Unsteady wakes-secondary flow interactions in a high-lift low-pressure turbine cascade

Detailed experimental measurements were conducted to study the interactions between incoming wakes and endwall secondary flow in a high-lift Low-Pressure Turbine (LPT) cascade. All of the measurements were conducted in both the presence and absence of incoming wakes, and numerical analysis was performed to elucidate the flow mechanism. With increasing Reynolds number, the influence of the incoming wakes on suppressing the secondary flow gradually increased owing to the greater influence of incoming wakes on reducing the negative incidence angle at higher Reynolds numbers, leading to a lower blade loading near the leading edge and suppression of the Pressure Side (PS) leg of the horseshoe vortex. However, the effect of unsteady wakes on suppressing the profile losses gradually became weaker owing to the reduced size of the Suction Side (SS) separation bubble and increased mixing loss in the free-flow region at high Reynolds numbers. Incoming wakes clearly improved the aerodynamic performance of the low-pressure turbine cascade at low Reynolds numbers of 25,000 and 50,000. In contrast, at the high Reynolds number of 100,000, the profile loss at the midspan and mass-averaged total losses downstream of the cascade were higher in the presence of wakes than in the absence of wakes, and the unsteady wakes exerted a negative influence on the aerodynamic performance of the LPT cascade.     

超燃燃烧室一维流场分析模型的研究

对公开发表的用于超声速燃烧流场分析的几种一维模型进行了研究,指出了其中存在的问题。研究结果表明:基于实验静压数据的一维模型,若不借助必要的流场测量数据或分析结果,或借助于经验性的处理方法,单靠一维假设,无法获得较为完整的一维流场分析结果。改进后的一维模型降低了数据处理过程中的不确定性,提高了对一般情况的适应能力。用编制的计算程序SSC-2对两组典型的超燃燃烧室壁面静压实验数据进行了演算,取得了燃烧室出口总压恢复系数的计算值与测量值基本一致的好结果。     

固冲发动机补燃室流场的实验校测

1引言目前数值模拟已广泛应用到火箭发动机的流场分析中,特别是固冲发动机补燃室的燃烧和流动[1,2]。但是这种方法在固冲发动机补燃室应用的有效性还没有合适的实验验证。国外开展的补燃室流动实验大多以水为介质,用片光流动显示的方法观察流场的概貌,与真实发动机的流动之间存     

吸力面翼刀对压气机叶栅内二次流的影响

1引言在叶轮机械叶栅内流动控制中,可以通过在叶片吸力面、端壁上安装翼刀或隔片,控制二次流的发展,降低二次流损失,其中将翼刀加装在吸力面上的控制方式即为吸力面翼刀控制技术。吸力面翼刀主要是通过阻断端壁附面层和叶片吸力面附面层近端壁处低能流动沿吸力面的展向迁移来对     

环形燃烧室性能计算

在任意曲线坐标系下对包括扩压器和火焰筒在内的环形燃烧室三维两相反应流进行了数值模拟。燃烧室性能采用多维经验分析法估算所用的数学模型有 κ-ε,紊流模型 ,EBU -Arrhenius紊流燃烧室模型 ,六通量热辐射模型以及颗粒群轨道模型。在非交错网格体系下 ,气相采用 SIMPLE算法和液相采用 PSIC算法求解 ,通过两种工况和三种扩压器进口速度分布计算表明 ,所得的流场各气流参数分布和燃烧室性能较合理 ,本文所建立的程序可为燃烧室优化设计和研制提供有用数据。     

燃烧室头部进气规律对煤粉燃烧效率的影响

用实验方法研究了火焰筒式煤粉燃烧室头部进气规律对燃烧效率的影响。通过对6种结构的头部配气方案的分析比较,得出了煤粉燃烧室合理的头部配气方案,为今后煤粉燃烧室的设计和工作状态的选择提供了重要的实验依据。     

Experimental investigation on silica dust lofting due to charging within micro-cavities and surface electric field in the vacuum chamber

The charged dust particles can be mobilized electrostatically by the repulsion between the adjacent grains and the surface electric field due to the incoming electron current and the charge accumulation within the micro-cavities. In this study, the experimental results of the initial vertical launching velocities and the maximum dust heights are compared with the estimated values for the lofted spherical dust grains by the patch surface charging equations. Silica particles with the sizes between <6 and 45?µm in radius are loaded on a graphite plate, and they are exposed to the electron beam with 450?eV energy under 4?×?10^?3?Pa vacuum chamber pressure. During the first set of the experiments, the dust samples are tested without an initial compression process and an additional horizontal electric field. Second, the dust samples are compressed by two different weights in order to increase the packing density under approximately 780.7?Pa and 3780?Pa. Finally, the dust grains are placed between the two parallel aluminum plates to apply approximately 2000?V/m and 4800?V/m horizontal electric field. A high-speed camera is used to record the transportation of the dust grains together with a microscopic telescope, and the results point out that the patch surface dust-charging model estimations are in agreement with the first experiments. On the other hand, the dust particles from the compressed samples are lofted with higher velocities than the estimations, and the number of the dust lofting observations decreases significantly, which demonstrates the importance of the micro-cavities and the increased charging requirement to overcome the contact forces. When the horizontal electric field is present, the initial vertical launching velocities are measured to be lower than the other experiments, which can be attributed to the decreased charging requirement for the dust lofting as a result of inter-particle collisions and rolling motion. According to the experimental results, the electrostatic dust transportation can be controlled not only by the ambient plasma and the solar irradiation on the airless planetary bodies, but also by the surface properties such as the contact surfaces between the dust grains, the number of the micro-cavities related to the packing density, and the presence of the horizontal electric field contributing to the external forces by other particle motions.     

扇形段与全环燃烧室熄火性能换算研究

为研究不同类型燃烧室试验件熄火性能之间的关系,开展了扇形段和全环燃烧室的熄火性能试验.通过试验对比了二者熄火规律的相似性和差异性,并分析了造成差异的主要因素.以Lefebvre熄火模型为基础,结合雾化数据,拟合得到扇形段与全环燃烧室的贫油熄火经验关系式,并推算出二者熄火性能的定量换算公式.结果表明:扇形段与全环燃烧室的熄火边界变化规律类似,但在相同的工作状态条件下,全环燃烧室的贫油熄火油气比小于扇形段的相应值.     

典型工况下低排放燃烧室的压力振荡特性

为了研究低排放燃烧室在典型工况下的压力振荡特性,针对模型燃烧室进行了燃烧自激振荡特性试验.在试验中测量了采用贫油预混预蒸发(LPP)燃烧技术的低排放燃烧室在典型工况下的压力振荡频率和幅值,在燃烧室进口压力为1.10～2.77MPa、燃烧室进口温度为656～845 K、燃烧室压降为3.41％～4.35％范围内,分析了燃油粒径变化对振荡特性的影响.分析结果表明:局部当量比脉动是引发燃烧不稳定的因素之一.通过计算燃油二次雾化状态下的液滴最大粒径,发现燃油液滴粒径的变化对主燃级出口处的局部当量比脉动有直接影响,从而引起燃烧室压力振荡幅值和频率的变化.     

基于自适应网格的超声速液体射流破碎过程研究

为研究超声速气流中液体横向射流的破碎过程,采用脉冲背景光方法和VOF方法开展了实验和数值研究。为提高液体横向射流中气液界面和气流场特征捕捉的精确性,采用自适应网格技术对于气液界面、激波出现位置进行网格细化,计算得到了较为精细的气液界面、激波特征及涡系结构。研究结果表明:在低成本仿真模拟条件下,利用自适应网格计算得到的射流轨迹和轮廓与实验吻合较好,射流轨迹的最大误差为10%;射流初始段在超声速气流条件下,仍然存在一段高度约为1.9倍喷孔直径且圆柱形态保持较好的连续光滑液柱。随着喷注压降的升高,液柱的长度逐渐增大;主流气体流经液柱发生三维绕流,在射流附近和近壁面区域形成不断演化的反转涡对,反转涡对的形成加速了液体射流一次破碎过程。