制方法.综合弹目距离方程和动力学方程建立了制导控制一体化模型,改进设计了基于弹目距离信息的协同策略;考虑导弹速度变化、目标运动、导弹框架角受限以及避免控制器奇异等因素,设计了协同策略中的关键参数,并给出了导弹群理想协同攻击时间的选取方法.在导弹控制输入受限的前提下,采用动态面控制理论设计了导弹扰动鲁棒控制器.仿真结果表明,所提方法能够在满足多种约束的前提下,以较高的精度实现对目标的饱和攻击.     

加装吊舱对飞机操稳特性的影响及其尺寸界定

在机身等部位加装吊舱会导致飞机气动外形发生变化,为保证飞行安全,需要评估吊舱对飞机操稳特性的影响.通过CFD方法计算了某型飞机在加装不同尺寸吊舱下的气动特性,在原型机基础上通过增量法建立飞机飞行动力学模型,以必要的操稳特性指标为依据,评估加装吊舱对原型机操稳特性的影响,并结合飞行品质标准及飞机使用限制,给出了吊舱尺寸界限.结果表明,加装吊舱对原型机短周期模态、螺旋模态、定常直线平飞和俯仰拉升时的操纵有一定的影响,依据影响绘制尺寸界定区域图可为飞机改装提供依据.     

唇口几何参数对短舱进气道性能影响数值研究

针对下一代民用涡扇发动机短舱长径比不断缩小的发展趋势,为改善发动机进口气流参数分布不均、改善进气道的流场结构、提高其气动性能,开展了进气道唇口关键几何参数对短舱进气道流动特性影响的研究。通过CFD数值模拟方法研究了进气道收缩比、唇口超椭圆指数以及唇口超椭圆长短轴比对短舱进气道性能的影响。研究发现,这三个设计参数改变时,均会对进气道性能产生直接的影响,对畸变指数的影响最明显,其中收缩比改变的影响最大,当收缩比每改变0.025,畸变指数的变化率最大可达到50%。进口收缩比的改变影响喉道截面的流动,超椭圆指数变化影响了进口前缘曲率的变化,而超椭圆长短轴比变化影响了进气道唇口内型面的曲率;超椭圆长短轴比越大,超椭圆指数越小,收缩比越大,唇口初始压力损失越大,壁面摩擦损失越大,进气道总压恢复系数越低,畸变程度越高。     

深冷组合循环发动机吸气模态循环分析与设计可行域研究

为了研究类似SABRE3结构的深冷组合循环发动机,建立了基于部件法的发动机设计点热力学计算模型,提出了发动机氦循环新的循环效率和循环特征参数的定义。考虑发动机参数的物理限制条件及不同工质循环之间的相互影响,求解得到了空气路、氦气路重要参数的设计可行域。在可行域内开展了空气路和氦气路的循环分析,获到了冷却当量比、性能参数等主要参数的分布结果。结果表明:此发动机空气热功转换比ηt2为0.02～0.746。氦循环设计可行域受ηt2及换热器热负荷限制;循环起始温度和热负荷限制确定的情况下,ηt2越低氦循环可行域越窄。降低发动机冷却当量比的关键是:提高换热器1的氦出口温度以降低氦流量;当换热器1和换热器2的氦出口温度同时取得最大值时,冷却当量比取得最小值。换热器1和2的氦出口温度分别取1200K和1300K时,空气路可行域内冷却当量比为0.917～2.64。