空气中微细电火花沉积铜合金工艺方法

提出了一种在空气中将工具电极丝黄铜材料沉积到工件上的新工艺方法。实现该方法的基本条件为:(1)工具电极接脉冲电源正极;(2)在空气中放电;(3)窄脉宽配合宽脉间。通过大量实验对微细电火花沉积加工的工艺规律进行了系统深入的研究,得出各主要工艺参数对沉积工艺效果的影响规律。最终以黄铜电极丝为工具电极,在高速钢工件表面上沉积出直径为0.19 mm、高度为7.35 mm的微小圆柱体。利用SEM、能谱分析和X射线衍射及显微硬度测试等方法对沉积物进行分析,得出该沉积物的组织结构、化学成分和硬度等方面的基本性质,为进一步研究三维沉积加工奠定了基础。     

基于IRL技术的智能采样系统设计

在模拟信号易受干扰、不稳定的环境下 ,普通的采样系统往往不能适用 ,常常会因采样不准确而导致控制电路产生错误的控制信号 ,造成系统运行故障。我们采用基于IRL技术实现的采样电路系统能通过TCP IP远程监控采样电路的状况 ,并能在采样信号出错的情况下通过硬件重构进行信号增益、滤波等处理 ,消除模拟信号因外界干扰带来的变化影响 ,IRL技术给采样系统带来了高安全、高稳定以及易维护的特性     

典型电离层多普勒记录及其讨论

由于地面电离层多普勒频率偏移测量具有时间连续、设备相对简便等固有特征，它特别适合于扰监测。本文在整理北京大学电离层高频多普勒台站观测资料的基础上，给出了一些典型电离层多普勒效应观测现象，这些现象反映了多普勒的细致分析对电离层形态学研究有其特殊意义。利用IRI模型，对多普勒频移的太阳耀斑效应及电离层不规则结构对多普勒频移的影响进行了模拟计算，理论结果与观测基本一致，从而大体上解释了这些响应的物理机制。论文最后对观测到的一种特殊的记录类型－－S型描迹的具体成因作了详细的分析和讨论，指出在一定条件下，以一定相位速度水平传播的声重波可以产生这类记录，给出了相位速度和振幅等声重波参数与记录描迹形状的关系，这对从多普勒频移记录推演电离层中的波动特征有一定的帮助。     

MONITORING OF ENERGETIC PARTICLE ENVIRONMENT INSIDE THE CHINA-BRAZIL EARTH RESOURCE SATELLITE

On 14 October 1999, the Chinese-Brazil earth resource satellite (CBERS-1) was launched in China. On board of the satellite there was an instrument designed at Peking University to detect the energetic particle radiation inside the satellite so the radiation fluxes of energetic particles in the cabin can be monitored continuously. Inside a satellite cabin, radiation environment consists of ether penetrated energetic particles or secondary radiation from satellite materials due to the interactions with primary cosmic rays.Purpose of the detectors are twofold, to monitor the particle radiation in the cabin and also to study the space radiation environment The data can be used to study the radiation environment and their effects on the electronics inside the satelhte cabin. On the other hand, the data are useful in study of geo-space energetic particle events such as solar proton events, particle precipitation and variations of the radiation belt since there should be some correlation between the radiation situation inside and outside the satellite.The instrument consists of two semi-conductor detectors for protons and electrons respectively. Each detector has two channels of energy ranges. They are 0.5-2MeV and ≥2MeV for electrons and 5-30MeV and 30-60MeV for protons. Counting rate for all channels are up to 104/(cm2@s)and power consumption is about 2.5 W. There are also the additional functions of CMOS TID (total integrated dose) effect and direct SEU monitoring. The data of CBMC was first sent back on Oct. 17 1999 and it's almost three years from then on. The detector has been working normally and the quality of data is good.The preliminary results of data analysis of CBMC not only reveal the effects of polar particle precipitation and radiation belt on radiation environment inside a satellite, but also show some important features of the geo-space energetic particle radiation.As one of the most important parameters of space weather, the energetic charged particles have great influences on space activities and ground tech nology. CBMC is perhaps the first long-term on-board special equipment to monitor the energetic particle radiation environment inside the satellite and the data it accnmulated are very useful in both satellite designing and space research.     

利用MF雷达对耀斑期间电离层D区电子密度的观测研究

利用MF雷达观测资料对X级别耀斑爆发期间在66-80km高度之间的电子密度进行了研究，观测到了耀斑爆发期间电子密度的突然增加，在较低高度上的电子密度的时间变化趋势与耀斑的软X射线辐射通量相关．电子密度的变化强度依赖于具体的耀斑参数，有些耀斑引起的电子密度增加高达400cm^-3，有些仅为100cm^-3左右．但耀斑期间在这一高度区间增加的总电子含量增量仅占耀斑辐射引起的整个电离层总电子含量增量的千分之一左右．最后，利用恢复阶段电子密度的时间变化过程估算了1997年11月4日耀斑期间部分高度上的有效复合系数．     

An innovative study on low surface energy micronano coatings with multilevel structures for laminar flow design

Laminar flow design is one of the most effective ways to reduce the drag of a commercial aircraft by expanding the laminar flow region on the surface of the aircraft. As material science develops, the emergence of new materials such as low surface energy materials has offered new choices for laminar flow design of commercial aircraft. Different types of low surface energy micro-nano coatings are prepared to verify the effects on the boundary layer transition position and the drag of the airfoil through wind tunnel tests. The infrared thermal imaging technology is adopted for measuring the boundary layer transition, while the momentum integral approach is employed to measure the drag coefficient through a wake rake. Infrared thermal imaging results indicate that the coatings are capable of moving backward the boundary layer transition position at both a low velocity of Mach number 0.15 and a high velocity of Mach number 0.785. Results of the momentum integral approach demonstrate that the drag coefficients are reduced obviously within the cruising angle of attack range from 1° and 5° by introducing the low surface energy micro-nano coating technology.     

甲醇超临界水完全气化制氢系统的火用分析

基于热力学火用平衡方程所揭示的实际用能过程和理想用能过程,通过引入"偏离值"、"偏离度"两个指标,对甲醇超临界水制氢系统进行了火用分析。首先确定了加热和反应环节为重点优化环节;然后研究了此二环节的"偏离度"分别随压力、温度的变化规律,并比较了压力和温度对"偏离度"的影响作用大小。在提高甲醇制氢系统的能质利用率方面进行了有益的探讨,其结论对制氢系统的节能工作具有一定的参考价值。     

某型灯光告警设备实装训练系统的研制

灯光告警是飞机重要的飞行安全监护设备,采集各系统的故障告警信息,经分析处理后,以醒目的灯光及时提示飞机驾驶员进行处置,对确保飞行安全具有关键作用.为提高维护人员对灯光告警设备的维修保障能力,设计了一套灯光告警设备实装训练系统,该系统能够模拟产生飞机各系统的故障告警信息,直观展示故障告警现象和故障处置流程,通过操作训练,使维护人员掌握灯光告警设备的操作使用流程和典型故障排除方法.     

GAP/环氧化合物体系胶片的制备与性能表征

为探索一种新型非异氰酸酯固化体系,以端羟基聚叠氮缩水甘油醚(GAP)为研究对象,三羟甲基丙烷三缩水甘油醚(TMPTGE)为固化剂,通过实验筛选出六亚甲基四胺(HA)为固化催化剂,对GAP/TMPTGE/HA固化体系进行了研究。通过拉伸试验、DMA试验,研究了固化参数R和固化时间对GAP/TMPTGE胶片力学性能的影响,借助非等温DSC法,研究了GAP/TMPTGE/HA体系的固化动力学特征,并通过TG实验对胶片热性能进行了表征。结果表明,随着固化参数R的增大,胶片的断裂伸长率先增加后降低,拉伸强度不断增大;R=3.0时,胶片断裂伸长率达到最大值98%,此时拉伸强度为0.67 MPa,玻璃化转变温度为-34.8℃;胶片热分解分为2个阶段,对应的分解峰温分别为250℃和350℃。     

新一代战斗机非定常流动数值研究综述

新一代战斗机强调超机动能力和强隐身性，其中大攻角下的静态失速、动态失速及内埋弹仓绕流是与高机动和强隐身密切相关的、极具挑战的几类典型的非定常流动，它们对数值方法提出了极高的要求。为了高精度地仿真流场、清楚地揭示流动机理，有效地控制非定常流动，非常有必要发展高精度且高效率的RANS-LES混合方法体系，包含RANS-LES混合方法本身、与RANS-LES混合方法匹配的高精度自适应耗散格式、基准湍流模式、高质量计算网格、高精度时间推进方法、非定常量的统计方法等，具有极强的紧迫性。提出、发展、验证并应用该类方法数值仿真新一代战斗机（包括单独部件、组合体、甚至全机）的非定常流动，数值预测结果与风洞实验数据吻合良好；此类方法可为新型战斗机设计提供理论依据和分析手段。