Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

沉井技术在码头改造工程中的应用

沉井依靠自重消除刃脚阻力和外壁摩擦力下沉,本文对该项工艺的下沉、纠偏、挖土、封底主要技术问题进行介绍。     

多级串联密封系统泄漏规律及应用研究

多级串联密封结构的泄漏过程非常复杂,其泄漏规律对多级密封结构的设计、检漏和密封安全评估等具有重要意义。建立了多级串联密封系统的数学模型,揭示了多级串联密封结构正压泄漏的漏率、漏量与泄漏时间关系的一般规律,通过三级密封系统泄漏的仿真计算实例和泄漏实验,验证了多级串联密封泄漏理论的正确性,并总结了多级串连密封泄漏规律的应用方法。     

篦齿封严装置减振方法研究及减振装置设计

本文研究了用于篦齿封严装置的干摩擦式阻尼减振器的减振原理,采用篦齿封严装置气弹稳定性分析方法,分别研究了用于篦齿封严装置的阻尼环和阻尼套筒的减振效果,并在此基础上提出了阻尼减振器的工程设计方法。研究表明,干摩擦式阻尼减振器可以有效地提高篦齿封严装置的气动弹性稳定性。     

Flow mechanism between purge flow and mainstream in different turbine rim seal configurations

The rim seal is used to prevent mainstream ingestion to the gap between the vane of a turbine and its blade. In this article, the dolphin lip with a hook configuration and a large seal cavity with hook structures are designed based on the high-pressure turbine datum single shark lip rim seal configuration. The sealing effect and parameters of the flow field are measured by an experiment method and a numerical simulation is used to explain the mechanism. For three configurations, the effect of the leakage slot vortex on the efficiency of the seal and the influence of leakage vortex, generated by the interaction between purge flow and mainstream flow, are discussed in depth. The result shows that the reverse vortex formed by the dolphin lip rim seal with hook structure will increase the sealing efficiency. The seal configuration with a large cavity improves sealing efficiency to a greater extent than the datum structure. At different purge flow rates and with unequal seal structures, the purge flow produces three types of leakage vortices in the passage. Besides, the seal configuration with dolphin lip produces a Kelvin-Helmholtz instability at the interface of the purge and the mainstream flows at a low purge flow rate to induce new leakage vortex branches in the passage of the blade.     

某型飞机机翼整体油箱工艺研究

介绍了某型机机翼整体油箱的研制过程,针对总体气动、结构和使用维护等对整体油箱提出的性能要求,工程部门相应采用严格的环境措施、确保协调精度的预装配措施以及湿连接、密封装配措施等,解决了研制过程中诸多关键难题,保证了整体油箱的研制进度和产品质量,经各种试验检测和试飞考核,该整体油箱质量稳定可靠,性能良好。     

Leakage performance of floating ring seal in cold/hot state for aero-engine

Rotating experimental investigations were carried out to study the oil sealing capability of two different floating ring seals in cold/hot state for aero-engine. High-speed Floating Ring Seal(HFRS) is a seal with the inner diameter of 83.72 mm and maximum speed of 38000 r/min, and Low-speed Floating Ring Seal(LFRS) is another seal with the inner diameter of 40.01 mm and maximum speed of 18000 r/min. In hot state, sealing air with the temperature of 371 K and oil with the temperature of 343 K was employed to model the working conditions of an aero-engine. Comparisons between floating ring seal and labyrinth seal were done to inspect the leakage performance.More attention was paid to the critical pressure ratio where the oil leakage began. Results show that the critical pressure ratio in cold state is obviously larger than that in hot state for both seals. An underlying sealing mechanism for floating ring seal is clarified by the fluid film, which closely associates with the dimensionless parameter of clearance over rotating diameter(2 c/Dr). Another fantastic phenomenon is that the leakage coefficient in hot state, not the leakage magnitude, is unexpectedly larger than that in cold state. Overall, the leakage performance of the floating ring seal is better than the labyrinth seal.     

金属密封件镀金工艺研究

介绍了金属密封件镀金工艺技术,该工艺采用亚硫酸盐镀金方案,以单脉冲电源为镀覆电源,以预镀镍层为中间镀层来制备金镀层,得到了结晶细致、厚度均匀并与基体上结合牢固的金镀层.研究了金镀层的沉积速率和结合强度,观察了镀层的表面形貌和组织结构,进行了金属密封件气密性试验和典型试验.结果表明：金属密封件金镀层的技术性能指标满足设计要求,能够应用于液体火箭发动机中,该发动机已通过地面热试车考核.     

典型流阻元件的流量和熵产模型研究

为揭示流阻元件的流动损失机理,本文从热力学理论出发,建立了流阻元件的质量流量模型和熵产模型,分析了质量流量与熵产之间的关系,研究了熵产随系统压比和进口总压的变化情况,并通过预旋喷嘴和篦齿封严的实验结果对两个模型进行了分析评估。结果表明,质量流量模型与实验结果的最大偏差不超过2.8%;熵产模型与实验结果的最大偏差不超过1.9%。系统熵产随系统压比的增加而增大,随进口总压的增加而减小。当系统的进口总压,进口总温和出口静压不变时,模型中的参数a是衡量不同元件熵产大小的唯一量度。     

基于三维模型的偏心鼓筒气动特性分析

为了获取篦齿封严鼓筒齿腔内的压力分布,掌握鼓筒气动特性情况,建立了带封严篦齿鼓筒的三维流场通道模型,计算转静子同心和不同偏心量条件下鼓筒表面静压,分析气动载荷作用下鼓筒的力学特性.仿真结果表明:偏心量的变化使表面静压出现复杂变化,周向静压幅值变动明显,最大偏心量下的静压幅值比无偏心时增长3倍;偏心引起的周向静压波动使鼓筒应力幅值最大浮动3%左右.