基于MAV形变控制的鼓包装置几何分布优化

 提出了在微型飞行器(Micro Air Vehicle —MAV) 表面安装鼓包控制装置进行姿态控制的思路,针对某无尾MAV ,研究了单点鼓包凸起对气动力、气动力矩的敏度影响;以此为基础,选择了4 个鼓包控制组及相应候选控制点,利用遗传算法进行了气动、控制学科的并行优化,并对优化设计方案的控制响应特性进行了分析,表明方案可行。     

内爆炸圆管破片初速研究

分析内爆炸圆管膨胀破碎过程的应力,提出确定内爆炸圆管断裂半径的复合判据,从理论上预测不同材料圆管的破片初速度.采用GSJ高速摄影记录仪测试不同材料圆管的破片初速度,并与理论预测值行比较.结果表明,采用复合判据得到的理论预测结果与实验测量结果能够较好吻合.     

铝合金型材柔性垫弯曲成形实验研究

进行两种典型铝合金型材的弯曲实验,研究主要工艺参数对弯曲过程的影响.结果表明,型材的截面形状、相对厚度及抗弯截面系数等是决定弯曲性能的主要因素.压辊的压入深度、柔性垫的性能以及型材的约束方式等是影响弯曲半径、截面变化的关键.对实验中主要缺陷和质量问题的产生及其控制进行分析和讨论.     

从系统仿真谈仿真模型的生成

随着计算机科学和系统科学的发展，系统仿真技术愈来愈为人们所关注。其应用范围遍及政治、经济、军事、交通运输、通讯、科学实验、教学及生产管理等社会各部门及领域。而构造仿真模型又是系统仿真中非常重要且必不可少的关键环节。本文对系统仿真模型的生成问题进行了探讨。     

大攻角流动的非定常特性分析

本文首先通过动态测量手段研究了大攻角流场中的能量成分,分析了各种成分引发的非定常性对大攻角流动的影响。结果表明大攻角流动本身是一种“涡行为”,非定常性对大攻角流动非对称性的影响较弱,影响大攻角流动的本质因素是涡的动力不稳定性对于前体不确定小扰动的响应。     

一种新型的动态瞄准装置

介绍了一种新型的动态瞄准装置，描述了其光学原理、电路组成等。通过实验验证了其合理性和可行性。     

Kinetic Monte Carlo Simulation of EB-PVD Film:Effects of Substrate Temperature

The 2D kinetic Monte Carlo (KMC) simulation was used to study the effects of different substrate temperatures on the microstruc-ture of Ni-Cr films in the process of deposition by the electron beam physical vapor deposition (EB-PVD). In the KMC model, substrate was assumed to be a “surface” of tight-packed rows, and the simulation includes two phenomena: adatom-surface collision and adatom diffusion. While the interaction between atoms was described by the embedded atom method, the jumping energy was calculated by the molecular static (MS) calculation. The initial location of the adatom was defined by the Momentum Scheme. The results reveal that there exists a critical substrate temperature which means that the lowest packing density and the highest surface roughness structure will be achieved when the temperature is lower than the smaller critical value, while the roughness of both surfaces and the void contents keep decreasing with the substrate temperature increasing until it reaches the higher critical value. The results also indicate that the critical substrate temperature rises as the deposition rate increases.     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

考虑可压缩与热传导的壁面函数边界条件及其应用

考虑到可压缩和热传导效应的壁面函数边界条件,被耦合到了采用k-ω两方程湍流模型、用有限体积法求解N-S方程的程序中。壁面函数基于耦合的速度和温度型,并且在边界层内的粘性子区和对数区内一致有效。引入壁面函数边界条件后,通过算例验证在y <100的范围内,得到的物面压力、摩阻、热流与实验结果比较,结果可靠。而无壁面函数边界条件时,要得到相同精度的结果,要求y ≈1。壁面函数的引入,为工程上准确预测飞行器在湍流流动中表面受力与气动热提供了保障。     

基于POWER PC通用处理器的CPU模块设计

POWER PC通用处理器是一种低功耗超标量的RISC处理器。本文描述了基于POWER PC通用处理器的CPU模块的基本体系结构,并以Motorola通用处理器POWER PC603e为例,阐述了CPU模块的实现方法。