全文获取类型
收费全文 | 51篇 |
免费 | 24篇 |
国内免费 | 5篇 |
专业分类
航空 | 55篇 |
航天技术 | 7篇 |
综合类 | 3篇 |
航天 | 15篇 |
出版年
2022年 | 2篇 |
2021年 | 5篇 |
2020年 | 6篇 |
2019年 | 3篇 |
2018年 | 1篇 |
2017年 | 3篇 |
2016年 | 3篇 |
2015年 | 5篇 |
2014年 | 8篇 |
2013年 | 1篇 |
2012年 | 8篇 |
2011年 | 2篇 |
2010年 | 2篇 |
2009年 | 5篇 |
2008年 | 3篇 |
2007年 | 2篇 |
2006年 | 1篇 |
2004年 | 3篇 |
2003年 | 2篇 |
2002年 | 1篇 |
2001年 | 1篇 |
1999年 | 1篇 |
1997年 | 1篇 |
1996年 | 1篇 |
1995年 | 1篇 |
1994年 | 1篇 |
1992年 | 2篇 |
1988年 | 1篇 |
1986年 | 1篇 |
1985年 | 1篇 |
1984年 | 2篇 |
1983年 | 1篇 |
排序方式: 共有80条查询结果,搜索用时 234 毫秒
1.
3.
4.
今年10月28日,美国Armadillo航空航天公司研制的月球着陆器,在竞赛中因发动机问题和其他机械故障而突然起火。 相似文献
5.
钛合金是航空发动机中的常用材料,从20世纪60年代开始应用以来,钛着火故障却不绝于耳,在军用发动机和民用发动机中都出现过严重的钛着火故障,不仅有钛合金转子与钛合金静子相磨蹭引发的,也有钛合金的工作叶片与钢制机匣严重磨蹭而引发的事故,这些都应引起重视,并采取相应的措施。 相似文献
6.
This paper presents an auto-tuning method for a proportion plus integral(PI) controller for permanent magnet synchronous motor(PMSM) drives, which is supposed to be embedded in electro-mechanical actuator(EMA) control module in aircraft. The method, based on a relay feedback with variable delay time, explores different critical points of the system frequency response.The Nyquist points of the plant can then be derived from the delay time and filter time constant.The coefficients of the PI controller can then be obtained by calculation while shifting the Nyquist point to a specific position to obtain the required phase margin. The major advantage of the autotuning method is that it can provide a series of tuning results for different system bandwidths and damping ratios, corresponding to the specification for delay time and phase margin. Simulation and experimental results for the PMSM controller verify the performance of both the current loop and the speed loop auto-tuning. 相似文献
7.
药盒式点火器的工作过程可分为电引火头发火期,点火器发火期和点火药燃烧期三个时期。文中利用集总参数法分析了电引火头的点火电流、点火能量和桥絲温度的瞬态特性。报导了赛璐珞药盒点火器各延迟时间的试验测量结果,并考察了点火药量(或点火药装填密度),点火药和电引火头种类,电引火头数目以及试验温度等对延迟时间的影响。结果表明,在合理设计的药盒式点火器的整个工作时间中,点火药燃烧期一般占65%以上,而点火器发火期和电引火头发火期所占比重较小,前者略长于后者。 相似文献
8.
舵机反应时间是徇控制舱动态反应特性的关键参数,本文以影响舵机反应时间因素之一的气缸动作延迟时间,进行了分析与气动计算,推导了延迟时间计算公式,并由此了提出了改进反应时间的措施方法。 相似文献
9.
含纳米金属粉的推进剂点火实验及燃烧性能研究 总被引:12,自引:1,他引:11
利用CO2激光点火系统对含有纳米铝粉和纳米镍粉的AP/HTPB推进剂进行激光点火实验,测量了推进剂在不同激光功率和压强下的点火延迟时间,对推进剂的燃速、常压点火温度和爆热也进行了测量。同时,利用氧化还原滴定法测定燃烧残渣中活性铝含量。结果表明,纳米铝粉(n—Al)的点火阀值比普通铝粉(g-A1)的点火阀值小几个数量级,加入纳米铝粉可有效地缩短推进剂点火延迟时间。而在纳米镍粉为催化剂的协同作用下,推进剂燃速明显提高,点火延迟时间也大大减少,Al在推进剂燃烧过程中的燃烧效率得以提高,同时燃烧残渣中活性铝含量也明显降低。 相似文献
10.
针对光纤陀螺用SLD光源温控模型不准确所带来的温控系统稳定裕度不足、稳态精度差的问题,提出一种基于相角裕度补偿反推延迟环节的模型辩识方法,精确获取了SLD光源温控模型中的延迟时间常数,并据此设计了PID控制器.仿真及实验结果表明,温控系统幅值裕度、相角裕度分别优于10 dB、35°,在-20 ℃~+60 ℃温度范围内可以实现优于0.01 ℃的控温精度,有效提高了系统稳定裕度和稳态精度,满足任务需求. 相似文献