悬索桥颤振主动抑制研究

选用二次型性能指标，把悬索桥颤振主动抑制问题转化为线性二次型高斯问题，设计了颤振主动抑制的最优滤波器及最优控制律，其中，经ｏｇｅｒ有理近似拟合气动力自激项，对脉动风的描亭旭结为成型滤波器设计；稳定性判定归结为根轨迹图的判断；抖振响应计算归结为Ｌｙａｐｕｎｏｖ方程求解，以某悬索桥为算例，计算结果表明：对该类桥梁进行颤振主动抑制，效果良好，最优控制设计所得结论对工程具有一定参考价值。     

利用双目标优化寻求颤振抑制控制律

本文对一个三角机翼/外挂系统的颤振主动抑制进行了系统的研究。在理论上,对如何应用现代控制理论设计优化控制律进行了探讨;对非定常气动力拟合的Pade矩阵近似作了改进;提出了用理想极点和二次型性能指标进行双目标优化来确定加权矩阵的思想;在实现上,用状态观测器和单秩法极点配置两种方法设计了输出反馈控制律。风洞实验结果表明:用本文的方法所综合的控制律是合适有效的,成功地使机翼/外挂系统的颤振速度提高了15.7％,与理论计算结果吻合良好。     

含多部位损伤搭接结构应力强度因子三维有限元分析

应力强度因子(Stress intensity factor,SIF)分析是含多部位损伤(Multiple site damage,MSD)结构剩余强度和裂纹扩展寿命预测的基础和关键。考虑接触与摩擦,建立了含MSD搭接结构的三维有限元模型,研究了不同裂纹长度、铆钉类型以及损伤模式下裂纹尖端SIF分布情况和变化规律。结果表明,搭接件孔边裂纹Ⅰ型SIF起主导作用,Ⅱ型和Ⅲ型SIF可忽略不计。由于次弯曲、铆钉变形和板厚度等因素,SIF在外表面最小,接触面一侧较大,最大值多位于蒙皮内部。MSD会使裂纹间的干涉作用增强,SIF增大,且裂纹间距离越近干涉作用越强。裂纹长度相同时,埋头铆钉的孔边裂纹SIF积分均值大于平头铆钉,且接触面的SIF埋头铆钉大于平头铆钉,外表面则相反。     

冯子明 航空信息化专家

我国航空企业数字化制造已经有哪些成就,为我国航空企业带来怎样的影响?冯子明:目前国内飞机数字化设计制造水平在不断地提高。数字化的软硬件环境已初具规模,飞机设计已由三维几何模型设计向全信息三维模型设计方向发展     

工业机器人在飞机数字化装配中的应用

通过对当今工业机器人技术的发展和背景的分析,表明该技术在飞机装配中的重要价值,并分列阐述出智能工业机器人在飞机装配中的八大主要应用环节。指出在发展工业机器人技术应用中的主要关键技术。并对其在航空领域的发展方向和趋势进行了展望。     

Analysis for Strength Test of Butt-jointed Thin-wall Steel Pipe

目前薄壁钢管对接焊缝强度的计算常采用参考文献[1]中公式,此公式为国外早期的经验计算公式,但仅适用于气焊钢管,而薄壁钢管常采用C02保护焊.本文通过焊接钢管拉伸试验分析,推导出了适用于计算薄壁焊接钢管对接焊缝强度的公式以及CO2保护焊参数取值.     

Ionospheric scintillations at Guilin detected by GPS ground-based and radio occultation observations

The occurrence of ionospheric scintillations with S4 ? 0.2 was studied using GPS measurements at Guilin, China (25.29°N, 110.33°E; geomagnetic: 15.04°N, 181.98°E), a station located near the northern crest of the equatorial anomaly. The results are presented for data collected from January 2009 to March 2010. The results show that nighttime amplitude scintillations only took place in February and March of the considered years, while daytime amplitude scintillations occurred in August and December of 2009. Nighttime amplitude scintillations, observed in the south of Guilin, always occurred with phase scintillations, TEC (Total Electron Content) depletions, and ROT (Rate Of change of TEC) fluctuations. However, TEC depletions and ROT fluctuations were weak during daytime amplitude scintillations, and daytime amplitude scintillations always took place simultaneously for most of the GPS satellites which appeared over Guilin in different azimuth directions. Ground-based GPS scintillation/TEC observations recorded at Guilin and signal-to-noise-ratio (SNR) measurements obtained from GPS-COSMIC radio occultation indicate that nighttime and daytime scintillations are very likely caused by ionospheric F region irregularities and sporadic E, respectively. Moreover, strong daytime amplitude scintillations may be associated with the plasma density enhancements in ionospheric E region caused by the Perseid and Geminid meteor shower activities.     

PLC实现机床主轴自动换挡

以一台数控五坐标机床技术改造为实例，采用 Ｐ Ｌ Ｃ 实现主轴的自动换挡。通过状态及数据接口分析，提出主轴换挡的控制流程，总结出在机床控制中主轴换挡控制的一般原理与方法。     

小波去除噪音算法研究

介绍了小波变换滤除噪音的机理和与傅立叶变换相比的优越性，其中包括确定性噪音和随机噪音。讨论了增强去噪效果的几种改进方案并提出一种试验估计去噪方法，对工程应用有一定的实用价值。     

Passive target tracking using maximum likelihood estimation

Estimation of target trajectory from passive sonar bearings and frequency measurements in the presence of multivariate normally distributed noise, with unknown inhomogeneous general covariance, is modeled as a nonlinear multiresponse parameter estimation problem. It is shown that maximum likelihood estimation in this case is identical to optimizing a determinant criterion which has a concise form and contains no elements of unknown covariance matrix. A Gauss-Newton type algorithm using only the first-order derivatives of the model function and a new convergence criterion, is presented to implement such estimation. The simulation results demonstrate that performance of the maximum likelihood estimation method with the above noise model is superior to that with the traditional noise assumption