A comprehensive survey on the methods of angle of attack measurement and estimation in UAVs

Angle of Attack (AOA) is a crucial parameter which directly affects the aerodynamic forces of an aircraft. The measurement of AOA is required to ensure a safe flight within its designed flight envelop. This paper intends to summarise a comprehensive survey on the measurement techniques and estimation methods for AOA, specifically in Unmanned Aerial Vehicle (UAV) applications. In the case of UAVs, weight constraint plays a major role as far as sensor suites are concerned. This results in selecting a suitable estimation method to extract AOA using the available data from the autopilot. The most feasible and widely employed AOA measurement technique is by using the Multi-Hole Probes (MHPs). The MHP measures the AOA regarding the pressure variations between the ports. Due to the importance of MHP in AOA measurement, the calibration methods for the MHP are also included in this paper. This paper discusses the AOA measurement using virtual AOA sensors, their importance and the operation.     

Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

精仪工作台定量调整的原理及方法

论述了可调结构仪器工作台的结构、调整原理和调整方法，并以三点支撑结构、锥面支撑结构仪器工作台表面与测量轴线垂直度的调整为例，具体地阐述了调整方法和步骤。     

薄膜充气管充气展开特性试验

用展开导轨消除因重力产生的摩擦力,在不同充气速率与初始展开角条件下对薄膜材料充气管的充气展开特性进行了试验研究,获得了展开角,以及展开加速度和内气压的变化规律。试验及分析结果表明:充气管的充气膨胀与展开相互独立,充气膨胀过程近似为等压增容过程,折叠部位的气压变化特性与整体气压变化特性差异明显。     

关于加大产业结构调整力度的思考

本文从我国产业结构调整的现状及存在的问题出发，针对一般加工产业生产能力过大，高水平的加工能力不足这一突出问题进行了原因分析，在此基础上，就我国加速优化产业结构的客观基础和可能，提出了关于加大产业结构调整力度的七点思考建议。     

利用偏馈振子调整测控雷达跟踪通道相移技术研究

提出一种调整雷达跟踪通道相移的方法 ,即在雷达天线主面上配置偏馈振子 ,利用偏馈振子做为校准源调整雷达跟踪和 /差通道间的相移 ,并对该方法的可行性、可靠性及稳定性进行了实验研究。     

基于分段常滑翔角的长航时纵向远程滑翔飞行方程近似解

提出用包含地球旋转效应的n个常滑翔角飞行段近似实际滑翔飞行轨迹的方法。基于该方法推导了长航时纵向远程滑翔飞行轨迹近似解，并给出了各段常滑翔角、滑翔时间的求解方法及整个滑翔轨迹近似计算步骤。文中算例结果表明，该近似求解方法计算得到的滑翔航程和滑翔时间与实际值相差很小，航程误差率约为0．7％，时间误差率约为0．6％，因此该方法在近似小初始滑翔角的长航时远程纵向滑翔飞行时是有效的、可行的，尤其针对航程在地球半圈以上的滑翔飞行轨迹。     

基于一维相控阵引信的起爆控制算法研究

工程上实现最佳引战配合要求导弹战斗部最大破片密度方向瞄准目标要害部位。基于一维相控阵引信的波束控制技术,推导了最佳起爆角和起爆延时算法,并研究了一种改进卡尔曼滤波方法在此算法中的应用。该滤波算法将球坐标系中导弹导引头的测量信息转换到直角坐标系下进行滤波,同时消除了由于坐标转换而引起的偏差。仿真结果表明,该滤波算法的应用能得到很高的最佳起爆角和起爆延时估计精度。     

多层RAM涂层对任意入射角电磁波的反射特性分析

为了解决结构型吸波材料的分析和设计中所遇到的反射系数计算问题，从电磁场理论出发，导出了电磁波以任意角入射时多层雷达吸波材料（RAM）涂层的反射系数公式，此法简单易行，为结构型吸波材料的计算机辅助分析和设计提供了基础，同时给出了计算曲线的例子，通过实例计算分析了电磁波的入射角，极化状态等对反射特性和隐身效果的影响。