地球同步轨道长寿命卫星热控涂层太阳吸收率性能退化研究

文章介绍了15年地球同步轨道环境对卫星表面太阳吸收率性能影响的试验模拟研究,研究结果为长寿命卫星热设计及热控涂层选择和研制提供可靠依据;介绍自行研制的空间低能综合环境试验设备、太阳吸收率原位测试系统和空间低能综合环境模拟试验方法,并对航天器常用的S781白漆、SR107ZK白漆、F46镀银和OSR二次表面镜热控材料进行空间低能综合环境模拟试验,获得了这些热控涂层在地球同步轨道15年期间太阳吸收率性能退化模拟数据,与已有的飞行试验数据进行对比研究,取得满意的结果。     

模拟地球同步轨道辐照环境对光学太阳反射镜性能的影响

研究了模拟地球同步轨道辐照环境对卫星用温控涂层-光学太阳反射镜(OSR)性能的影响。对所研制的两类OSR 片进行的辐照试验项目有,真空紫外辐照、低能电子和两种能量的质子辐照。此外还进行了等离子体环境条件下的表面充/放电效应试验。经过相当于安装在地球同步轨道卫星南北极位置处,在空间七年所受到的电子、质子和紫外辐照总剂量的辐照后,导电型OSR 的太阳光谱吸收率α_s 由0.068增加到0.078,法向发射率ε_n 由0.83降低到0.72;而非导电型OSR的α_s 由0.066增加到0.085,ε_n 由0.82降低到0.76。表面充/放电试验的结果表明:导电型OSR 的充电电位仅在15～40V 之间,而非导电型OSR 的充电电位则可高达13kV。因此导电型OSR能有效地控制表面的充/放电现象。     

防静电白色热控涂层的空间环境性能试验

通过在氧化锌晶格中掺入重金属离子，得到具有防静电功能的白色颜料，再以丙烯酸树脂为粘合剂制备出空间飞行器外表面用的ACR－1防静电白色热控涂层；研究了空间环境效应（包括紫外辐照，电子和质子辐照）对该热控涂层太阳吸收率的影响并与有机硅白色热控涂层进行了比较，地面模拟空间环境试验研究结果证明，ACR－1防静电白色热控涂层具有良好的空间稳定性。     

热控涂层太阳吸收比α_s随入射角的变化及其影响

介绍了测量太阳吸收比αｓ。的稳态卡计法原理。用这种方法测量了一些热控涂层的太阳吸收比随温度和入射角的变化。测量结果表明,对二次表面镜及铝光亮阳极氧化涂层,太阳吸收比随人射角的变化是显著的。根据这些测量结果,计算了某些类型卫星吸收的太阳热流量。计算结果表明,对采用二次表面镜或铝光亮阳极氧化涂层的卫星,在计算吸收的太阳热流量时,必须考虑太阳吸收比随人射角的变化。     

AIT环境对卫星热控白漆性能影响的试验

热控白漆喷涂之后至卫星发射之前需要经过数个月的部件组装和测试（AIT）阶段,AIT环境是否影响热控白漆的性能是一个疑问。将与卫星天线相同热控ACR-1白漆的试验膜放置在AIT环境中,对其吸收率和发射率进行了六次测量。通过测量数据,对比分析了AIT过程中温度、湿度、洁净度等环境因素对热控白漆性能的影响程度。结果表明,在试验周期内,ACR-1白漆的吸收率和发射率变化量不大,对白漆性能可靠性的影响度不明显;洁净度对ACR-1白漆的吸收率影响较大。因此,在AIT阶段卫星环境应保持较高的洁净度。     

航天器用新型聚酰亚胺薄膜性能研究

原子氧是低地球轨道环境中对航天器影响较为严重的因素之一. 为了提高聚酰亚胺薄膜抗原子氧侵蚀的性能, 依据结构与性能的关系, 设计合成了新型的聚酰亚胺薄膜. 采用这种新型聚酰亚胺薄膜制备了二次表面镜, 利用地面模拟设备对热控涂层进行原子氧暴露试验, 结果表明其具有优异的耐原子氧侵蚀性能. 此外, 真空elax-elax紫外、真空elax-elax质子、真空elax-elax电子辐照等空间环境模拟试验表明, 这种耐原子氧聚酰亚胺薄膜二次表面镜热控涂层具有良好的空间稳定性.      

航天器材料KAPTON和F4.6薄膜充电性能研究

Kapton和F4.6是两种航天器上最常用的重要热控材料,但它们都是高绝缘的有机高分子聚合物,故在充分利用它们的优良物化性质时,不能不关心它们在空间亚暴环境下表面充电的性能。为此本文在简述了新增环境温度变化的条件后,详细讨论了这两种材料在模拟空间真空、空间亚暴时电子辐照、太阳辐照及其所处环境温度变化时,它们表面电阻率随环境变化响应规律,并由此预测其充电的状态。     

热控涂层紫外辐照试验方法的研究

几种有机热控涂层在真空下进行模拟太阳紫外辐照的试验。在真空条件和大气条件下测试涂层性能的变化,以比较热控涂层在进行紫外辐照时,原位测试和非原位测试的差异。     

太阳吸收率计算公式的截断误差

详细地分析了工程上应用的太阳吸收率计算公式的截断误差;从数学上推导了截断误差的计算公式;并给出了计算实例。所得结果对卫星热控材料及太阳光谱利用涂层材料的光热学性能的测量具有一定的参考价值。     

以聚酰亚胺为基底的柔性导电型第二表面的性能与应用

简略讨论了以Ｋａｐｔｏｎ为基底的柔性导电型第二表面镜的制备，描述了卫星使用的多层隔热结构及接地方法。测试数据表明加有透明导电膜的ＳＳＭ的发射率和太阳吸收率几乎没有改变，因此表明导电膜对热控或隔热效果无丝毫影响。仿照卫星实用的多层隔热结构，最外层采用导电型ＳＳＭ与无导电膜的ＳＳＭ两种材料，在接地与不接地方式下经过模拟亚暴环境的电子辐照试验，７个试样的试验结果显示出加有导电膜的ＳＳＭ防静电性能比不加导电膜的试样极大地提高了。在接地条件下，可把表面电势有效控制在百伏以下，并有力地抑制了表面放电。即使不接地也可降低表面电势值。实验证实表面改性技术和接地技术相结合可以实现最佳的防止卫星表面充放电效果。     

Degradation of thermal control materials under a simulated radiative space environment

A spacecraft with a passive thermal control system utilizes various thermal control materials to maintain temperatures within safe operating limits. Materials used for spacecraft applications are exposed to harsh space environments such as ultraviolet (UV) and particle (electron, proton) irradiation and atomic oxygen (AO), undergo physical damage and thermal degradation, which must be considered for spacecraft thermal design optimization and cost effectiveness. This paper describes the effect of synergistic radiation on some of the important thermal control materials to verify the assumptions of beginning-of-life (BOL) and end-of-life (EOL) properties. Studies on the degradation in the optical properties (solar absorptance and infrared emittance) of some important thermal control materials exposed to simulated radiative geostationary space environment are discussed. The current studies are purely related to the influence of radiation on the degradation of the materials; other environmental aspects (e.g., thermal cycling) are not discussed. The thermal control materials investigated herein include different kind of second-surface mirrors, white anodizing, white paints, black paints, multilayer insulation materials, varnish coated aluminized polyimide, germanium coated polyimide, polyether ether ketone (PEEK) and poly tetra fluoro ethylene (PTFE). For this purpose, a test in the constant vacuum was performed reproducing a three year radiative space environment exposure, including ultraviolet and charged particle effects on North/South panels of a geostationary three-axis stabilized spacecraft. Reflectance spectra were measured in situ in the solar range (250–2500 nm) and the corresponding solar absorptance values were calculated. The test methodology and the degradations of the materials are discussed. The most important degradations among the low solar absorptance materials were found in the white paints whereas the rigid optical solar reflectors remained quite stable. Among the high solar absorptance elements, as such the change in the solar absorptance was very low, in particular the germanium coated polyimide was found highly stable.     

用于热控涂层性能原位测试的辐射计设计

针对空间环境中热控涂层性能退化的问题,提出一种模拟空间环境中利用测热法实现热控涂层太阳吸收率原位测试的辐射计设计方案.结合模拟空间环境的测试要求,进行辐射计的原理设计与理论研究;对辐射计进行结构热分析,建立辐射计测试过程中各项换热的计算式,从而得到辐射计的瞬态计算模型.恒温测试环境下利用辐射计对SR107热控涂层进行了测试.实验结果表明:辐射计测试的SR107热控涂层太阳吸收率值与该涂层的标定值之间的相对误差在2%以内,测试的不确定度为6.3%,实验结果验证了该测试方法的有效性.      

玻璃型二次表面镜的卫星飞行试验

文章介绍了兰州物理研究所研制的石英玻璃型二次表面镜（ＯＳＲ）的卫星搭载试验结果，并对ＯＳＲ的长期空间稳定性作了初步预测。试验和计算结果表明，其ＯＳＲ的太阳吸收率的１０年增值△αｓ预计不超过０．０５５，与国外同类产品的空间稳定性水平相当，已能满足卫星应用的要求。     

组合光学太阳反射镜的热辐射性能测量

用量热计法测量了通信广播卫星上用的光学太阳反射镜（ＯＳＲ）的太阳吸收比αｓ和半球发射率εＨ。为了准确计算卫星的温度分布,测量的是组合ＯＳＲ样品的热辐射性能。作为对比,同时还用量热计法和光谱法测量了单片ＯＳＲ的太阳吸收比,并且对各个测量结果及其差异进行了分析。分析表明,不应当将单片ＯＳＲ的法向太阳吸收比αｓ作为设计参数,否则将在温度计算中引起较大误差。     

Progress on Solar Physics Research in China

The progress on Chinese Space Solar Telescope (SST) in 2002-2004 is introduced. The documentations on plans and outlines based on the standards of Chinese aerospace industry for SST mission has been fulfilled. The key technical problems of SST satellite platform and payloads are tackled during pre-study stage of the mission. The laboratory assembly and calibration of the main optical telescope of 1.2 m spherical mirror and 1 m plain mirror have been carried out with the accuracy of λ/40 and λ/30, respectively. The prototype at 17.1 nm for extreme ultraviolet telescope is under development and manufacture with a diameter of 13 cm. Its primary and secondary mirrors have a manufacturing error of 5 nm with a roughness degree of less than 0.5 nm and a multiplayer reflection factor of better than 20%. The on-board scientific data processing unit has been developed. Prototypes for other payloads such as H. and white light telescope, wide band spectroscopy in high energy and solar and interplanetary radio spectrometer have been developed accordingly.     

Progress on Space Solar Telescope in 2002-2004

The progress on Chinese Space Solar Telescope (SST) in 2002-2004 is introduced. The documentations on plans and outlines based on the standards of Chinese aerospace industry for SST mission has been fulfilled. The key technical problems of SST satellite platform and payloads are tackled during pre-study stage of the mission. The laboratory assembly and calibration of the main optical telescope of 1.2 m spherical mirror and 1 m plain mirror have been carried out with the accuracy of λ/40 and λ/30, respectively. The prototype at 17.1 nm for extreme ultraviolet telescope is under development and manufacture with a diameter of 13 cm. Its primary and secondary mirrors have a manufacturing error of 5nm with a roughness degree of less than 0.5 nm and a multiplayer reflection factor of better than 20%. The on-board scientific data processing unit has been developed. Prototypes for other payloads such as H and white light telescope, wide band spectroscopy in high energy and solar and interplanetary radio spectrometer have been developed accordingly.